CABINETS TO GO Findley & Myers BBC42 User manual

Page 1
BlindBaseCabinet 
ASSEMBLY INSTRUCTIONS
Theseassemblyinstructionsareonly applicableforallBlindBaseCabinets.
ITEM#BBC36,BBC39,BBC42,BBC45

Page 2
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
►Items Quantity
Item Description Qty
A Face Frame with Door 1
B Side Panels 2
C Bottom Panel 1
E Back Panel 1
F Shelf 1
G ToeKick 1
H DrawerFront 1
I DrawerBox 1
J Hardware Box: 2
Bumper6pcs,Plasticcornerbracket4pcs,1/2"roundheadscrews8pcs,Shelfclips4pcs,1/2"flatheadscrewsforslide6pcs
1"screws3pcs, Drawer rail holder 2pcs, Drawer Slide Rails (right & left) 2pcs
►Required tools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a b ge
Qty 6
f
Qty 3
cd
h
Qty 2Qty 2 - 1 Set Qty 6 Q ty 4 Qty 8 Qty 4
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials; therefore, your item may contain a smaller number of each.

Page 3
►Instructions:
1. Place the face frame (A) facedownonaflatsoftworkingsurfacetoensurethatthefaceis  not
scratched or damaged. (Figure1) .
2. InstallingtheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) and align the cam lock connectors (Figure 2). Lock the cam with a
screwdriver by turning the screw 180° clockwise. (Figure4) .
3. InstallingtheBottom(Figure3): Gentlyspreadthesidepanelsandinsertthebottom panel (C)
intothegroovesofsidepanels (B) until itis fully seated in the groove ofthefaceframe. (A).
4. InstallingtheBackPanelandToeKick(Figure5): Before you start this step, put the
back panel (E) on a flat surface facing upward. Install the drawer rail holders (g) inthepre‐
spotted area on the back panel (Figure 6). The opening of the holders should be
 facing towards
eachother.Securethemwith2flatheadscrews(e) each.( Figure6). Thenputtheback
panel (E) atrear of side panels (B)(Figure5) . Align and lock each cam lock. Install the Toe Kick (G)
bylockingthe camlockatbothends (Figure5).
5. Installing the Shelf: Stand the assembled cabinet upright with the frame facing you. Insertthe
shelfclips (d) intothepre-drilled holes on the side panels atthe desired height and install the shelf
(F) from the top locking it into the clips.
6. Installing the Drawer Slide Rails (Figure 7): Insertthedrawersiderail (h)back endintothe
holder (g) previously installed (Step 4) on the back panel. Then secure the drawer rail frontend with
1/2”screws(e) usingthepre‐drilledholesinthefaceframe. (Repeat this step for both sides.)
7. Drawer Assembly (Figure 8): First assemble the drawer front (H)with drawer box front (I) by
usingscrews (f).Thenassembletherestpartsofdrawerbox (I) onto the assembled drawer front.
Figure 1
I E
Figure 7
H
Figure 8
G

8. InstallingtheCornerBraces(Figure9)andinsertingtheDrawer: Placethecorner braces
(b)oneachtopcornerofthecabinetandsecurethemwiththe½”CornerBraceScrews (c).
Slidethedrawerintotherailsandcheckthedrawerposition and adjustslideraillocation  for
bestoperationifnecessary. Install the bumpers (a) on the door and drawer front.
g 
E
g

I
b
h
f
Figure 5
Figure 2
Figure 3 Figure 4
Figure 6Figure 9

Page4
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners contain
ing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.