CB2 ASH User manual

Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Made in Vietnam - r04 Page 1 of 4
ash BATH CABINET
assembly hardware
wall mounting hardware
tools required
Thank you for purchasing the Ash Bath Cabinet.
This page lists all the contents included in the box.
Please take the time to identify the hardware as well
as the individual components to this product. As you
unpack and prepare for assembly, place the contents
on a carpeted or padded area to protect them from
damage.
Note: 2 people are recommended to safely assemble this product.
Missing hardware?
Please call 800.606.6387 for replacements.
A. Insert 4 cam screws into left and right side
panels as shown. Secure, but do not over tighten,
cam screws with a phillips head screwdriver.
B. Insert 2 cams into left and right side panels as
shown. Make sure arrows on cams point towards
nearest edge with holes.
12 - cam
screws
12 - cams 8 - shelf
supports
1 - top
panel
2 - doors
2 - adjustable
shelves
1 - leg assembly
1 - side panels
(1 left, 1 right)
1 - back
panel
phillips head screwdriver
NOTE: Do not over
tighten the cam screws
right side
panel
1
components
(We recommend the use of hand tools instead of power tools)
left side
panel
A
B
NOTE: Make sure arrows
on cams point towards
nearest edge with holes
2 - plastic
anchors
2 - screws
FACING INSIDE

leg assembly back panel
top panel
Insert 4 cam screws into leg assembly as
shown.
A. Insert 4 cams into top panel as shown.
B. Insert 4 cams into back panel as shown.
B
A
ash BATH CABINET
Made in Vietnam - r04 Page 2 of 4
4 5
2 3
Fit dowels of top panel into left side panel as
shown and secure cams.
A. Fit pre-assembled dowels of back panel into
corresponding holes of left side panel as
shown.
B. Using a screwdriver, turn each cam clock-
wise until it securely engages each cam screw.
A
B
back panel
back panel
left side
panel
back panel
top
panel
left side
panel
FACING INSIDE
NOTE: Make sure
label, “Facing Inside,”
on back panel is
positioned as shown
during assembly
FACING INSIDE
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

ash BATH CABINET
Fit dowels of top panel into corresponding holes
of right side panel and secure cams.
Made in Vietnam - r04 Page 3 of 4
89
6 7
With the assistance of another adult, fit dowels
of side panels into corresponding holes of leg
assembly and secure cams.
Fit hinges of each door onto corresponding
hinges of side panels and tighten with
pre-attached screw, using a screwdriver.
right side
panel
leg
assembly
door
WALL
Determine the final location of unit. With the
assistance of another adult, position unit upright
against wall and mark the 2 holes position in the
back panel. Set unit aside. Drill a hole in the wall
stud. If a wall stud is not available, drill a hole in the
wall that is slightly smaller in diameter than the
anchor. Gently tap the plastic anchors until the
flange of the anchor is flush with the wall. Align
holes of wall and unit. Insert 2 large screws
through the back panel and into the wall anchor in
the wall.
Refer to Hinge Adjustment
diagram for adjusting the
alignment of the door hinges.
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com

ash BATH CABINET
Made in Vietnam - r04 Page 4 of 4
cleaning & care
Clean surfaces with a dry or damp soft cloth. Do not use
abrasive cleaners. Do not use furniture wax or polish as
the unit is finished with a protective clear lacquer.
hinge adjustment
If the doors do not appear square or aligned,loosen or tighten the appropriate screws on each case hinge as illustrated.
Depth adjustment:
Loosen screw A, push hinge arm
forwards or backwards, re-tighten
screw Aand secure screw Bwith
a 1/4 turn clockwise
Height adjustment:
Loosen screw C, adjust door
height and re-tighten screw C
1 2 3
Side to side adjustment:
Loosen screw A, adjust gap with
screw Band re-tighten screw A
10
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
A. Insert 8 shelf supports into side panels as
shown.
B. Place 2 adjustable shelves onto shelf
supports. Make sure each shelf is securely
supported by shelf supports.
Assembly is now complete.
A
A
B
adjustable shelf
A
B
AC
C
B