Caple WC1800 User manual

Fully Integrated In-Column Wine
Cabinet Instruction Manual
WC1800
Contact Caple on 0117 938 7420 for spare parts or www.caple.co.uk

2
Instruction manual WC1800
2Please keep this instruction manual for future reference
CONTENTS
Important Safety Instructions 3
Installation Warnings 8
Ambient Temperature 9
Control Panel 10
Using the Shelves 12
How to Replace the Charcoal Filter 13
How to Change the Door Opening 14
Wine Bottle Stacking 15
Installation Dimensions 16
Installing the Fixing Brackets 17
Installing the Furniture Door 18
Care and Maintenance 20
Recommended Temperatures 22
Troubleshooting Guide 23
Caple Contact Details 24

3
3
Instruction manual WC1800Please keep this instruction manual for future reference
INTRODUCTION
Thank you for buying your new Caple Wine Cabinet.
To ensure that you get the best results from your new purchase, we strongly suggest that you read
this instruction manual thoroughly before use. This manual contains installation advice, usage
instructions and other important facts about your Caple Wine Cabinet. If treated with care your
appliance will give you many years of trouble free use.

4
Instruction manual WC1800
4Please keep this instruction manual for future reference
WARNINGS
-To prevent damaging the door gasket, make sure the
door is fully open when pulling shelves out of the rail
compartment.
-The appliance must be positioned so that the plug is
accessible. Release the electric cord and move your
cabinet to its final location. Do not move your cabinet
while loaded with wine as you may distort the body.
-The wine cabinet should be installed in a suitable place
in order to avoid touching the compressor.
-After unpacking, make sure that the appliance is in
perfect order. If you have any doubt, do not use it and
contact your retailer.
-If the supply cord is damaged, it must be replaced by
a Caple service agent or a similarly qualified person in
order to avoid a hazard.
-This product is not designed for commercial use, it is a
household appliance only.
It is not intended to be used in:
• Staff kitchen areas in shops, offices and other working
environments
• Bed and breakfast type environments
• By clients in hotels, motels and any other residential
type environments
-This appliance is intended to be used exclusively for the
storage of wine.

5
5
Instruction manual WC1800Please keep this instruction manual for future reference
IMPORTANT
Caple cannot be held liable for any non compliance with
these instructions.
ELECTRICAL SHOCK HAZARD
To reduce the risk of fire, electrical shock, or injury
when using your appliance, follow these basic precautions:
-Read all instructions before using the wine cabinet.
-DANGER or WARNING: Risk of child entrapment.
-Before you throw away your old wine cabinet: Take off
the door, leaving the shelves in place so that children
cannot easily climb inside.
-Never allow children to operate, play with, or crawl
inside the appliance.
-Never clean appliance parts with flammable fluids. The
fumes can create a fire hazard or explosion.
-Do not store or use gasoline or any other flammable
vapours and liquids in the vicinity of this or any other
appliance. The fumes can create a fire hazard or
explosion.
-The refrigerant of this appliance is R600a, flammable
and explosive articles should not be put in or near the
cabinet, to avoid the risk of fire or explosion.
-This appliance can be used by children aged from 8

6
Instruction manual WC1800
6Please keep this instruction manual for future reference
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance.
-Cleaning and user maintenance shall not be made by
children without supervision.
-When positioning the appliance, ensure the supply cord
is not trapped or damaged.
-Do not locate multiple portable socket-outlets or
portable power supplies at the rear of the appliance.
-Do not use plug adapter.

7
7
Instruction manual WC1800Please keep this instruction manual for future reference
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice. This appliance is
marked according to the European directive on Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. The symbol on the product indicates that this
product may not be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. Disposal must be carried
out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please
contact your local council, your household waste disposal service or the retailer where you
purchased the product.
CE DECLARATIONS OF CONFORMITY
This appliance has been manufactured to the strictest standards and complies with all applicable
legislation, Low Voltage Directive (LVD) and Electromagnetic Compatibility (EMC).
TECHNICAL FICHE
This appliance conforms to all current and applicable energy regulations. To view the Technical
Fiche that supports the energy labelling data, please visit the product page on our
website www.caple.co.uk
Symbol ISO 7010 W021
Warning; Risk of fire / flammable materials

8
Instruction manual WC1800
8Please keep this instruction manual for future reference
INSTALLATION WARNINGS
BEFORE USING YOUR WINE CABINET:
-Remove the exterior and interior packing.
-IMPORTANT: Before connecting the wine cabinet to the power source, let it stand upright
for at least 12 hours. This will reduce the possibility of a malfunction in the cooling system from
handling during transportation.
-Before installation, turn the unit off and unplug it from the outlet.
Clean the interior surface with lukewarm water using a soft cloth.
NOTE
To protect the appliance in transit and delivery the door is packed tightly against the cabinet.
When first installed this can mean the door seal appears thinner on one side of the door due to
compression, this is normal and once out of the box it will relax over a short period of time and
the door will return to the normal position. If you wish to speed up the process you can gently
warm the seal with a hair dryer on a low temperature setting. This can help relax the seal helping
it return to normal thickness a little faster.
INSTALLATION OF YOUR WINE CABINET:
-The wine cabinet should be installed in a stable and suitably sized kitchen carcass, which has
been appropriately levelled and ventilated.
-To level your wine cabinet, adjust the front levelling leg at the bottom of the cabinet.
-Ensure it is perfectly level, as this will minimise any vibrations.
-This appliance uses flammable refrigerant. Never damage the cooling pipework
during transportation.
-Locate the wine cooler away from direct sunlight and sources of heat (ovens, hobs, heaters,
radiators, etc.). Never clean appliance parts with flammable fluids as the fumes can create a fire
hazard or explosion. When disposing of your appliance, please choose an authorised
disposal site.
-Avoid locating the unit in moist areas.
-It is fitted with a power cord having an earth wire terminating in a 13amp plug.
-Ensure the product is correctly ventilated (see page 16).
-Consult a qualified electrician or service engineer if the earthing instructions are not
completely understood.

9
9
Instruction manual WC1800Please keep this instruction manual for future reference
-Plug the wine cabinet into an exclusive, properly installed-grounded wall outlet. Do not under
any circumstances cut or remove the third (ground) pin from the plug. Any questions concerning
power and/or grounding should be directed toward a certified electrician or Caple service.
WARNING: Incorrect earthing can result in the risk of electric shock
ATTENTION:
-Store wine in sealed bottles
-Do not overload the cabinet
-Do not open the door unless necessary
-Do not cover shelves with aluminium foil or any other shelf material which may prevent
air circulation
-Should the wine cabinet be stored without use for long periods it is suggested, after careful
cleaning, to leave the door ajar to allow air to circulate inside the cabinet in order to avoid
possible formations of condensation, mould or odours.
-Keep the ventilation openings in the appliance enclosure or in the built-in structure, clear
of obstruction
-Do not use mechanical devices or other means to accelerate the defrosting process, other than
those recommended by the manufacturer
-Do not damage the refrigerant circuit
-Do not use electrical appliances inside the storage compartments of the appliance, unless they
are the type recommended by the manufacturer
AMBIENT TEMPERATURES
Please use the cabinet within ambient temperatures between 16-32ºC, if the ambient temperature
is higher or lower than this, it will cause the temperature to fluctuate in the cabinet, possibly
preventing it from reaching 5-18ºC.

10
Instruction manual WC1800
10 Please keep this instruction manual for future reference
CONTROL PANEL
UPPER AND MIDDLE ZONES
TOUCH CONTROL KEYS AND SYMBOLS
To switch the appliance on/off. Press and hold this button for approximately 1 second to
turn the appliance on. Press and hold this button for approximately 3 seconds to turn the
appliance off.
To turn the lock function on/off. Press and hold this button for approximately 3 seconds to
activate/deactivate. When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. Once the temperature reaches
the highest temperature value for the upper or middle zone , it will revert back to its
lowest temperature value.
Upper zone = 5-18ºC
Middle zone = 5-10ºC
Once the required temperature is selected, the LED display will temporarily flash for 5
seconds, then reverts back to the normal display, and the temperature is now set.
NOTE: Press and hold for 3 seconds, to change the display from ºC to ºF.
This button is used to toggle between the different light functions. When selected, the
relevant symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door
is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then
turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds
until flashes. Then use the keys to adjust the brightness of the internal light.
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
CONTROL PANEL AND OPERATION
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold the keys for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. Once the temperature reaches
the highest temperature value for the upper or lower zone, it will revert back to its lowest
temperature value.
Upper zone = 5-10ºC
Lower zone = 10-18ºC
Once the required temperature is selected, the LED display will temporarily flash for 5
seconds, then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
for 3 seconds until
This symbol indicates the brightness adjuster: Hold the light key
flashes. Then use the right hand side keys to adjust the brightness of the internal light.
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
CONTROL PANEL AND OPERATION
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold the keys for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. Once the temperature reaches
the highest temperature value for the upper or lower zone, it will revert back to its lowest
temperature value.
Upper zone = 5-10ºC
Lower zone = 10-18ºC
Once the required temperature is selected, the LED display will temporarily flash for 5
seconds, then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
for 3 seconds until
This symbol indicates the brightness adjuster: Hold the light key
flashes. Then use the right hand side keys to adjust the brightness of the internal light.
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
CONTROL PANEL AND OPERATION
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold the keys for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. Once the temperature reaches
the highest temperature value for the upper or lower zone, it will revert back to its lowest
temperature value.
Upper zone = 5-10ºC
Lower zone = 10-18ºC
Once the required temperature is selected, the LED display will temporarily flash for 5
seconds, then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
for 3 seconds until
This symbol indicates the brightness adjuster: Hold the light key
flashes. Then use the right hand side keys to adjust the brightness of the internal light.
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter

11
11
Instruction manual WC1800Please keep this instruction manual for future reference
This button is used to toggle between the different operational functions. When selected,
the relevant symbol will illuminate:
STANDARD MODE - Select this function to operate the wine cabinet in
standard mode.
ECO MODE - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5 seconds
and then switch off again. The compressor is also delayed 5 minutes in order to
save energy.
INTELLIGENT MODE - In intelligent mode, the wine cabinet will adjust the fan
speed according to the ambient temperature. This will reduce noise levels and
save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is also
disabled during DEMO mode.
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either the
door has been left open for a long period of time, or the temperature has fluctuated too
high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold and for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. The highest temperature is 18ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
then reverts back to the normal display, and the temperature is now set.
Press this button to lower the temperature in 1ºC increments. The lowest temperature is 5ºC.
Once the required temperature is selected, the LED display will temporarily flash for 5 seconds,
it then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
This symbol indicates the brightness adjuster: Hold the light key for 3 seconds until
flashes. Then use the and keys to adjust the brightness of the internal light.
CONTROL PANEL AND OPERATION
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
CONTROL PANEL AND OPERATION
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold the keys for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. Once the temperature reaches
the highest temperature value for the upper or lower zone, it will revert back to its lowest
temperature value.
Upper zone = 5-10ºC
Lower zone = 10-18ºC
Once the required temperature is selected, the LED display will temporarily flash for 5
seconds, then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
for 3 seconds until
This symbol indicates the brightness adjuster: Hold the light key
flashes. Then use the right hand side keys to adjust the brightness of the internal light.
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
CONTROL PANEL AND OPERATION
TOUCH CONTROL KEYS AND SYMBOLS
This button is used to toggle between the different operational functions. When selected, the
relevant symbol will illuminate:
Standard mode - Select this function to operate the wine cabinet in standard mode.
ECO mode - An energy saving mode where both the inner light and control panel
lights are off (except the indicator). The LED display is also switched off, until you
change the temperature using the and keys, this will be displayed for 5
seconds and then switch off again. The compressor is also delayed 5 minutes in order
to save energy.
Intelligent mode - In intelligent mode, the wine cabinet will adjust the fan speed
according to the ambient temperature. This will reduce noise levels and save energy.
DEMO mode - When DEMO mode is selected, the compressor and PTC heater will be
disabled, and the fan input voltage reduces to 9V. The HI/LO temperature alarm is
also disabled during DEMO mode.
Note: Press and hold the keys for 3 seconds, to change the display from ºC to ºF.
To switch the appliance on/off .
Press and hold this button for approximately 1 second to turn the appliance on.
Press and hold this button for approximately 3 seconds to turn the appliance off.
To turn the lock function on/off.
Press and hold this button for approximately 3 seconds to activate/deactivate.
When activated, the symbol will illuminate.
Press this button to raise the temperature in 1ºC increments. Once the temperature reaches
the highest temperature value for the upper or lower zone, it will revert back to its lowest
temperature value.
Upper zone = 5-10ºC
Lower zone = 10-18ºC
Once the required temperature is selected, the LED display will temporarily flash for 5
seconds, then reverts back to the normal display, and the temperature is now set.
This button is used to toggle between the different light functions. When selected, the relevant
symbol will illuminate:
The internal light will switch on when the door is opened, and off when the door is closed.
The internal light is continuously on. However after 3 minutes the light will dim.
The internal light will remain on for 10 minutes once the door is closed and then turn off.
for 3 seconds until
This symbol indicates the brightness adjuster: Hold the light key
flashes. Then use the right hand side keys to adjust the brightness of the internal light.
The cooling symbol will illuminate to show when the wine cabinet is currently cooling.
The alarm symbol will illuminate to show the alarm is on. This will activate when either
the door has been left open for a long period of time, or the temperature has fluctuated
too high or low (HI or LO will also show in display to confirm this).
LOWER ZONE CONTROL PANEL
Press this “ “ button to increase temperature by 1ºC
Press this “ “ button to decrease the temperature by 1ºC
Lower zone: 10-18ºC
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter

12
Instruction manual WC1800
12 Please keep this instruction manual for future reference
Removing the shelves
1.Fully extend the shelf you wish to remove
2.Lift the front of the shelf up to remove from the front clips
3.Holding onto the shelf runner, push the shelf in and then pull up at the back to
release from the rear clips.
=
20
3 Bordeaux
5 Bordeaux
+
3 Bordeaux
+
3 Bordeaux
+
3 Bordeaux
+
3 Bordeaux
+
full shelves
STORAGE DIAGRAM
(for 750 ml Bordeaux bottles)
Glass shelves are available if you wish to store cans or smaller bottles such as beer in
your wine cabinet. These can be purchased directly from www.caple.co.uk
USING THE SHELVES
To prevent damaging the door gasket, make sure to have the door opened fully when pulling
shelves out of the rail compartment.
REMOVING THE SHELVES
1. Fully extend the shelf you wish to remove
2. Lift the front of the shelf up to remove from the front clips
3. Holding onto the shelf runner, push the shelf in and then pull up at the back to release from the
rear clips.
Glass shelves are available if you wish to store cans or smaller bottles such as beer in your wine
cabinet. These can be purchased directly from www.caple.co.uk

13
13
Instruction manual WC1800Please keep this instruction manual for future reference
HOW TO REPLACE THE CHARCOAL FILTER
The charcoal filters are located in the top right corner of each zone. To replace the filters, follow
the below steps:
1. Open the door and remove the top 2 shelves (see removing the shelves).
2. Turn the filter as per Fig A.
3. As per Fig B, the filter should line up with the notches as shown.
4. Pull the filter out (Fig C).
5. Insert replacement filter and twist as per Fig A to lock into position.
6. Re-install the shelves
NOTE: The charcoal filter should be replaced every 3-6 months depending on the unit’s exposure
level to odour.
Visit www.caple.co.uk to purchase the replacement charcoal filters.
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
2
Ø CONTROL PANEL (upper zone and middle zones)
Ø CONTROL PANEL (Lower zone)
“
＋＋
”
Press this button to increase the temperature by 1ºC
“ － ”
Press this button to decrease the temperature by 1ºC.
Lower zone = 10-18ºC
• How to replace the charcoal filter
Fig. A - Locked
Fig. B - Unlocked
Fig. C

14
Instruction manual WC1800
14 Please keep this instruction manual for future reference
1. Open the door and remove the decorative covers(1) on the left hand side as shown in Fig A.
2. Fix the screws into these positions as per Fig B, but do not fasten the screws.
3. Remove all screws from both the upper and lower hinge, and then remove the door.
4. Rotate the door 180 degrees, and place the hinges into the screws fixed in Fig B. Once slotted
onto these screws, tighten the screws to secure the hinges (Fig D).
5. Place the decorative covers in the right hand side screw holes as shown in Fig D.
6
This appliance has a reversible door, and comes delivered with a right hand hinged door.
Should you wish to reverse the hinge on your wine cabinet, follow the instructions below:
打开90度,把左侧的装饰钉拆除
丝旋进左侧门铰安装孔（不要锁
如图B所示
上下门铰紧固螺丝
把上下门铰卡入左侧安装螺丝,然
件装饰钉，把右侧的门铰孔堵塞
1. Decorative covers 2. Door 3. Hinge 4. Screws
Fi g. A
Fi g. C
Fi g.B
Fi g.D
1
2
3
4
4
4
1
1. Open the door and remove the decorative covers(1) on the left hand side as shown in Fig A.
2. Fix the screws into these positions as per Fig B, but do not fasten the screws.
3. Remove all screws from both the upper and lower hinge, and then remove the door.
4. Rotate the door 180 degrees, and place the hinges into the screws fixed in Fig B. Once
slotted onto these screws, tighten the screws to secure the hinges (Fig D).
5. Place the decorative covers in the right hand side screw holes as shown in Fig D.
HOW TO CHANGE THE DOOR OPENING
This appliance has reversible doors but is delivered with a right hand hinged door.
Should you wish to reverse the hinge on your unit, follow the directions below:
Fig. A Fig. B
Fig. C Fig. D
1. Decorative covers
2. Door
3. Hinge
4. Screws

15
15
Instruction manual WC1800Please keep this instruction manual for future reference
Stores max. 70 Bordeaux style bottles 750ml.
PLEASE NOTE:
If you wish to store other style bottles i.e. champagne, the maximum storage capacity will be less
than as shown above. Shelves may also need to be removed to allow more bottles to be stored.
WINE BOTTLE STACKING
Champagne bottle on standard shelf:
Bordeaux bottle on standard shelf:
Bordeaux bottle on display shelf:

16
Instruction manual WC1800
16 Please keep this instruction manual for future reference
INSTALLATION DIMENSIONS
DIMENSIONS
1761mm
38mm
545mm
500mm
580mm
560mm
545mm
545mm
inc. door
1744mm
1680mm
1728mm 1680mm 1744mm
555mm
500mm
50mm
Ventilation
min 200cm² in plinth
VENTILATION:
-The ventilated cross section must be at least 200cm2 and the wine cabinet shall be ventilated
from the kitchen plinth.
-The back panel of the carcass the appliance is installed into shall be removed.
-Where the decorative grill is used it must be noted that the total area of the grill opening
corresponding to the ventilation cross section shall not be less than 200cm2.
NOTE: It is important that the furniture cabinet is completely square and the base is level. If
it is not level the product may appear to lean, this is not a fault of the product and the
installation must be corrected.
Once the product is correctly located in the cabinet, it is important that the feet are adjusted to
level the product.

17
17
Instruction manual WC1800Please keep this instruction manual for future reference
INSTALLING THE FIXING BRACKETS
The wine cabinet comes with two fixing brackets(2) to secure the appliance to the kitchen carcass.
There are also screw holes included in the door hinges that allow you to secure the wine cabinet
to the opposite side of the carcass (Fig. B & Fig. D).
These brackets will keep the wine cabinet secure and help prevent it moving when in use.
6
INSTALLING THE SIDE FIXING BRACKETS
The wine cabinet comes with two fixing brackets(2) to secure the appliance to the
kitchen carcass. There are also screw holes included in the door hinges that allow
you to secure the wine cabinet to the opposite side of the carcass (Fig. B & Fig. D).
These brackets will keep the wine cabinet secure and help prevent it moving when in
use.
①①
Screw
②②
Fixing bracket
③③
Kitchen cabinet
** Marketing – Please
remove Fig.E **
• As per Fig. A, line the fixing bracket up with the two holes at the top of the wine
cabinet, and using the screws provided, secure the bracket onto the appliance.
Once secure, fix the other side of the bracket into the kitchen cabinet using the
screws provided.
2
1
1
2
3
1
1
1
Fig.A Fig.B
Fig.C Fig.D
Fig.E
1. Screw
2. Fixing bracket
3. Kitchen cabinet
-As per Fig. A, line the fixing bracket up with the two holes at the top of the wine cabinet, and
using the screws provided, secure the bracket onto the appliance. Once secure, fix the other side
of the bracket into the kitchen cabinet using the screws provided.
-On the hinged side of the appliance, the hinges include screw holes to secure the appliance to
the opposite side of the kitchen cabinet. Locate these holes as per Fig. B, and using the screws
provided, screw tightly into the kitchen cabinet.
-Repeat this process for the bottom of the cabinet as shown in Fig. C & Fig. D.
Fig. A Fig. B
Fig. C Fig. D

18
Instruction manual WC1800
18 Please keep this instruction manual for future reference
INSTALLING THE FURNITURE DOOR
You will need to install a furniture door frame to the front of the wine cabinet once the wine
cabinet has been installed.
The furniture door frame can be custom made to line up with your other furniture doors in the
kitchen. The door must be finished on both sides in order to prevent warping. In some installations
the door panel may be visible through the glass when the door is open. See below for wine
cabinet door dimensions, and also an example of a furniture door size.
NOTE: The door panel must not weight more than 20kg
NOTE: The door thickness must not exceed 22mm. If a thicker door is used, the door may make
contact with the adjacent furniture door when opened
DIMENSIONS
555mm
1728mm 1744mm
85mm
1680mm 24mm
*The height of the furniture door will need to be adjusted to ensure it lines up with the other kitchen
cabinet doors, therefore these dimensions will vary.
545mm
55mm55mm
19mm
min 145mm
1780mm*
592mm
min 80mm min 80mm
min 145mm
348mm144mm144mm348mm
348mm
348mm
85mm
* The height of the furniture door will need to be adjusted to ensure it lines up with the other
kitchen cabinet doors, therefore these dimensions will vary.
NOTE: The furniture door can extend beyond the appliance door, however you must ensure a gap
of at least 75mm must be left from the bottom of the furniture door to the floor to allow
for sufficient ventilation.

19
19
Instruction manual WC1800Please keep this instruction manual for future reference
NOTE: If a handle is required, please ensure this is installed in an appropriate position before
the furniture door is installed.
1. Fully open door.
2. Starting at the corner, pull the gasket away from the door. As per Fig A.
3. Continue to pull the gasket free from the gasket channel.
4. Upon removal, lay gasket down on a flat surface.
5. Secure the furniture door panel to the appliance door using clamps (see Fig. B).
6. Using a 3mm drill bit, drill 10 pilot holes into the wood panel 12mm deep using the holes in the
door frame as a guide.
Note: It is important to ensure that all drilled holes are drilled to the correct depth in order to
avoid splits in the wood when hardwood is installed. You must also take care not to drill all the
way through the door.
7. Locate 10 of the M4x34mm screws provided with your unit.
8. Using a Phillips screwdriver, place one screw into each of the 10 pilot holes and screw into the
door, as per Fig C. Be careful not to over tighten screws. Ensure the screws sit flush against the
bottom of the channel. Remove clamps from door.
Note: If panel requires additional adjustment after removing clamps, slightly loosen each
screw and adjust panel as necessary. Tighten screws upon completion.
9. Starting at the corners, re-install the gasket into the gasket channel in the frame, by pushing
firmly into place. Make sure the gasket is fully seated into the channel.
HOW TO INSTALLTHE FURNITURE DOOR
1. Fully open door.
2. Starting at the corner, pull the gasket away from the door. As per Fig A.
3. Continue to pull the gasket free from the gasket channel.
4. Upon removal, lay gasket down on a at surface.
5. Secure the furniture door panel to the appliance door using clamps (see Fig. B).
6. Using a 3 mm drill bit, drill 6 pilot holes into the wood panel 12 mm deep using the holes in the
door frame as a guide.
NOT E: It is important to ensure that all drilled holes are drilled to the correct depth in order
to avoid splits in the wood when hardwood is installed. You must also take care not to drill all
the way through the door.
7. Locate 6 of the M4x34 mm screws provided with your unit.
8. Using a Phillips screwdriver, place one screw into each of the 6 pilot holes and screw into the
door, as per Fig C. Be careful not to over tighten screws.
9.Ensure the screws sit ush against the bottom of the channel. Remove clamps from door.
NOTE: If panel requires additional adjustment after removing clamps, slightly loosen each
screw and adjust panel as necessary. Tighten screws upon completion.
10.
Starting at the corners, re-install the gasket into the gasket channel in the frame , by pushing firmly
into place. Make sur e the gasket is fully seatedinto the channel.
Appliance door Furniture door
Bar clamp
NOTE: If a handle is required, please ensure this is installed in an appropriate position before the
furniture door is installed.
Furniture door
HOW TO INSTALLTHE FURNITURE DOOR
1. Fully open door.
2. Starting at the corner, pull the gasket away from the door. As per Fig A.
3. Continue to pull the gasket free from the gasket channel.
4. Upon removal, lay gasket down on a at surface.
5. Secure the furniture door panel to the appliance door using clamps (see Fig. B).
6. Using a 3 mm drill bit, drill 6 pilot holes into the wood panel 12 mm deep using the holes in the
door frame as a guide.
NOT E: It is important to ensure that all drilled holes are drilled to the correct depth in order
to avoid splits in the wood when hardwood is installed. You must also take care not to drill all
the way through the door.
7. Locate 6 of the M4x34 mm screws provided with your unit.
8. Using a Phillips screwdriver, place one screw into each of the 6 pilot holes and screw into the
door, as per Fig C. Be careful not to over tighten screws.
9.Ensure the screws sit ush against the bottom of the channel. Remove clamps from door.
NOTE: If panel requires additional adjustment after removing clamps, slightly loosen each
screw and adjust panel as necessary. Tighten screws upon completion.
10.
Starting at the corners, re-install the gasket into the gasket channel in the frame , by pushing firmly
into place. Make sur e the gasket is fully seatedinto the channel.
Appliance door Furniture door
Bar clamp
NOTE: If a handle is required, please ensure this is installed in an appropriate position before the
furniture door is installed.
Furniture door
Fig. A Fig. B Fig. C

20
Instruction manual WC1800
20 Please keep this instruction manual for future reference
CARE AND MAINTENANCE
CLEANING YOUR WINE CABINET
-Turn off the power, unplug the appliance, and remove all items including the shelves.
-Wash the inside surfaces with a warm water and baking soda solution. The solution should be
about 2 tablespoons of baking soda to 2 pints of water.
-Wash the shelves with a mild detergent solution.
-Wring excess water out of the sponge or cloth when cleaning the area of the controls, or any
electrical parts.
-Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry
with a clean soft cloth.
NOTE: Please take care when cleaning the plinth grille as this may have sharp edges.
TEMPERATURE RECOLLECTION FUNCTION
In the event of a power interruption, the wine cooler will recall the previous temperature settings
once the power is recovered.
TEMPERATURE ALARM
If the internal temperature is higher than 23°C, the display will show “HI” on the appropriate
zone, and the alarm will sound after one hour continuously.
If the internal temperature is lower than 0°C, the display will show “LO” on the appropriate zone,
and the alarm will sound. The malfunction indicator light will also be on at the same time to warn
the consumer.
Check the troubleshooting section to see why the temperature could be fluctuating, and if
necessary, contact Caple service.
OPEN DOOR ALARM
If you forget to close the door or the door is not closed completely, the alarm will sound after 5
minutes. Ensure the door is closed properly to avoid this alarm.
NOTE: If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes before
restarting the unit. If you attempt to restart before this time delay, the Wine Cooler may
not start.
When you use the wine cooler for the first time or restart the wine cooler after having been shut
off for a long time, there could be a few degrees variance between the temperature you select and
the one indicated on the LED display. This is normal and it is due to the length of the activation
time. Once the wine cooler is running for a few hours everything will be back to normal.