CABINETS TO GO Findley & Myers OC3384 User manual

ASSEMBLY INSTRUCTIONS
These assembly instructions are only applicable for all Single/Double Oven Cabinets
ITEM# OC3384, OC3390
Page 1

►Items Quantity
Item Description Qty
A
Left Side Panel 1
B
Right Side Panel 1
C Back Panel
1
D Top & Bottom Panel
2
E Frame, 2 Doors & 3 Drawer Fronts 1
F
G
Hardware Box
3
Bumper 16pcs, 1/2" Round Head Screws 36pcs, 1" Flat Head Screws 15pcs, Glide Brackets 6pcs, Drawer Clips 6pcs
► Required tools:
►General Instructions:
Tools Required: Phillips Screwdriver Optional Tools: Electric Drill Optional Tools: Rubber Mallet
► Hardware Box:
a b
c
Q ty 15 Qty 36 Qty 16
ThankyouforpurchasingaCabinetsToGoproduct.Youarenowtheproudownerofahighqualityproductdesigned
tofacethetestofdaily useandguaranteeingyourenjoymentformanyyearstocome.
Carefullyreadtheinstructionsbeforestartingtheinstallation.
Duringassembly,pleasefollowallgenerallyacceptedsafetyprocedures.
FailuretoadheretothefollowinginstructionswillinvalidatethewarrantyandCabinetsToGowilldeclineany responsibilityforany
damagescaused.Anyinstallationwhichdoesnotcorrespondtotheinstructionsmayresultin defects,malfunctioningparts,significant
damageand/orinjury.
Beforetheassemblybegins,checkthatallappropriateandrequiredplumbingandelectricalconnectionsexist.
Beforedrilling,makeabsolutelysurethattherearenopipes(gas,water,electricity,heating,etc.)atthedrilling location.CabinetsToGowill
notbeheldresponsibleforfailuretofollowtheseinstructions.
PRIOR TO ASSEMBLY, PLEASE MAKE SURE YOU HAVE ONE FACE FRAME BOX AND ONE CARCASS BOX, WHICH HAVE ALL THE PARTS IN THE
QUANTITIES MENTIONED BELOW. IF YOU ARE MISSING ANY PARTS, PLEASE STOP AND CONTACT CUSTOMER CARE IMMEDIATELY AT 1-800-
CABINET.
Fixed Shelves
e
Q ty 6 Qty 6
H Drawer Panel & Drawer Box: (Front, Back, Sides, & Bottom)
Toe Kick
3 Sets
The materials listing above are for the largest unit in this instruction set. Smaller units may require less hardware and materials;
therefore, your item may contain a smaller number of each.
3 Sets
I Drawer Glides
Page 2
d
1
Required Tool: Hand Saw
DOUBLE OVEN CABINET

NOTE:
E
If installing a double oven, you will want to
perform this step first to prepare the frame.
Using a saw, cut the frame as shown below
to remove the un-needed rails.
{ NOTE:Lay Frame and Doors on a flat smooth soft
work surface to prevent damage. }
X
X
SKIP THIS PAGE FOR SINGLE OVEN CABINETS
Page 3
SoftSurface
Hard Surface
E
E
The assembled double oven
cabinet will look like this with
the larger opening, and a
single drawer at the bottom.

b
d
X12
X6
1
2
C
A
B
E
Install the glide brackets (d) to the Back
Panel (C) using screws (b). (Figure 1)
{ NOTE: Lay Back Panel on a flat smooth soft work
surface to assemble. }
SoftSurface
Hard Surface
C
C
Figure 1
Page 4
Figure 2
Assemble the Side Panels (A,B) onto the
Frame (E) by connecting the male and
female cam locks and using a screwdriver
to turn the lock clockwise. (Figure 2)

G
D
D
3
4
Figure 3
Insert the Top & Bottom Panel
(D) into the grooves of the Side
Panels and Frame.
(Figure 3)
Figure 4
Install the toe kick (G)
onto the side panels (A,B)
and lock the cam locks.
(Figure 4)
Page 5

5
6
C
F
F
F
Figure 5
Insert the Fixed Shelves (F)
into the grooves of the Side
Panels and Frame.
(Figure 5)
Figure 6
Page 6
Install the Back Panel (C)
onto the side panels (A,B)
and lock the cam locks.
(Figure 6)

H
c X12
c
7
8
H
Figure 8
Page 7
Figure 7
Finish assembling the
drawer boxes. (H) (Figure 8)
{ NOTE: You may use a rubber
mallet if needed to seat the
dove tails. }
Optional Tools: Rubber Mallet
Assemble the drawer front
(H) onto the drawer box front
using the supplied screws
(a). Place bumpers (c) onto
the corners of the drawer
front. (Figure 7)
a X15

I
10
9
Figure 9
Figure 10
Attach the Drawer Clips (e) using
screws (b) onto the bottom of
the drawers. (H) (Figure 9)
Page 8
H
e X6
b X18
b X6
Attach the Drawer Glides (I)
using screws (b) onto the
frame and glide brackets
installed in Step 1. (Figure 10)

c
11
12
Install the remaining bumpers (c)
onto the corners of the doors
where they come in contact with
the frame.
(Figure 11)
Insert the assembled drawers
(H) onto the glides. Push in
until you hear clicks from the
drawer clips locking into the
glides. (Figure 12)
Figure 11
Figure 12
Page 9
c X4

Page 10
►Maintenance
For daily cleaning, use a dry cloth and a soft liquid cleaner.
Never use abrasive cleaners containing acetone, chlorine or strong bleach. Also, do not use tools as scrapers,
metallic brushes, and other products which can scratch or tarnish surfaces.
Under no circumstances should you use chrome cleaner on chrome-plated or brass trim, hinges, handles, sockets
etc.
Good ventilation is essential for maintaining the quality and look of this furniture.
Warranty and Customer Care Information
For the most up to date warranty information for your product, please visit our website - www.cabinetstogo.com to get
the specific details. If you have any questions with warranties or to make a claim, please contact Customer Care by
email - [email protected] or call 1-800-CABINET.