Celexon Expert User manual

Operating instructions
celexon Electric Expert and
Expert XL
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully
before connecting or operating this product. Please retain these instructions for future
reference.
Version: 32422_061

1
The purpose of these operating instructions is to familiarise you with the operation of
this product. Therefore, keep these instructions in a safe place so that you can refer to
it at any time.
• Before installation, please refer to the enclosed data sheet for further safety and use
instructions.
• Do not begin installation until you have read and understood the complete
operating instructions.
• Carry out the installation with another person to ensure safe installation.
• Remove the product from its packaging and remove all packaging material.
Make sure that there is no packaging material on or in the product. If you notice
any damage to the packaging, also check whether there is any damage to the
product. If you notice any external damage to the unit or any unexpected or
unusual functioning, the product must not be used any further. Immediately
contact the dealer from whom you purchased the product or celexon directly
(Web: www.celexon.co.uk, Mail: [e-mail]) for further information.
• To ensure trouble-free operation, the product may only be used indoors. It is NOT
suitable for outdoor use.
• The use of the appliance and accessories is forbidden to children under 16 years of
age.
• Ensure that no children play with the appliance or are in the vicinity without
supervision.
• Conversion or modication of the product impairs product safety.
• Caution: Risk of injury! Never open the product without authorisation. Never carry
out repair yourself!
• Do not use the product near gas or water appliances or in a dusty environment.
• Handle the product with care. It can be damaged by knocks, blows or falling from
even a small height.
• Keep the product away from moisture and heat.
• Never immerse the product in water or other liquids.
• Use the product only in its intended manner. Use for any other purpose may damage
the product or its surroundings.
• Tighten the screws, but do not overtighten them. Overtightening the screws (e.g.
by using a cordless screwdriver) can cause damage and affect the secure hold of
the screen.
WARNINGS

2
• Suspended loads must be checked for strength and load-bearing capacity at least
twice a year.
• Children should not use the screen or play under it unsupervised.
• Caution: Risk of injury! The unit closes ush and rmly in its retracted state, keep
ngers, hands or other small parts away from the opening.
• All supply lines and cables must not be subjected to additional loads and must be
laid in such a way that they are not damaged or crushed.
• Failure to observe the above instructions may result in personal injury and damage
to the product or equipment connected to it. Incorrect installation or use may also
invalidate the warranty.
• If you are unsure about the use of the product, please contact specialist personnel,
your dealer or celexon directly (Web: www.celexon.co.uk, Mail: [e-mail]).
• Technical changes and errors expected.
The manufacturer accepts no responsibility for damage to property or personal
injury, if the screen is used outside the recommended specications, or in the event of
improper installation. Do not use this screen in the vicinity of heaters or air conditioners.
Also, do not mount the product in direct sunlight or in front of a window. Due to the
temperature-sensitive PVC surface, the projection screen fabric may be permanently
damaged.
We recommend that you wait approx. 2 hours after delivery before installing the
projection screen. This way you will allow the screen to acclimatise, especially when
moving from a cold to a warm environment (or vice versa).
Please avoid any stains on the surface of the screen. These may not be able to be
removed.
The positions of the end points are already optimally set at the factory and should not
be changed. Especially with electric screens, the entire length of the fabric should always
be used in order to achieve the best atness. An adjustment of a few cm of the end points
should only be made by persons with specialist knowledge and in consultation with the
manufacturer. Incorrect adjustment can result in damage to the projection surface.

3
Voltage: 100 V ~120 V, 60 Hz
220 V ~ 240 V, 50 Hz
Consumption: 156 W (MAX)
0,4 W (Standby)
TECHNICAL DATA
DISCLAIMER
The information in this document is subject to change without notice by the
manufacturer. Changes will be added to subsequent versions of this manual.
Errors expected.
CARE INSTRUCTIONS
NEVER clean the screen with alcohol or other cleaning agents containing
solvents. Use only a soft and clean cloth. If necessary, dirt can be removed
from the surface with a mild soap solution (max. 5%). It is essential to avoid
contact with pointed or sharp objects. These could permanently damage the
projection screen fabric. Further instructions can be found in the enclosed
projection screen instructions.

4
IN THE BOX
Install the screen in a position that is fully visible to all viewers! The optimum
installation height corresponds to the position of the viewers in the centre of
the screen with the screen fabric extended: eye level = lower third of the screen
surface.
The screen can be installed on the wall or ceiling. Obtain suitable mounting
material for your installation surface.
INSTALLATION NOTES
Measure the distance between the mounting brackets. The brackets should
each be installed evenly along the housing.
Transfer the measurement to the mounting surface. Ensure that the holes are
parallel. Pre-drill the holes at the markings in the appropriate diameter for the
mounting material, insert them and screw on the brackets.
1x Screen Mounting bracket
Motor Expert (2x)
Motor Expert XL (4x)
1 x Wall switch
MOUNTING ON THE CEILING / WALL
STEP 1

5
Lift the screen (with 2 people) and hook the casing rstly into the rear guide
of the bracket with a slight turn and then x the casing to the bracket from
the front with the locking screws. Do not release the housing until the locking
screw has connected the housing and the bracket together.
Remove the transport protection between the weighted rod and the housing.
Finally, check the screws on the screen and tighten them if necessary. In the
event of damage to the brackets or the safety screws, please contact your
dealer. The screen may only be used after the defective components have been
replaced.
A = Expert 9,5cm | Expert XL 12,4cm
B = Expert 2,7cm | Expert XL 1,6cm
C = Expert 11,5cm | Expert XL 13,3cm
STEP 2

6
OPERATION
The electrical connection of the screen must be carried out by quali ed
personnel according to the technical data (see above). Mount the wall switch
near the screen so that the user always has the screen in view when extending
and retracting it.
The cable must not be laid on hot surfaces or stretched. Never connect the wall
switch to more than one device. Disconnect the screen during maintenance
work.
STEP 1: SECURITY CHECK & CONNECTION
STEP 3: RETRACT THE SCREEN (FIG. 3)
Press and hold the button marked with
the up arrow. The screen retracts and
stops automatically at the housing or
the set upper end point. Make sure
that no objects or persons obstruct the
retraction.
STEP 2: EXTEND THE SCREEN (FIG. 2)
Press and hold the button marked with
the down arrow. The screen extends
and stops automatically at the set end
point. Make sure that no objects or
persons obstruct the extension of the
screen.
STEP 4: STOP THE SCREEN
To stop the projection screen manually, release the pressed button - the screen
stops immediately.
It is possible to set the stop points. Please request the instructions for this procedure from
your specialist dealer or directly via www.celexon.com

7
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon Electric Expert and Expert XL
Products that are marked with the CE mark meet all requirements of the relevant
EU directives. The EU declaration of conformity can be downloaded from the
following address: www.celexon.de/zertikate
INFORMATION ON EU CONFORMITY
The symbol indicates the separate collection of electrical and electronic
devices in EU countries. Please do not throw the device into household
waste. Find out about the return system applicable in your country and
contact your local authority or your local waste and pollutant collection
point if you have any questions about the disposal process.

8
Manufacturer: celexon Europe GmbH
Address: Gutenbergstraße 2, 48282 Emsdetten, DE
Product name: celexon Electric Expert and Expert XL
Products that are marked with the UKCA mark meet all requirements of the re-
levant UK directives. The UK declaration of conformity can be downloaded from
the following address: www.celexon.de/zertikate
INFORMATION ON UK CONFORMITY
The symbol indicates the separate collection of electrical and electronic
devices in EU countries. Please do not throw the device into household
waste. Find out about the return system applicable in your country and
contact your local authority or your local waste and pollutant collection
point if you have any questions about the disposal process.