Celexon Professional Plus User manual

Operating instructions
celexon Electric Professional Plus
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully
before connecting or operating this product. Please retain these instructions for future
reference.
Version: 32422_061

1
The purpose of these operating instructions is to familiarise you with the operation of
this product. Therefore, keep these instructions in a safe place so that you can refer to
it at any time.
• Before installation, please refer to the enclosed data sheet for further safety and use
instructions.
• Do not begin installation until you have read and understood the complete
operating instructions.
• Carry out the installation with another person to ensure safe installation.
• Remove the product from its packaging and remove all packaging material.
Make sure that there is no packaging material on or in the product. If you notice
any damage to the packaging, also check whether there is any damage to the
product. If you notice any external damage to the unit or any unexpected or
unusual functioning, the product must not be used any further. Immediately
contact the dealer from whom you purchased the product or celexon directly
(Web: www.celexon.co.uk, Mail: [e-mail]) for further information.
• To ensure trouble-free operation, the product may only be used indoors. It is NOT
suitable for outdoor use.
• The use of the appliance and accessories is forbidden to children under 16 years of
age.
• Ensure that no children play with the appliance or are in the vicinity without
supervision.
• Conversion or modication of the product impairs product safety.
• Caution: Risk of injury! Never open the product without authorisation. Never carry
out repair yourself!
• Do not use the product near gas or water appliances or in a dusty environment.
• Handle the product with care. It can be damaged by knocks, blows or falling from
even a small height.
• Keep the product away from moisture and heat.
• Never immerse the product in water or other liquids.
• Use the product only in its intended manner. Use for any other purpose may
damage the product or its surroundings.
• Tighten the screws, but do not overtighten them. Overtightening the screws (e.g.
by using a cordless screwdriver) can cause damage and affect the secure hold of
the screen.
WARNINGS

2
• Suspended loads must be checked for strength and load-bearing capacity at least
twice a year.
• Children should not use the screen or play under it unsupervised.
• Caution: Risk of injury! The unit closes ush and rmly in its retracted state, keep
ngers, hands or other small parts away from the opening.
• All supply lines and cables must not be subjected to additional loads and must be
laid in such a way that they are not damaged or crushed.
• Failure to observe the above instructions may result in personal injury and damage
to the product or equipment connected to it. Incorrect installation or use may also
invalidate the warranty.
• If you are unsure about the use of the product, please contact specialist personnel,
your dealer or celexon directly (Web: www.celexon.co.uk, Mail: [e-mail]).
• Technical changes and errors expected.
The manufacturer accepts no responsibility for damage to property or personal injury,
if the screen is used outside the recommended specications, or in the event of improper
installation. Do not use this screen in the vicinity of heaters or air conditioners. Also, do
not mount the product in direct sunlight or in front of a window. Due to the tempera-
ture-sensitive PVC surface, the projection screen fabric may be permanently damaged.
We recommend that you wait approx. 2 hours after delivery before installing the projecti-
on screen. This way you will allow the screen to acclimatise, especially when moving from
a cold to a warm environment (or vice versa).
Please avoid any stains on the surface of the screen. These may not be able to be remo-
ved.
The positions of the end points are already optimally set at the factory and should not be
changed. Especially with electric screens, the entire length of the fabric should always be
used in order to achieve the best atness. An adjustment of a few cm of the end points
should only be made by persons with specialist knowledge and in consultation with the
manufacturer. Incorrect adjustment can result in damage to the projection surface.

3
Voltage: 100 V ~ 120 V, 60 Hz
220 V ~ 240 V, 50 Hz
Consumption: 130 W (MAX)
0,4 W (Standby)
Control: External infrared control box
with remote control
TECHNICAL DATA
DISCLAIMER
The information in this document is subject to change without notice by the
manufacturer. Changes will be added to subsequent versions of this manual.
Errors expected.
CARE INSTRUCTIONS
NEVER clean the screen with alcohol or other cleaning agents containing
solvents. Use only a soft and clean cloth. If necessary, dirt can be removed
from the surface with a mild soap solution (max. 5%). It is essential to avoid
contact with pointed or sharp objects. These could permanently damage the
projection screen fabric. Further instructions can be found in the enclosed
projection screen instructions.

4
IN THE BOX
INSTALLATION NOTES
1x Screen 4x Plastic dowels 4x Screws 1x IR remote control incl.
Batteries
Measure the distance between the
eyelets. Mark the points on the
ceiling and make sure that the eyelets
are aligned with each other and parallel
to the wall.
MOUNTING ON THE CEILING (VIA EYELETS)
Install the screen in a position that is fully visible to all viewers! The optimum
installation height corresponds to the position of the viewers in the centre of
the screen with the screen fabric extended: eye level = lower third of the screen
surface.
The screen can be installed on the wall/ceiling or hung from the ceiling on
closed ring eyelets plus screwable karabiners (not included). The eyelets are
already on the side cap - for screwed wall or ceiling mounting only, the eyelets
must be removed beforehand. Please ensure that the metal plates are also
used for wall and ceiling mounting as otherwise a safe installation cannot be
guaranteed. The enclosed mounting material is intended for a solid stone wall,
if necessary obtain suitable mounting material for your installation surface.

5
Measure the distance between the
holes in the side caps (two per cap)
and transfer them to the ceiling. Drill
the holes at the markings to the right
diameter for the mounting material,
insert and screw the screen in place
tightly. Make sure that the holes are
parallel to the wall.
Use dowels and screws suitable for
your surface.
Caution: Do not overtighten the
screws! If you notice cracks in the caps
they must be replaced! The screen
must not be used with cracked caps.
Please ensure that the metal plates are
also used for wall and ceiling mounting,
otherwise a safe installation cannot be
guaranteed).
Drill the holes at the markings at a
diameter to match the diameter of
the ring eyelet used, screw them
 rmly into the ceiling (according to the
manufacturer‘s instructions and the
load capacity of the screen) and hang
the screen.
MOUNTING ON THE CEILING (SCREWED)

6
MOUNTING ON THE WALL
Measure the distance between the
holes in the side caps (two per cap)
and transfer them to the wall.
Drill the holes at the markings with the
holes with the right diameter for the
mounting material and make sure that
the drill holes are absolutely level (Use
a spirit level!).
Use dowels and screws that are suitab-
le for your mounting surface. Screw the
two upper screws into the wall most
of the way and hang the screen from
both sides into the upper hole. Make
sure that the screen is installed straight
and level. Tighten the screws and then
tighten the lower screws on both sides
of the screen.
Caution Do not overtighten the screws!
If you notice cracks in the caps they
must be replaced! The screen must not
be used with cracked caps. Please en-
sure that the metal shims are also used
for wall and ceiling mounting, other-
wise a safe installation cannot be gu-
aranteed).

7
OPERATION
STEP 1: SAFETY CHECK (FIG. 1)
STEP 3: RETRACT SCREEN (FIG. 3)
Insert the plug into the socket (ensure correct voltage). The cable must not be
laid on hot surfaces or stretched. When using an extension make sure it has
the correct speci cation. The wall control box must be mounted with the cable
outlet on the underside.
Press the arrow key pointing upwards.
The screen retracts and stops auto-
matically at the housing or the set up-
per end point. Make sure that no ob-
jects or persons obstruct the retraction
of the screen.
CONTROL VIA THE WALL CONTROL BOX
STEP 2: EXTEND THE SCREEN (FIG. 2)
Press the downward pointing arrow
button. The screen extends and stops
automatically at the set end point.
Make sure that no objects or persons
obstruct the extension path of the
screen
STEP 4: STOP THE SCREEN
To stop the screen manually, press the stop button between the arrows.

8
CONTROL VIA THE REMOTE CONTROL
STEP 1: SAFETY CHECK (FIG. 1)
Insert the plug into the socket (ensure correct voltage). The cable must not
be laid on hot surfaces or stretched. When using an extension make sure it
has the correct speci cation. The wall control box must be mounted with the
cable outlet on the underside.Make sure that there is a line of sight between
the wall control box and the remote control. The IR eye on the box must not
be covered.
STEP 3: RETRACT THE SCREEN (FIG. 3)
Press the upward pointing arrow but-
ton. The screen retracts and stops au-
tomatically at the housing or the set
upper end point.Make sure that no
objects or persons obstruct the
retraction of the screen.
STEP 2: EXTEND THE SCREEN (FIG. 2)
Press the downward pointing arrow
button. The screen extends and stops
automatically at the set end point.
Make sure that no objects or persons
obstruct the extension path of the
screen
STEP 4: STOP THE SCREEN
To stop the screen manually, press the stop button between the arrows.
It is possible to set the stop points. Please request the instructions for this procedure from
your specialist dealer or directly via www.celexon.com.

9
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon Electric Professional Plus
Products that are marked with the CE mark meet all requirements of the relevant
EU directives. The EU declaration of conformity can be downloaded from the
following address: www.celexon.de/zertikate
INFORMATION ON EU CONFORMITY
The symbol indicates the separate collection of electrical and electronic
devices in EU countries. Please do not throw the device into household
waste. Find out about the return system applicable in your country and
contact your local authority or your local waste and pollutant collection
point if you have any questions about the disposal process.

10
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon Electric Professional Plus
Products that are marked with the UKCA mark meet all requirements of the re-
levant UK directives. The UK declaration of conformity can be downloaded from
the following address: www.celexon.de/zertikate
INFORMATION ON UK CONFORMITY
The symbol indicates the separate collection of electrical and electronic
devices in EU countries. Please do not throw the device into household
waste. Find out about the return system applicable in your country and
contact your local authority or your local waste and pollutant collection
point if you have any questions about the disposal process.