CABINETS TO GO Findley & Myers VSB30DL User manual

Page 1
VanitySinkBasew/Drawer 
ASSEMBLY INSTRUCTIONS
Theseassemblyinstructionsareonly applicableforallVanitySinkBasew/Drawer
ITEM#VSB30DL,VSB30DR,VSB36DL,VSB36DR

Page 2
►Items Quantity
Item Description Qty
A
B
C
►General Instructions:
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT
1-800-CABINET.
►Requiredtools:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
►Hardware Box:
a b c
Qty 12 Q ty 4 Qty 8
A
A
F
B
E
B
C
FaceFramewith2 Doors & 3 Drawer Fronts (Drawer Fronts: 1 Long Fixed, 2 Short) 1
SidePanels 2
BottomPanel 1
1
1
ToeKick
2
HardwareBox:
Bumper12pcs,Plasticcornerbracket4pcs,1/2"roundheadscrews8pcs, 1" screws 10pcs, Slide Rails 2 Sets, Slide Rail Supports 4pcs
A
D
D
E
F
G1
A
A
A
Drawer Box: Front 2pcs, Back 2pcs, Sides 4pcs, Bottom 2pcs
Back Panel
Fx2
d
Qty 10
f
g
Qty 4Qty 4 (2 Sets)
1/2"flatheadscrews for slides12pcs
e
Qty 12
The materials listing above are for the largest unit in this instruction set. Smaller units may require less
hardware and materials; therefore, your item may contain a smaller number of each.

f
D
e
&ŝŐƵƌĞϲ
Top
f
Page 3
►Instructions:
1. Placethefaceframe (A) facedownon aflatsoftworkingsurfacetoensurethatthefaceis 
notscratchedordamaged (Figure1) .
2. InstallingtheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
the face frame (A) and align the cam  lock connectors (Figure 2). Lock the cam
withascrew driver byturningthe screw180°clockwise (Figure4) .
3. InstallingtheBottom(Figure3): Gentlyspreadthesidepanelsandinsertthebottom (C)
intothegroovesofsidepanels (B) until itis seated inthefaceframe (A). Alignitandlockeachcam.
4. InstallingtheBackPanelandToeKick(Figure5): Before you start this step, place the back panel (D) on a flat surface facing
upward. Install the drawer rail holders (f) in the pre- spotted area on the back panel (Figure 6). Secure them with 2 flat head screws (e)
(Figure 6). Placethebackpanel (D) atrear of side panels
 (B.)  Align and lock each cam lock. Install the Toe Kick (E) by locking the
camlock atbothends (Figure5).
Figure 1
A
Figure 2
B
B
Figure
4
Figure 3
B
B
C
D
E
B
Figure 5
C
5. Drawer Assembly (Figure 7): First assemble the drawer front (A) with drawer box front (F)
with screws
(d). Then assemble the rest of the parts of the drawer box (F) using your palm, or a
rubber mallet if needed, to secure the dove tails into position. Repeat step for 2nd drawer and set
them aside.
A
F
Figure 7
F
f
Qty 4
e
Qty 8
d
Qty 10
d

Page 4
1. Place the face frame (A) face downona flatsoftworking surfacetoensure thatthe
faceis not scratched or damaged. (Figure 1) .
2. InstalltheSidePanels(Figure2): Insertrightandleftsidepanels (B) intothegrooves of
thefaceframe (A) andalignthecamlock connectors (Figure2). Lockthe camwithascrewdriver
byturningthescrew180° clockwise (Figure4) .
3. InstalltheBottom and Microwave shelf(Figure3): Gently spreadtheside panels (B)and
insert (C) & (D) intothegroovesofsidepanels (B) untilthey areseated in theface frame (A).
4. Installing theBack PanelandToeKick (Figure5): Beforeyoustartthisstep,putthe
backpanel (E) onaflatsurfacefacingupward.Installthedrawer slide supports (f) inthepre‐
spottedareaonthebackpanel (Figure6). Thebottom of the slide supports should be facing
the bottom groove.Securethemwith2screws each (e)( Figure6).
Theninstallthe backpanel (E)
to the rearofsidepanels (B)(Figure5) .Alignandlockeachcamlock.InstalltheToeKick (F) by
lockin
7. InstallingtheCornerBraces(Figure9): Placethecorner
braces(b)oneachtopcornerofthecabinetandsecurethemwiththe½”Corner BraceScrews (c).
Insert the assembled drawers from Step 5. Install the rubber bumpers (a) onto the corners of the
doors and drawers (A) where they contact the frame.
Figure 9
b
b c
Q ty 4 Qty 8
a
Qty 12
► Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
N
ever u se abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets etc.
Good ventilation is essential for maintaining the q uality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by email
- [email protected] or call 1-800-CABINET.
6. Install the Drawer Slide Rails: Insert the drawer side rail's back end (g) into the
holder (f) previously installed (Step 4) on the back panel (D) (Figure 8).
Then secure the drawer rail front end with 1/2” screws (e) using the pre-drilled holes in the face frame (A).
Figure 8
Top
g
f
g
Qty 4 (2 Sets)
e
Qty 4