Carrier HyperSense 7C-HS-C1W-X User manual

For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-961-01
INTRODUCTION
HyperSense is a subset of HyperStat capable of sensing /monitoring and providing a user
interface for the SmartNode it is connected to. Power and communication are achieved
through the 4-wire cable harness; hence, wiring effort is minimal.
PACKAGE CONTENTS
•HyperSense device
•Mounting accessories
SPECIFICATIONS
Power
Power Source: 6.5 DC input SmartNode
Operating range
Temperature 0 to 122°F (-17 to 50°C)
Humidity 20-85% non-condensing.
Communication
4-wire interface for RS 485 communication @ 9600 baud and 6.5V
DC, 100mA power source
Onboard Sensors
Temperature range of 32 to 122°F with an accuracy of +/-1°F
Humidity 0 to 100% with an accuracy of 2%
CO2 sensor with a range of 0 – 40,000 ppm, accuracy of +/-30ppm (0 -
5000ppm, 25C).
VOC sensor; Typical Accuracy: 15% of measured value; TVOC: 0 - 60,000
ppb.
Occupancy sensor based on passive infrared (PIR) with detection range of 4m
with 15-degree angle
Light Sensor. Ambient light sensor • <100 LUX resolution • High-accuracy UV
index sensor • Matches erythermal curve
Sound sensor with 40-120dB response for 100Hz to 10KHz
PM2.5, PM10 sensor (optional). Detection range of 0-1000µg/m3 and accuracy
of +/-10µg/m3 (PM2.5, 0-100µg/m3) or +/-25µg/m3 (PM10, 0-
100µg/m3). Maximum long-term mass concentration precision limit drift:
•0 to 100 µg/m3 ±1.25 µg/m3/year
•100 to 1000 µg/m3 ±1.25 % mV/year
Inputs
2 x 10K Type-2 thermistor inputs with 2% accuracy
2 x 0-10V Analog voltage inputs with 2% detection accuracy (2-10V)
Touch slider for temperature control along with 3 mechanical buttons
Outputs
2.8" 240x320 pixel TFT display
HyperSense
(7C-HS-C1W-X)
INSTALLATION GUIDE
Scan this QR
code to get a
more detailed
version of the
Installation
Guide

For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-961-01
MOUNTING
1. HyperStat Interface - HyperSense
5. Rubber cover 2
2. HyperStat Main 6. Gang Box
3. Allen head screws
7. PHP screws
4. Rubber cover 1 8. Backplate
PRECAUTIONS
•Failure to wire devices with the correct polarity when using a shared transformer may
result in damage to any device powered by the shared transformer.
•Turn off the power before wiring. Never connect or disconnect the wiring with the
power turned on. Do NOT allow live wires to touch the circuit boards.
•Install in accordance with all state and local codes.
•Do not connect the front to the back plate assembly when the power is ON.
Note: The HyperSense must always
be mounted upright such that you see
the Carrier logo on the top right
Note: The HyperSense must always
be mounted upright such that you see
the Carrier logo on the top right

For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-961-01
1. Place the HyperStat Interface-HyperSense PCB and the back plate (only if the gang box is
fixed vertically) on the gang box such that the back plate covers the gang box and fix
these two items to the wall gang box with the PHP screws provided in the box.
2. Now align the HyperStat main to lock onto the HyperStat Interface- HyperSense PCB.
3. Use the Allen head screws to make this entire setup tamper-proof.
4. Rubber covers 1 and 2 must be fixed to cover the programming pins.
DIS-ASSEMBLING
1. If the HyperSense is mounted on the wall, hold the front plastic with both hands and pull
it away from the wall.
2. If you are holding the HyperSense in your hands, insert a flat head screwdriver in the
notch provided (marked by the two arrows shown in the image) between the front and
back plastic and twist to separate them.
Note
:
•Favorable for Pollution degree 2 or the equivalent •Rated impulse voltage – 330V
•Type action – Type 1. C •Operating Ambient Temperature:
0°C to 50 °C
•The method of connection/disconnection for screwless
terminals is mentioned in the article pointed by the QR
label on the box.
•Indoor Use Only
•Terminal Identification – In the Operating Manual •Powered by Class 2 Power Source

For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-961-01
CARRIER CLIMAVISION TECHNICAL SUPPORT
Installation and servicing of Control Systems can be hazardous due to electrical
components. Only trained and qualified service personnel should install, repair or service
control system components.
For more information on wiring, commissioning, or usage of the ClimaVision product line,
please refer to any documentation provided with the job. If no documentation was provided
with the job, please use the ClimaVision Help Center (support.climavision.com) where you
can find application specific wiring schematics and helpful user guides and videos or scan
the QR code here:
If you need help beyond that, please reach out to your local Carrier distributor for support.
Scan this QR code to
get a more detailed
version of the
Installation Guide