Canon Paper Craft User manual

Mountain fold (dotted line)
Make a mountain fold.
Valley fold (dashed and dotted line)
Make a valley fold.
Cut line (solid line)
Cut along the line.
Cut in line (solid line)
Cut along the line.
Tools
Scissors, glue, ruler, tweezers, pencil
![Caution] Glue, scissors and other tools may be dan-
gerous to young children so be sure to keep them out of
the reach of young children.
Assembly Instructions
Try to avoid bending the parts when you cut them out.
When assembling the parts, follow the assembly in-
structions and use the parts in the order given.
When sticking surfaces together, spread the glue evenly
and stick the parts together quickly and line up the
edges cleanly. While the glue is drying, put the fuse-
lage inside a sheet of paper and then press it down with
a book or similar in order to get a nice, straight finish.
When sticking the right and left wings together, make
sure that the center line is not off center.
Center line
To glue the wings flush onto the fuselage, use a pencil
or scissors to flatten out the part where the wings at-
tach to the fuselage.
Rub with pencil or scissors
to flatten out.
Flatten the uneven surface.
Cross section of the fuselage
To give the wings an angle, bend along a straight
ruler. (Refer to the assembly instructions for details on
what degree of angle to use.)
Dihedral angle
Attach the wings and horizontal stabilizer carefully so
that their center lines match up exactly with the center
line of the fuselage.
Make sure that the center line of
the wings matches up exactly
with the center line of the fuselage.
Also attach the horizontal stabilizer firmly.
Arrow points forward.
Arrow points forward.
If any of the cut out parts are bent, this will seriously
affect the glider's performance. Therefore, be sure to
keep all parts perfectly flat till you join them up. For
the wings, stabilizer and other parts, use a ruler to
give you a proper straight edge to make your folds.
Align the parts
against a ruler to fold them.
Points to note when making the glider
http://www.canon.com/c-park/en/
- 1 -
Flying-Boat: Assembly Instructions

8mm approx.
(1/3")
Fold all tabs outward.
Aligning the noses flush,
glue through together
in the order shown.
Assemble the sponson. (Sponson: a projection on the side of the fuselage.)
Arrow points forward.
Arrows point forward.
Fuselage
Placing a ruler along the dashed line on both edges
of the main wing ( + ), bend the strips upward
to make a dihedral angle of 10˚.
Glue the main wing firmly to the fuselage.
Camber the main wing ( + )
after the curve of its gluing position on the fuselage.
Glue to the upperside of aligning the dashed line
on both edges of . When dry, cut off the protruding portions.
Glue the horizontal stabilizer
to the fuselage.
Glue the sponson to the printed box on the left side
of the fuselage. Glue the sponson to the printed box
on the right side of the fuselage.
View the fuselage from the front. Before the glue dries thoroughly,
fix the sponsons and to ensure that they are glued horizontally.
Insert a pencil into the sponson and swell it
again to make it into a streamline shape.
Fold all tabs on . Swell the inside of the two folds of .
Then spread glue on the shaded portion
as shown in the figure and glue the part
together to complete its bag shape.
Assemble part in the same manner.
GLUING INSTRUCTIONS
Glue the parts together in the order indicated.
- 2 -
Flying-Boat: Assembly Instructions

10˚
10˚
Using the engine installation lines and cuts on the main
wing as a guide, glue the four engines to the main wing.
Adjust the camber of both the main wing
and the wing tips carefully with your fingers.
Using the dihedral angle gauge, make sure
the dihedral angle for the main wing is 10˚.
View the plane from both the front and the back
and straighten any warps or bends in the fuselage
and the wings.
Camber the wing tips carefully.
Camber the wing tips carefully.
Camber the wing carefully.
Dot towards the front.
Dot towards the front.
According to the curve of the gluing position
for the main wing on the fuselage,
camber the main wing ( + ) evenly up
to both edges. Make sure that the dihedral
angle for the folded tabs are 10˚.
Camber both wing tips and
equally to the main wing.
Apply glue to the top surface of the folded tabs of the
main wing and attach wing tips and respectively.
Before it dries, adjust the dihedral angles of and
to 10˚. (Use the dihedral angle gauge.)
Fold the tabs on through .
Glue together and , and , and , and to make four engines.
FINISHING TOUCHES
Give the finishing touches to the plane after it dries thoroughly.
- 3 -
Flying-Boat: Assembly Instructions