Chamberlain STAR1000 User manual

LiftMastefr
APPTICATIOI{
The STAR1000 is a high capacity single channel commercial access
control receiver lor commercial door operators, and dry contact triggered
devices. The STAR1000 is compatible with Security* 2.OTM remote
controls and wireless keyless entries, Security* 2.0TM Passport and
Passport Lite remote controls. This receiver is compatible with
HomeLink@. For programming or compatibility information visit
www.homelink.com. The receiver capacity is 1,000 devices and can be
any combination of remote controls and wireless keyless entries. The
receiver is watertight according to lPX44 specification.
I{STAU.AT|0l{
1. Select a convenient location near the operator to be controlled by the
receiver within "line of sight" of the intended transmitting location.
NOTE: Do not mount LCD screen in direct sunlight. Avoid nounting
the receiver in a metal enclosure or near other wireless receiving or
transmitting devices.
2. Mount the bracket to the desired surface with appropriate hardware
(not provided) (Figure l ).
3. Remove the 4 (#8) screws on the back of the receiver and remove the
faceplate. Unplug the keypad connector from the control board.
N0lE: Be careful not to damage the keypad cable while removing the
faceplate.
4. Make wiring connections (Figure 2). Reter to your gate or commercial
door operator owner's manual for more specific information.
5. Beconnect the keypad connector to the board (labeled J9).
6. Secure the faceplate with the 4 (#8) screws previously removed.
7. lnstall the antenna provided.
NOIE: Use the optional 86LM or 86LMT antenna extension kit
(see page 4) to mount the remote antenna as high and far from
metallic objects as possible lor best radio range.
8. Snap the receiver onto the mounting bracket and secure with the
(#8) screws provided.
9. Tighten the watertight connector t0 secure and seal the wiring.
GOMMERGIAT AGCESS COilTROt REGEIUER
MODEL STAR|OOO
AAWARNING
To prevent possible SERI0US INJURY or DEATH trom electrocution:
. Be sure power is NOT connected BEF0RE installing the receiver.
To prevent possible SERI0US INJURY or DEATH from a moving gate
or garage door:
. ALWAYS keep remote controls out of reach of children. NEVER
permit children t0 operate, or play with remote control transmitters
. Activate gate or door 0NLY when it can be seen clearly, is properly
adiusted, and there are no obstructions to door travel.
. ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path ol moving gate or door.
A WARNING
To prevent possible SERI0US INJURY or DEATH, the use of
C0NSTANT 0PERATI0N on residential openers is PROHIBITED.
When a receiver is used to activate a commercial door opener, a
reversing edge MUST be installed on the bottom ofthe door. Failure to
install a reversing edge under these circumstances may result in
SERI0US INJURY or DEATH to persons trapped beneath the door.
Figure 1
N
Connection
Power
Conn€ction
I - 30 volts AC/DC
250 mA max
Power Supply
Single Operator

USER IIIIERFACE
The STAR1000 user interface consists ot a22 characler by 5 line LCD
display, 3 "soft keys", Down/Up arrows and a numeric keypad.
Scroll lndicalor
lf more than 3 options exist, a scroll
indicator appears on the left margin of
lines 2, 3, and 4. The scroll indicator
shows the relative position within the list.
Line 1:
Menu and function mode.
Lines 2, 3, and 4:
Menu selections and data.
Line 5:
Soft key function modes.
Antenna Conneclion
For the direct antenna or
the antenna extension kit.
Menu/Data selection
shown in inverse font
LCD Screen
System
programming and
status display.
"S0FT" Keys
Soft key functions
are defined by the
label on line 5 of the
display. The
functions change
according to the
menu selection.
DownflJp Keys
For navigation in
the menus.
llumeric Keypad
Numeric data is
entered through the
numeric keypad.
lnsert wiring
PROGRAMMIIIG
The receiver has the ability to learn a combination ol remote control
transmitters and keyless entries up to 1,000 devices. See page 4 for a
complete list of compatible accessories. Audible and visual warnings
occur when the receiver capacity is exceeded. After 30 seconds of
inactivity, the receiver times out and the LiftMasteP logo is displayed.
Select "UNL0CK" and enter the plN to continue.
lnilial Plil set up:
The PIN restricts access to authorized administrators only. ll you omit
this step, anyone will be able to program the receiver. Up-on initial power
up, the system firmware revision is displayed for 5 seconds followed
by the LiftMasteP logo. When a key is pressed, "CREATE plN?"
is displayed.
.l . Press "YES" to create PlN. lf the PIN is lost you may request a reset
code by pressing "RESET".
2. Enter a 6-digit PlN, and press "YES"; enter the 6-digit plN a second
time and press "YES" t0 program the plN. lf you make a mistake,
press "CLEAR" to change your entry. To exit the enter plN screen,
select "BACK".
3. When yolr 6-digit PIN is programmed correcfly, the LCD display
reads "KEYPAD UNLOCKED". Select ',0K,'to continue to the Main
Menu. After 30 seconds of inactivity, the receiver times out and
the LiftMasteP logo is displayed. Select ,,UNL0CK,' and enter plN
to continue.
M@
ME
@E
r@
L
Iil NEHU / FUHCTION
NEHU OFTIOH []RTR 2
NEHU BPTI(]N I)RTB 3

PROGRAMMING COMMATIDS
The table below describes the commands used to program the receiver
LEABN MENU LEABN DEVICE Program a device to the receiver.
BLOCK LEARN OEVICE Block program a range ol devices to the receiver
LEARN TO LOC #Program a device to a 4-digit number location
DELETE MENU DELETE DEVICE Delete a specified device that has been programmed to the receiver.
DELETE ALL OEVICES Delete all programmed devices.
SUSPEND MENU SUSPEND DEVICE Temporarily disables the function of a specified device that has been
programmed to the receiver.
SUSPEND ALL DEVICES Temporarily disables the function of ALL devices programmed to the
receiver.
UNSUSPEND DEVICE Re-enable the lunction ol a suspended device.
UNSUSPEND ALL DEVICES Re-enable the lunction ol ALL suspended devices
AUERY MENU LOC # USED Displays a range of used locations starting from a specified location.
LOC # AVAILABLE Displays a range of empty locations starting from a specified location.
LOC # SUSPENDED Displays a range of suspended locations starting from a specified
location.
sEr7rrtlcs CHANGE PIN Change the 6-digit PIN number for the receiver.
DEALER INFO Display and edit the dealer 11-digit contact phone number.
FIRMWARE VERSION Displays the current firmware version.
BEEP Turn the audible feedback on or off.
MEMORY DUPLICATE MEMOBY Creates a memory backup. A backup memory module must be
installed.
RESTORE MEMORY Restores a memory backup from a memory module.
N0fE: Content of memory backup module will over-write any
information already stored in the receiver memory.
RELAY Sets the relay activation time from .25 to 1 second.
CONTRAST Press Down or Up arrows to adjust LCD contrast
LANGUAGE Sets menu language: English (Default), Spanish, and French.
FACTORY DEFAULT Reset receiver to factory default settings
DtACNaSTtCS
The receiver emits a series of audible beeps to signal programming and
error events. The table at right lists all of the events and their audible
notifications. The 0n/0ff column indicates that the audible notification for
the event may be disabled in the BEEP SETTINGS menu.
Key press Single YES
Successlul Add Dou ble
Successlul Delete Triple
Successlul Suspend Double
Successlul Unsuspend Double
Master PIN entry error Long
Programming error Long
Location out ol range Long
Generic Success Dou ble
Generic Error Long
Received unknown Tx Slow YES
Received known Tx Double YES
Received known suspended Tx Lono YES
MAIN MENU COMMAND DESCRIPTION
EVENT AUDIBLE ON/OFF
NOTIFICATIONS
J

SPECIFICATIONS
System Capacity 1000 devices
Supply Voltage . . 9 - 30 Votts AC, 9 - 42 Votts DC
0perating Current. 50 mA Maximum
Stand By Current. 30 mA Maximum
SurgeSuppression.... .. 6.0kVMin
operating Temp Range -40'c to +65'C @ 50% Rh, -40'F to +149'F @ 50% Rh
Storage and Shipping Temp Range. -40'C to +85'C @ 50% Rh
Frequency Security+ 2.0TM Only (310, 315, 390, 433.30,433.92,
434 54, 868.30, 868.95, 869.85 MHz)
Relay Contact Bating. . 1 amp @ 24V AC/DC
COMPATIBLE ACCESSORIES
Remote Controls 81 1 LM, 81 3LM, 8g2LT, 8941T, 891 LM, 8931M,
890/893/895MAX, PPV1, PPV3, PPK1, PPK3, PPK1PH,
PPK3PH, PPLV1, PPLK1, AND PPLK1 PH
Keypads 8771M, and B77MAX
Antenna Extension Kits:
'15 ExtensionKits.... 86LM
25 ExtensionKits.... 86LMT
24VAC Transformer for screw terminals. 95LM
REPAIR PARTS
Antenna.
Memory Module . .
Mounting Bracket .
K76-36681
K1 D7530-4
K1 3-36651 -1
N0TICE: To comply with FCC and or lndustry Canada rules (lC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery, THERE ARE NO O]HER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards for Home or otfice use. operation is subiect to the loll0wing
two conditions: (1 ) this device may n0t cause harmlul interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FON TECHNICAL SUPPONT DAL OUR TOLL FBEE NUMBER:
1-800-528-2806