Canon PAPER CRAFT Euoplocephalus User manual

1
Before starting assembly:Writing the number of each section on its back
side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out
the sections.)
Indicates where sections
should be glued together.
Indicates sections that
should be glued first,
then cut out.
©Canon Inc. ©Y. Watanabe
http://www.canon.com/c-park/en/
Euoplocephalus : Assembly Instructions
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
Assembly Instructions : Five A4 sheets (No. 1 to No. 5)
*This model was designed for Papercraft and may differ from the original in some respects.
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
View of completed model
1
Assembled parts 1 - 2
3
4
Assembled parts 1 - 4
5
6
7
2Assembling the tail : Parts 1 - 7

2
©Canon Inc. ©Y. Watanabe
Euoplocephalus : Assembly Instructions
8
9
10
Assembled parts 8 – 11
Left rear leg
Right rear leg
Tail
16
17
18 19
20
11
Assembling the left rear leg : Parts 8 - 11 Assembling the lower back and the torso : Parts 16 - 20
Assembling the right rear leg : Parts 12 - 15
Parts 8, 9, 10, and 11 make the left rear leg.
Parts 12, 13, 14, and 15 make the right rear leg.
Build both the left and right rear legs in the same way.

3
©Canon Inc. ©Y. Watanabe
Euoplocephalus : Assembly Instructions
21
22
23
24
25
26
27
28
Parts 25, 26, 27, and 28 make the right front leg.
Parts 29, 30, 31, and 32 make the left front leg.
Build both the left and right front legs in the same way.
Assembling the torso : Parts 21 - 24 Assembling the right front leg : Parts 25 - 28
Assembling the left front leg : Parts 29 - 32

Assembling the torso : Parts 33 and 34 Assembling the head and neck : Parts 35 - 39
4
©Canon Inc. ©Y. Watanabe
Euoplocephalus : Assembly Instructions
39
38
37
36
35
34
33
Left front leg
Right front leg

5
©Canon Inc. ©Y. Watanabe
Euoplocephalus : Assembly Instructions
40
40
41
40
40
41
41
43
43
42
42
42
41
43
43
42
42
42
43
45
44
44
45 45
44
44 44 46
48
47
54
49
51
49
51
45
45
45
45
43
45
44
45
44
44
44 44
44
45 45
45
45
44
44
44 44
45
45
47
46
53
Finished!
52
52
50 50
Assembling the bony armor :
Parts 40 - 54
Assembling the bony armor :
Parts 40 - 54
Fold parts 40 through 53 in two and
glue both sides together before cutting
out these parts.