CABINETS TO GO Findley & Myers SB24 User manual

Page 1
VanitySinkBase&SinkBaseCabinet 
ASSEMBLY INSTRUCTIONS
Theseassemblyinstructionsareonly applicableforallSinkBase & Vanity Sink BaseCabinets
ITEM#SB24,SB30,SB33,VSB24,VSB30

Page 2
►Items Quantity
Item Description Qty
A
B
C
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT
1-800-CABINET.
►Required tools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a b c
Qty 4 Q ty 4 Qty 8
A
A
F
B
E
B
C
FaceFramewithDoors & Drawer Front 1
SidePanels 2
BottomPanel 1
BottomBackBrace 1
TopBackBrace 1
ToeKick 1
HardwareBox:
Bumper4pcs,Plasticcornerbracket4pcs,1/2"roundheadscrews8pcs
A
D
D
E
F
G1
A
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.

Page 3
►Instructions:
1. Placethefaceframe (A) facedownon aflatsoftworkingsurfacetoensurethatthefaceis 
notscratchedordamaged (Figure1) .
2. InstallingtheSidePanels(Figure2): Insertrightandleftsidepanels (B) int othegrooves of
the face frame (A) and align th e cam lock connectors (Figure 2). Lock the cam
withascrew driver byturningthe screw180°clockwise (Figure4) .
3. Ins tallingtheBottom(Figure3): Gentlyspreadthesidepanelsandinsertthebottom (C)
intothegroovesofsidepanel s (B) untilitis seated inthefaceframe (A). Alignitandlockeachcam.
4. InstallingtheBackBracesandToeKick(Figure5): Placethebottom backbrace (D)and top
back brace (E) atrear of side panels (B.)  Align and lock each cam lock. Install the Toe Kick (F) by
locking the camlock atbothends (Figure5).
Figure 1
A
Figure 2
B
B
Figure
4
Figure 3
B
B
C
D
F
B
Figure 5
E
C
B

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwitha screwdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
5. InstallingtheCornerBraces(Figure6): Placethecorner
braces(b)oneachtopcornerofthecabinetandsecurethemwiththe½”Corner BraceScrews (c).
Install the rubber bumpers (a) onto the corners of the door (A) where it contacts the frame.
Figure 6
b
b c
Q ty 4 Qty 8
a
Qty 4
► Maintenance
For daily cleaning, use a dry cloth and a soft
liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong ble ach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.