Casio SE-S10 User manual

SE-S10
Electronic Cash Register
EU
UK
DI
START-UP is QUICK and EASY!
Simple to use!
20 departments and 500 PLUs
Automatic Tax Calculations
Calculator function
User's Manual
(SE-S10 small drawer model)
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, Japan

2
E
INTRODUCTION
Thank you very much for purchasing this CASIO electronic cash regis-
ter.
START-UP is QUICK and EASY!
Part-1 of this User's Manual can help you make a quick start.
Once you have mastered the QUICK START operations, you will un-
doubtedly want to expand your use of this machine by studying other
sections of Part-2.
Original Carton/Package
If for any reason, this product is to be returned
to the store where purchased, it must be
packed in the original carton/package.
Location
Locate the Cash register on a flat, stable sur-
face, away from heaters or areas exposed to
direct sunlight, humidity or dust.
Power Supply
Your cash register is designed to operate
on standard household current (120V, 220V,
230V or 240V; 50/60Hz). Do not overload the
outlet by plugging in too many appliances.
Cleaning
Clean the cash register exterior with a soft
cloth which has been moistened with a solu-
tion of a mild neutral detergent and water, and
wrung out.
Be sure that the cloth is thoroughly wrung out
to avoid damage to the printer.
Never use paint thinner, benzene, or other
volatile solvents.
The mains plug on this equipment must be used to disconnect mains power.
Please ensure that the socket outlet is installed near the equipment and shall be easily
accessible.

3
E
INTRODUCTION
Safety precautions
•To use this product safely and correctly, read this manual thoroughly and operate as instructed.
After reading this guide, keep it close at hand for easy reference.
Please keep all informations for future reference.
•Always observe the warnings and cautions indicated on the product.
About the icons
In this guide various icons are used to highlight safe operation of this product and to prevent injury to the operator and
other personnel and also to prevent damage to property and this product. The icons and definitions are given below.
Indicates that there is a risk of severe injury or death if used incorrectly.
Indicates that injury or damage may result if used incorrectly.
Icon examples
To bring attention to risks and possible damage, the following types of icons are used.
The symbol indicates that it includes some symbol for attracting attention (including warning). In this triangle the
actual type of precautions to be taken (electric shock, in this case) is indicated.
The symbol indicates a prohibited action. In this symbol the actual type of prohibited actions (disassembly, in this
case) will be indicated.
The symbol indicates a restriction. In this symbol the type of actual restriction (removal of the power plug from an
outlet, in this case) is indicated.
Warning!
Handling the register
Should the register malfunction, start to emit smoke or a strange odor, or otherwise behave abnormally,
immediately shut down the power and unplug the AC plug from the power outlet. Continued use creates the
danger of fire and electric shock.
• ContactCASIOservicerepresentative.
Do not place containers of liquids near the register and do not allow any foreign matter to get into it. Should
water or other foreign matter get into the register, immediately shut down the power and unplug the AC plug
from the power outlet. Continued use creates the danger of short circuit, fire and electric shock.
• ContactCASIOservicerepresentative.
Should you drop the register and damage it, immediately shut down the power and unplug the AC plug from
the power outlet. Continued use creates the danger of short circuit, fire and electric shock.
• Attemptingtorepairtheregisteryourselfisextremelydangerous.ContactCASIOservicerepresentative.
Never try to take the register apart or modify it in any way. High-voltage components inside the register create
the danger of fire and electric shock.
• ContactCASIOservicerepresentativeforallrepairandmaintenance.
Power plug and AC outlet
Use only a proper AC electric outlet. Use of an outlet with a different voltage from the rating creates the danger
of malfunction, fire, and electric shock. Overloading an electric outlet creates the danger of overheating and
fire.
Make sure the power plug is inserted as far as it will go. Loose plugs create the danger of electric shock,
overheating, and fire.
• Donotusetheregisteriftheplugisdamaged.Neverconnecttoapoweroutletthatisloose.

4
E
INTRODUCTION
Warning!
Use a dry cloth to periodically wipe off any dust built up on the prongs of the plug. Humidity can cause poor
insulation and create the danger of electric shock and fire if dust stays on the prongs.
Do not allow the power cord or plug to become damaged, and never try to modify them in any way. Continued
use of a damaged power cord can cause deterioration of the insulation, exposure of internal wiring, and short
circuit, which creates the danger of electric shock and fire.
• ContactCASIOservicerepresentativewheneverthepowercordorplugrequiresrepairormaintenance.
Caution!
Do not place the register on an unstable or uneven surface. Doing so can cause the register — especially
when the drawer is open — to fall, creating the danger of malfunction, fire, and electric shock.
Do not place the register in the following areas.
• Areaswheretheregisterwillbesubjecttolargeamountsofhumidityordust,ordirectlyexposedtohotorcoldair.
• Areasexposedtodirectsunlight,inaclosemotorvehicle,oranyotherareasubjecttoveryhightemperatures.
The above conditions can cause malfunction, which creates the danger of fire.
Do not overlay bend the power cord, do not allow it to be caught between desks or other furniture, and never
place heavy objects on top of the power cord. Doing so can cause short circuit or breaking of the power cord,
creating the danger of fire and electric shock.
Be sure to grasp the plug when unplugging the power cord from the wall outlet. Pulling on the cord can
damage it, break the wiring, or cause short, creating the danger of fire and electric shock.
Never touch the plug while your hands are wet. Doing so creates the danger of electric shock. Pulling on the
cord can damage it, break the wiring, or cause short, creating the danger of fire and electric shock.
At least once a year, unplug the power plug and use a dry cloth or vacuum cleaner to clear dust from the area
around the prongs of the power plug.
Never use detergent to clean the power cord, especially power plug.
Keep small parts out of the reach of small children to make sure it is not swallowed accidentally.
Disposing of batteries:
Make sure that you dispose of used batteries in accordance with the rules and regulations in your local area.

5
E
Basic Components and Accessories
Contents
Getting to know your cash register .................................................................... 6
Daily Job Flow ................................................................................................... 8
Part-1 QUICK START OPERATION ........................................................... 9
1. Loading Memory Protection Battery ........................................................... 9
2. Loading Paper Roll ..................................................................................... 9
3. Setting the Cash Register........................................................................... 10
4. If you want to use a printer as journal printer ............................................. 10
5. To remove receipt paper ............................................................................. 11
6. To remove journal paper ............................................................................. 11
7. Caution (in handling the thermal printer) .................................................... 11
8. Basic Programming for QUICK START....................................................... 12
9. Basic Operation after Basic Programming.................................................. 14
10. Daily Management Report.......................................................................... 18
Part-2 CONVENIENT OPERATION............................................................ 20
1. Various Programming ................................................................................. 20
2. Various Operations ..................................................................................... 37
Part-3 CALCULATOR FUNCTION ............................................................. 43
1. Calculator Mode.......................................................................................... 43
Part-4 USEFUL INFORMATION ................................................................. 45
1. Troubleshooting .......................................................................................... 45
2. Specifications.............................................................................................. 46
Printer cover
Operator display
Mode switch
Keyboard
Drawer
Accessories
Roll paper 1 pc
Mode keys
Drawer keys 2 pcs
User's manual 1 pc
Fixing hook
(M drawer model only) 2 pcs
Magnetic plate* 1 pc
* Use this plate for tacking the notes
received from customer.
(SE-S10 small drawer model)
Weld lines
Lines may be visible on the exterior of the product. These are “weld lines” that result from the plastic molding process.
They are not cracks or scratches.

6
E
Display
Operator display Customer display
Getting to know your cash register
Note:
An error is gener-
ated (E01 displayed)
whenever the position
of the Mode Switch is
changed during regis-
tration.
The position of the Mode Switch controls the type of operations you
can perform on the cash register. The PROGRAM key (marked PGM)
can be select any Mode Switch setting, while OPERATOR key (marked
OP) can be used to select OFF, REG or CAL only.
OFF
In this position, the power of the cash register is off.
REG (Register)
This is the position used for registration of normal transactions.
RF (Refund)
This is the position used for registration of refunds.
CAL (Calculator)
This is the position used for calculator mode.
PGM (Programming)
This is the position used to program the cash register to suit the
needs of your store.
X (Read)
This is the position used to produce reports of daily sales totals with-
out clearing the totals.
Z (Reset)
This is the position used to produce reports of daily sales totals. This
setting clears the totals.
$Numeric Display
Entered values (unit prices or quantities) and
calculated values (subtotals, totals or change
amount due) are displayed here. The capacity of
the display is 8 digits.
This part of the display can be used to show the
current time or date between registrations (page
40).
%Character Display
In the character programming (P2) mode, it shows
the last entered character.
The total (T) or change (C) appears when a subtotal,
total, or change is obtained.
In the paper saving mode, it shows *.
!Department Number Display
Anytime you press a department key to register a
unit price, the corresponding department number
appears here.
@PLU Number Display
Anytime you perform a PLU registration, the cor-
responding PLU number appears here.
#Number of Repeat Display
Anytime you perform “repeat registration” (page
14), the number of repeats appears here.
Note that only one digit is displayed for the num-
ber of repeats.
OP PGM
!
#
%
@
$
�*12345&78
Getting to know your cash register
Mode Switch
PGM RF OFF REG CAL X Z
OP key ● ● ●
PGM key ● ● ● ● ● ● ●
OP key PGM key
REG
OFF
RF
PGM
XCAL Z
1
2
#
4
12345&78

7
E
Keyboard
7
1
0
4
8
2
00
5
9
3
.
6
FEED PLU
DEPT
SHIFT
ERR.
CORR
—
CHK
NS
#
TAX PGMPAPER
SAVING
POST
RECEIPT
HELP
CLK#
%
AC
=
CA AMT
TEND
C
÷
9/14/19
5
10/15/20
×
6/11/16
7/12/17
−
8/13/18
CH
PD
MRRC
DATE
TIME
×
1
2
3
4
+
SUB TOTAL
1 2 3
E
4 5 6 7
8 9
0 A
B
C
D
G H I J
F
Certain keys have two functions; one for register
mode and one for calculator mode.
In this manual, we will refer to specific keys as
noted below to make the operations as easy to
understand as possible:
Getting to know your cash register
Register Mode
1lFeed key
2
hMultiplication/ Date Time key
3yClear key
4
g Minus/ Error Correction key
5i PLU (Price Look Up) key
6j
Reference Number/Department Shift key
7
:
Percent/Cashier ID No. Assignment key
8.
Received on Account key
9; Paid Out key
0u Charge key
Am Check/No Sale key
BSubtotal key
Cp Cash Amount Tendered key
D?, Z, ~ >, '
Numeric keys and 2-zero key
E"Decimal key
F, , , ,
Department keys
•Department6through20arespeciedby
pressing the jkey respectively as follows:
j ~ j →
Department 6 ~ 10
jj ~ jj →
Department 11 ~ 15
jjj ~ jjj
→
Department 16 ~ 20
G
PAPER
SAVING
Paper saving key
Paper saving key is the key to save printing
paper (Journal compressed printing/ No re
ceipt issuing). In these cases, "
*
" is lit on the
character display.
H
<Post receipt key
Post receipt key is used for issuing receipt
after transaction. This key is effective if the
printer is defined as printing receipts. Refer
to page 38.
I
~Tax Program key
J
/Help key
Help key is used for issuing assistant re-
ceipts such as programming date/ time,
paper installation etc.
Calculator Mode
3t AC key
7:
Percent key
8/ Memory Recall key
Am Drawer Open key
Cp Equal key
D?, Z, ~ >, '
Numeric keys and 2-zero key
E"Decimal key
F, , ,
Arithmetic Operation key

8
E
Daily Job Flow
Before Opening The Store
1. Plugged in?
2. Enough Roll Paper? Page-11
3. Date and Time is correct? Page-40
4. Enough small change in the drawer?
Page-41
While The Store Is Open
1. Registrations. Page-14 ~
2. Issuing latest daily sales total if need-
ed.
(Generating report by Mode Switch to
X position.) Page-18
After Closing The Store
1. Issuing Daily Sales Total.
(Resetting report by Mode Switch to
Z position.) Page-19
2. Picking up money in the drawer.
Page-41.
Turn the Mode Switch to OFF.
Other
1. Troubleshooting Page-45
Daily Job Flow

Part-1
9
E
Part-1 QUICK START OPERATION
QUICK START OPERATION
Part-1
1. Loading Memory Protection Battery
2. Loading Paper Roll
Important
You must initialize
the Cash register.
(Figure 1)
1. Remove the printer cover.
2. Open the battery compartment cover.
3. Load 2 new UM-3, or R6P (SUM-3) type batteries into the
compartment. Be sure that the plus (+) and minus (–) ends
of each battery are facing in the directions indicated by the il-
lustrations inside the battery compartment (Figure 1).
4. Replace the memory protection battery compartment cover
back into place.
·Note:To prevent to lose all of your settings and sales data, we recommend you to install
the memory protection batteries.
·REPLACE MEMORY PROTECTION BATTERIES AT LEAST ONCE EVERY YEAR.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
To load receipt paper
!Open platen arm.
@Ensuring the paper is being fed from the bot-
tom of the roll, lower the roll into the space
behind the paper.
#Put the leading end of the paper over the
printer.
$Close the platen arm slowly until it locks
steadily.

10
E
Part-1 QUICK START OPERATION
3. Setting the Cash Register
!
Plug the power cord of the cash register into AC outlet.
@
Please choose your language followed by printed message.
#
When the display shows blinking "0", such as
Enter current date in Day, Month, Year.
$
When the display shows blinking "0", such as
Enter current time in Hour, Minute.
%
Set the mode switch to REG.
^
Tear off any excess paper.
&
Replace the printer cover slowly.
*Default printer definition is receipt printer.
00-00-00
00-00
4. If you want to use a printer as journal printer
!
Set printing system as journal.
Z
Zu
@
Remove the printer cover by lifting up the back.
#
Press the
l
key until approximately 20cm of the
paper is fed from the register.
REG
OFF
RF
PGM
CAL X Z
$
Roll the paper onto the take up real a few turns.
%
Set the left plate of the take up need and place the
reel into the register.
^
Press the
l
key to take up any slack in the pa-
per.
&
Replace the printer cover slowly.

Part-1
11
E
Part-1 QUICK START OPERATION
5. To remove receipt paper
!
Open the platen arm.
@
Remove the core of the paper.
6. To remove journal paper
!Remove the printer cover by
lifting up the back.
@Press the lkey until ap-
proximately 20cm of the pa-
per is fed from the printer.
#Cut off the roll paper.
$Remove the take-up reel
from the printer and take off
the left plate of the reel.
%Remove the journal paper
from the take-up reel.
^Open the platen arm.
&
Remove the core of the pa-
per.
*Load new paper following the
instructions "1. To load jour-
nal paper".
7. Caution (in handling the thermal printer)
1. Never touch the printer head and platen.
2. Unpack the paper just before you use.
3. Avoid heat/ direct sunlight.
4. Avoid dusty and humid places for strage.
5. Do not scratch the paper.
6. Do not keep the paper under the following circumstances: High humidity and temperature/ direct
sunlight/ contact with glue, thinner or rubber eraser.

12
E
Part-1 QUICK START OPERATION
8. Basic Programming for QUICK START
Mode Switch
REG
OFF
RF
PGM
CAL X Z
Procedure Purpose
1. To select the date format and monetary mode (if necessary)
You can select the date format and monetary mode after initialization depending on
the requirements in your area. Default date format is Day/ Month/ Year and default
monetary mode is add 2.
C
?ZXX
X?p
Date Format Selections
A
Year/ Month/ Day ?
Day/ Month/ Year Z
Month/ Day/ Year X
Monetary Mode Selections
B
Add 0 (0.) ?
Add 1 (0.0) Z
Add 2 (0.00) X
Select number from list B
(To end the setting)
P3 appears in mode display
Program set code No.
Select number from list A
Select date format
and
monetary mode
2. Input the desired add-in tax rate to the appropriate department key.
(This procedure below programs add-in tax rate only. If you want to set add-on tax
or tax with special rounding, refer to page 27 of this manual.)
A) Enter
1
and press the key.
B) Press the
~
key.
C) Enter tax rate. (Example: For 6% enter “6”, 5.75% enter “5.75”.)
D) Press the appropriate department key.
E) Repeat step B) and C) to set other department key.
F) Press the key to end tax programming.
Note: In case of setting the wrong tax rate to the key, please enter ?and press
those department keys above, and quit this procedure by pressing key,
and start from the beginning of this procedure.
Setting the tax rates
Example :
Set add-in tax 8% to department 2, 3, 15% to department 4 key.
~
Start tax program.
8
Enter tax rate and press dept key.
8
Enter tax rate and press dept key.
15
Enter tax rate and press dept key.
To end the setting.

Part-1
13
E
Part-1 QUICK START OPERATION
Procedure Purpose
3. In case of accepting two (the Euro and the local) currencies.
3-1. Press the following keys to define the main currency/print out currency of the
subtotal.
P3 appears in mode display
C
XVXX
Z p
Euro Status
(to end the setting)
Euro status
(1) Main currency = Local, Print out subtotal = Local: ?
(2) Main currency = Euro, Print out subtotal = Euro : Z
(3) Main currency = Local, Print out subtotal = Both: X
(4) Main currency = Euro, Print out subtotal = Both : C
3-2. Press the following keys to set the currency exchange rate against the Euro.
Example: (Exchange rate and decimal position)
Currency exchange rate = 1 Euro in local currency
1 Euro = 1.95583 DM : Z>BB<CB
Z
Z"B>;

P appears in mode display
•The rate within the range of 0.00001 to 999999.
(To end the setting)
Setting the Euro
4. In case of becoming to accept the Euro only.
You can restrict the registable currency to the Euro only by the following procedure.
1. Turn the mode switch to Z position.
2. Issue all reset report including periodic data.
3. Press the following keys to set.
?Z?MX??X p
If you want to cancel this operation, press instead of p.
Restricting the Cur-
rency
to the Euro
5.For Australia only.
You can set some programmable options to suit the Australian GST by the following
procedure.
1. Turn the mode switch to Z position.
2. Press the following keys to program. ?Z?ZX??Z p
If you want to cancel this operation, press instead of p.
Setting the
Australian GST

14
E
Part-1 QUICK START OPERATION
Z??
jX??
jjC?
B?? p
REG
OFF
RF
PGM
CAL
Z
X
9. Basic Operation after Basic Programming
Whenever an error is generated, the input figures reset to 0. All printout
samples are journal images and the header (date, time and consecutive
no.) are eliminated from the samples.
Mode Switch
9-1 Open the drawer
without a sale
Note:
9-2 Basic operation
m
Printout
Operation
Unit Price Department 1
Cash amount tendered
Z??
C h
ZCB
p
9-3 Multiple registra-
tion of the same
items
Multiple key
Department 1
Unit Price
Quantity
Note that repeat registration can be used with unit prices up to 6 digits long.
9-4 Charge sales
Z??
X??
C??
u
Charge key
You cannot perform the amount tendered operation using the ukey.
08-01-2010 08:55
REG 0001
NS ••••••••••— No Sale Symbol
—
Department No./Unit Price
— Subtotal
— Cash Amount Tendered
— Change Amount Due
08-01-2010 09:00
REG 0002
DEPT01 •1.00
DEPT10 •2.00
DEPT15 •0.30
TOTAL •
3 . 30
CASH •5.00
CHANGE •1.70
— Repeat
— Sales Quantity/ Unit Price
08-01-2010 09:05
REG 0003
DEPT01 •1.00
DEPT01 •1.00
3X@1.35
DEPT02 •4.05
CASH •
6 . 05
— Charge Sales
08-01-2010 09:10
REG 0004
DEPT01 •1.00
DEPT02 •2.00
DEPT01 •3.00
CHARGE •
6 . 00
Example
Unit Price $1.00 $2.00 $0.30
Quantity 1 1 1
Dept. 1 10 15
Cash
Amount
tendered
$5.00
Example
Unit Price $1.00 $1.35
Quantity 2 3
Dept. 1 2
Example
Unit Price $1.00 $2.00 $3.00
Quantity 1 1 1
Dept. 1 2 1
Department 10
Departments 6 through 10, 11 through 15, 16 through 20 can also be regis-
tered in combination with the jand , , , or keys, respec-
tively. The jkey should be entered just before entering unit price manually.
Department 15

Part-1
15
E
Part-1 QUICK START OPERATION
V?? y
Z??
X??
h
y
B h
X??
Printout
Operation
9-5 Split cash/
charge sales
X??
C??
V??
B??p
u
Z?h
ZB?y
Z?h
Z?B
9-6 Corrections
Corrections can be made while you are registering the item (before
you press a department key), or after it has already been regis-
tered into the memory (by pressing a department key).
9-6-1 Before you
press a depart-
ment key
ykey clears the last item entered.
2. Entered unit price first
instead of quantity
and then pressed h.
Example
1. Entered 400 for unit
price by mistake in-
stead of 100.
Operation Printout
Wrong entry Clears the last item entered.
Correct entry Registered Department 1
Unit price Multiplication
Multiplication
Registered Department 2
Clears the last item entered.
Quantity
Unit price
3. Entered 150 for unit
price by mistake in-
stead of 105.
Quantity
Quantity
Wrong entry Clears the last item entered.
Correct entry Registered Department 3
Multiplication
— Cash Amount Tendered
— Charge Sales
08-01-2010 09:25
REG 0005
DEPT01 •2.00
DEPT02 •3.00
DEPT01 •4.00
TOTAL •
9 . 00
CASH •5.00
CHARGE •4.00
DEPT01 •1.00
5X@2.00
DEPT02 •10.00
10X@1.05
DEPT03 •10.50
Example
Unit Price $2.00 $3.00 $4.00
Quantity 1 1 1
Dept. 1 2 1
Cash
Amount
tendered
$5.00

16
E
Part-1 QUICK START OPERATION
BB?
g
B?B
Ch
XX?
g
Ch
XC?
REG
OFF
RF
PGM
CAL
Z
X
Mode Switch
gkey cancels the last registered item.
9-6-2 After you
pressed a
department key
Example
1. Entered unit price 550 by
mistake instead of 505 and
pressed a department key.
Operation Printout
Wrong entry
Registered Department 1Correct entry
Cancels the last item registered.
2. Entered unit price 220 by
mistake instead of 230
and pressed a depart-
ment key.
MultiplicationQuantity
Cancels the last item registered.
Wrong entry
Correct entry Registered Department 2
DEPT01 •5.50
ERRCORR -5.50
DEPT01 •5.05
3x@2.20
DEPT02 •6.60
ERRCORR -6.60
3X@2.30
DEPT02 •6.90

Part-1
17
E
Part-1 QUICK START OPERATION
C h
X??
;
Z?'
;
p
REG
OFF
RF
PGM
CAL
Z
X
Mode Switch
9-7 Registering with
currency exchange
Display
Operation
Pressing ]before subtotal converts the
subtotal amount into the Euro.
— Subtotal in the main currency
— Subtotal after conversion
— Payment in the Euro
— Payment after conversion
— Change in the main currency
— Change in the sub currency
08-01-2010 09:30
REG 0010
3x@2.00
DEPT01 •6.00
TOTAL •
6 . 00
⁄
7 . 50
EURO
CASH ⁄10.00
CASH •8.00
CHANGE •2.00
EURO CG ⁄2.50
Printout
Pressing ;after amount tendered
converts the amount into the Euro. *1
Press pto finalize the transaction.
The change amount in the main currency
is shown on the display. *2
*1 If the payment is the same as the subtotal amount, you can omit this
operation. Press pkey directly after the subtotal.
*2 If the payment is less than the subtotal amount, the cash register
specifies it as a partial payment and shows the balance in the main
currency on the display.
'50e
1~00e
"00
Example
Unit Price £2.00
Quantity 3
Dept. 1 1
Cash Amount
tendered 10.00 Euro
Rate 1Euro = £ 0.8
Main currency Local (£)
Printout of ST Both currencies

18
E
Part-1 QUICK START OPERATION
10. Daily Management Report
This section tells you the procedures to use to produce reports of the transaction data stored in the
cash register's memory.
Important
Remember that when you issue a reset (Z) report, the data that is reported is cleared from
the applicable totalizers. To view data without clearing totalizers, issue a read (X) report.
10-1 Financial Report
Printout
Operation
REG
OFF
RF
PGM
CAL Z
X
Mode Switch
10-2 Read/Reset
Report
h
— Read Symbol
— Gross Sales No. of items
— Gross Sales Amount
— Net Sales No. of Customers
— Net Sales Amount
— Cash Total in Drawer
— Charge Total in Drawer
— Check Total in Drawer
08-01-2010 19:10
X 0070
FLASH X
GROSSTOTAL QT57
 •270.48
NETTOTAL No38
 •271.24
CASH-INDW •197.57
CHARGE-INDW •18.19
CHECK-INDW •45.18
10-2-1 Electronic
journal Report
Mode Switch to
X
Printout
Operation
B<p
(Date)*
p
(Consecutive No.)*
p
— Read Symbol
— Journal
10-01-2010 19:25
X 0173
0058 EJ X
REG 17:34
 0023
DEPT01 •2.24
CA •
2 . 24
* If you want to designate read range, enter date and/ or cosecutive No..
If you want to reset the electronic journal, just press B<pin Z mode.
• Journal is saved in the memory and you can take a report any time you want.

Part-1
19
E
Part-1 QUICK START OPERATION
X (Read) report is the same except *1 and *2.
10-2-3 Periodic Read/
Reset Report
Mode Switch to
Z
or
X
Printout
Operation
Z?p
— Periocic Reset Symbol
— Gross Sales No. of Items
— Gross Sales Amount
— Net Sales No. of Customers
— Net Sales Amount
12-01-2010 20:25
Z 1100
0010 PERIODIC ZZ 0001
GROSSTOTAL QT67
 •270.73
NETTOTAL No38
 •271.24
Mode Switch to
X
(Read)
Mode Switch to
Z
(Reset)
10-2-2 Daily Read/Reset
Report
Printout
Operation
p
Z (Reset) report
p
— Date/ Time
— Consecutive No.
—
Non-resettable No. of
Resets
*1
/RESET Symbol
*1
— Dept. Name/ No. of Items
— Amount
— Gross Sales No. of Items
— Gross Sales Amount
— Net Sales No. of Customers
— Net Sales Amount
— Cash in Drawer
— Charge in Drawer
— Check in Drawer
— Taxable Amount for Tax Rate 1
— Tax Amount for Tax Rate 1
— Rounded Amount
— Refnd Mode Count
— Refund Mode Amount
— No. of pkey operation in CAL mode
— Cash Sales Count
— Cash Sales Amount
— Charge Sales Count
— Charge Sales Amount
— Check Sales Count
— Check Sales Amount
— Received On Account Amount
— Paid Out Amount
— Reduction Amount
— Premium/Discount Amount
— Error Correction Count
— No sale Count
— Clerk 1 Sales Amount
(Refer to 2-8 Cashier Assignment)
— Non-resettable Grand Sales total
(Printed only on RESET report) *2
08-01-2010 19:25
Z 0073
0000 DAILY Z 0012
DEPT01QT 48
 •50.10
DEPT02 QT 28
 •76.40
DEPT03QT 17
 •85.80
DEPT20QT 4
 •3.00
------------------------
GROSS TOTAL QT 108
 •316.80
NETTOTAL No46
 •325.13
CASH-INDW •199.91
CHARGE-INDW •16.22
CHECK-INDW •105.00
TA1 •105.10
TAX1 •4.20
ROUNDINGAMT •1.23
RF-MODE TTL No 2
 •0.50
CALCULATOR No3
------------------------
CASH No44
 •203.91
CHARGE No3
 •16.22
CHECK No 2
 •105.00
RC •6.00
PD •10.00
- •0.50
%- •0.66
ERR CORR No 21
NS No 12
------------------------
CLERK01 •325.13
------------------------
GT •0,000,832,271.20
REG
OFF
RF
Z
CAL X
PGM
Mode Switch

20
E
Part-2 CONVENIENT OPERATION
CONVENIENT OPERATION
Part 2
Mode Switch
(For Dept. 1)
(For Dept. 2)
(For Dept .3)
P appears in mode display
P appears in mode display
Z
Z??
XX?
ZZ??
Z
X"B :
(To end the setting)
•Unitpriceswithintherangeof0.01~9999.99.
•Theratewithintherangeof0.01to99.99%.
Z ~
.
j;
TaxstatusfortheDepartments1~20areinitializedasNon-Tax-
able.
P appears in mode display
(To end the setting)
REG
OFF
RF
PGM
CAL X Z
SelectkeyfromlistA For Dept. 1
Taxable status 2 For Dept. 7
Selections
Taxable status 1 .
A
Taxable status 2 ;
Taxable status 3 h
Taxable status 4 u
Non-taxablestatus m
Example
UnitPrice $1.00 $2.20 $11.00
Dept. 1 2 3
1. Various Programming
1-1 Unit price for Departments
1-2 Rate for percent key
1-3 To change tax status
for Departments
Example
DiscountRate 2.5%
Example
Status Taxable 1 Taxable 2
Depts. 1 7