Chauvet Intimidator wave irc User manual

User Manual

Page 2 of 32 Intimidator™ Wave IRC User Manual Rev. 1
TABLE OF CONTENTS
1. Before You Begin.......................................................................................................... 4
What Is Included...............................................................................................................................4
Unpacking Instructions.....................................................................................................................4
Claims ....................................................................................................................................................... 4
Text Conventions .............................................................................................................................4
Symbols............................................................................................................................................4
Disclaimer.........................................................................................................................................4
Product at a Glance..........................................................................................................................5
Safety Notes.....................................................................................................................................5
2. Introduction................................................................................................................... 6
Overview...........................................................................................................................................6
Dimensions.......................................................................................................................................7
3. Setup.............................................................................................................................. 8
AC Power .........................................................................................................................................8
Fuse Replacement ................................................................................................................................... 8
Power Linking............................................................................................................................................ 9
Mounting.........................................................................................................................................10
Orientation............................................................................................................................................... 10
Rigging.................................................................................................................................................... 10
4. Operation......................................................................................................................11
Control Panel Operation.................................................................................................................11
Menu Map.......................................................................................................................................11
Configuration (DMX).......................................................................................................................11
Starting Address...................................................................................................................................... 11
DMX Personalities................................................................................................................................... 12
Master Auto............................................................................................................................................. 12
4-Head Program...................................................................................................................................... 12
Master Auto............................................................................................................................................. 13
2-Head Program...................................................................................................................................... 13
Master Auto............................................................................................................................................. 13
1-Head Program...................................................................................................................................... 13
DMX Assignments............................................................................................................14
34CH ..............................................................................................................................................14
DMX Assignments (Cont.) ...............................................................................................15
34CH ..............................................................................................................................................15
DMX Assignments (Cont.) ...............................................................................................16
34CH ..............................................................................................................................................16
DMX Assignments (Cont.) ...............................................................................................17
34CH ..............................................................................................................................................17
DMX Assignments (Cont.) ...............................................................................................18
34CH ..............................................................................................................................................18
DMX Assignments (Cont.) ...............................................................................................19
34CH ..............................................................................................................................................19
DMX Assignments (Cont.) ...............................................................................................20
34CH ..............................................................................................................................................20
DMX Assignments (Cont.) ...............................................................................................21
14CH ..............................................................................................................................................21
DMX Assignments (Cont.) ...............................................................................................22

Intimidator™ Wave IRC User Manual Rev. 1 Page 3 of 32
14CH ..............................................................................................................................................22
DMX Assignments (Cont.) ...............................................................................................23
14CH ..............................................................................................................................................23
DMX Assignments (Cont.) ...............................................................................................24
14CH ..............................................................................................................................................24
DMX Assignments (Cont.) ...............................................................................................25
14CH ..............................................................................................................................................25
DMX Assignments (Cont.) ...............................................................................................26
14CH ..............................................................................................................................................26
Configuration (Standalone) ............................................................................................................27
Sound-Active Mode................................................................................................................................. 27
Automatic Mode....................................................................................................................................... 27
Manual Reverse Tilt Operation................................................................................................................ 27
Manual Tilt Angle Range......................................................................................................................... 27
Display Blackout and Reverse................................................................................................................. 28
Master/Slave Mode.................................................................................................................................. 28
Reset Software...............................................................................................................................28
Factory Defaults .............................................................................................................................28
5. Technical Information..................................................................................................29
Product Maintenance .....................................................................................................................29
6. Technical Specifications..............................................................................................30
Returns .............................................................................................................................31
Contact Us........................................................................................................................32

Page 4 of 32 Intimidator™ Wave IRC User Manual Rev. 1
1.BEFORE YOU BEGIN
What Is
Included
•Intimidator™ Wave IRC
•Hanging bracket with mounting
hardware
•Power cord
•Warranty card
•Quick Reference Guide
Unpacking
Instructions
Carefully unpack the product immediately and che
ck the container to make sure all the
parts are in the package and are in good condition.
Claims
If the box or the contents (the product and
included accessories) appear damaged from
shipping, or show signs of mishandling, notify the carrier immediately, not Chauvet
Failure to report damage to the carrier immediately may invalidate your claim. In
addition, keep the box and contents for inspection.
For other issues, such as
missing components or parts, damage not related to shipping,
or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text
Conventions
Convention Meaning
1–512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified
Menu > Settings
A sequence of menu options to be followed
<ENTER>
A key to be pressed on the product’s control panel
ON
A value to be entered or selected
Symbols
Symbol Meaning
Critical installation, configuration, or operation information. Not
following these instructions may make the product not work, cause
damage to the product, or cause harm to the operator.
Important installation or configuration information. The product
may not function correctly if this information is not used.
Useful information.
Disclaimer
The information and specifications contained in this User Manual
are subject to change
without notice. Chauvet assumes no responsibility or liabil
ity for any errors or omissions,
and reserves the right to revise or recreate this manual at any time. Downloa
d the latest
version from www.chauvetlighting.com.
© Copyright 2014 Chauvet All rights reserved.
Electronically published by Chauvet in the United States of America.
Author Date Editor Date
M. Trouard 10/17/2014 A. Leon 11/3/14

Intimidator™ Wave IRC User Manual Rev. 1 Page 5 of 32
Product at a
Glance
Use on Dimmer
x
Auto Programs
P
Outdoor Use
x
Auto-ranging Power Supply
P
Sound-Activated
P
Replaceable Fuse
P
DMX
P
User-Serviceable
x
Master/Slave
P
Safety Notes
These notes include important i
nformation about the mounting, usage, and maintenance
of this product; read before using the product.
•Always connect the product to a grounded circuit to avoid the risk of electrocution.
•Always disconnect the product from the power source before cleaning or replacing
the fuse.
•Avoid direct eye exposure to the light source while the product is on.
•Make sure the power cord is not crimped or damaged.
•Never disconnect the product from power by pulling or tugging on the cord.
•If mounting the product overhead, always secure to a fastening device using a
safety cable.
•Make sure there are no flammable materials close to the product when operating.
•
Do not touch the product’s housing when operating because it may be very hot.
•Always make sure that the voltage of the outlet to which you are connecting the
product is within the range stated on the decal or rear panel of the product.
•The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not
expose the product to rain or moisture.
•Always install the product in a location with adequate ventilation, at least 20 in
(50 cm) from adjacent surfaces.
•Be sure that no ventilation slots on the product’s housing are blocked.
•Never connect the product to a dimmer.
•Make sure to replace the fuse with another of the same type and rating.
•Never carry the product from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.
•The maximum ambient temperature (Ta) is 104 °F (40 °C). Do not operate the
product at higher temperatures.
•In the event of a serious operating problem, stop using the product immediately.
•Never try to repair the product. Repairs carried out by unskilled people can lead to
damage or malfunction. Contact the nearest authorized technical assistance center.
•This product is not intended for permanent installation.
•To eliminate unnecessary wear and improve its lifespan, during periods of non-use
completely disconnect the product from the power via breaker or by unplugging it.
Keep this User Manual for future use. If you sell the product to another user, be sure to
give this document to the next owner.

Page 6 of 32 Intimidator™ Wave IRC User Manual Rev. 1
2.INTRODUCTION
Overview
Front Panel View
Display
Control
Buttons
Back Panel View
Power In
Fuse Holder
Power Out
DMX Out
DMX In
Head
1
Head
2
Head
3
Head
4
Head
5

Intimidator™ Wave IRC User Manual Rev. 1 Page 7 of 32
Dimensions
28 in
712 mm
4.4 in
113 mm
9.6 in
243 mm

Page 8 of 32 Intimidator™ Wave IRC User Manual Rev. 1
3.SETUP
AC Power
The Intimidator™ Wave IRC has an auto-
ranging power supply and it can work with an
input voltage range of 100–240 VAC, 50/60 Hz.
To determine the product’s power requirements (
circuit breaker, power outlet, and
wiring), use the current value listed on the label affixed to the product
’s back panel, or
refer to the product
’s specifications chart. The listed current rating indicates the
product’s average current draw under normal conditions.
Always connect the product to a protected circuit
(circuit breaker or fuse). Make
sure the product
has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect the product
to a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Disconnect the product from power before replacing the fuse.
Fuse
Replacement
1. Disconnect the product from power.
2. Use a Phillips #2 head screwdriver to unscrew the fuse
holder cap from the housing.
3. Remove the blown fuse.
4. Replace with a fuse of the same type and rating.
5. Screw the fuse holder cap back in place and reconnect
power.
Always replace a blown fuse with another of the same type and rating.

Intimidator™ Wave IRC User Manual Rev. 1 Page 9 of 32
Power Linking
The product provides power linkin
g via the Edison/IEC outlet located in the front/back of
the unit.
Power Linking
Diagram
You can power link up to 5 Intimidator™ Wave IRC unit
s on 120 VAC or up to
13 Intimidator™ Wave IRC units on 230 VAC.
The power linking diagram shown above corresponds to the North American
version of the product ONLY! If using the product
in other markets, you must
consult with the local Chauvet
distributor as power linking connectors and
requirements may differ in your country or region.
1st Product
2nd Product
3rd Product
Additional Products

Page 10 of 32 Intimidator™ Wave IRC User Manual Rev. 1
Mounting
Before mounting the product
, read and follow the safety recommendations indicated in
the Safety Notes. For our CHAUVET® line of mounting
clamps, go to
www.chauvetlighting.com/cables-clamps-main.html/.
Orientation
The Intimidator™ Wave IRC
may be mounted in any position; however, make sure
adequate ventilation is provided around the product.
Rigging
•Before deciding on a location, always make sure there is easy access to the product
for maintenance and programming.
•Make sure that the structure or surface onto which you are mounting the product
can support the product’s weight (see the Technical Specifications).
•When mounting the product overhead, always use a safety cable (such as CH-05
from Chauvet). Mount the product securely to a rigging point, such as
an elevated
platform or a truss.
•When rigging the product onto a truss, you should use mounting clamps
(such as
CLP-15 from Chauvet) of appropriate weight capacity. The bracket has 13-mm
holes, which are appropriate for this purpose.
•When power linking multiple products, you must
always consider the length of the
power linking cable and mount the products close enough for the cable to reach.
•The mounting bracket also allows for surface mounting. When mounting the product
on the floor, make sure that the product and cables are a
way from people and
vehicles.
Mounting Diagram
When using only one mounting clamp with this fixture, you must use a clamp with a
captive bolt to prevent accidental loosening.
Mounting
Clamps
Safety
Cable
Hanging/
Mounting
Bracket
Rubber Feet
(x4) for floor
mounting

Intimidator™ Wave IRC User Manual Rev. 1 Page 11 of 32
4.OPERATION
Control Panel
Operation
To access the control panel functions, use the four buttons located underneath the
display.
Button Function
<MENU> Selects an operation mode or backs out of the current menu option
<UP> Scrolls up the list of options or selects a higher value
<DOWN> Scrolls down the list of options or selects a lower value
<ENTER> Activates a menu option or a selected value
Menu Map
Mode Programming Levels Description
Address
001–512
Sets DMX starting address
Run Mode
DMX
14CH
Sets DMX personality
34CH
Auto
Auto01–
Auto16
Sets an auto program
Sound
Sets Sound mode
Slave
S-1–S-4
Sets a Slave mode
IR
Sets Infrared mode
Setup
Mast Set
M-1–M-4
Sets a Master mode of M-1, M-2 or M-4
Tilt Reverse
ON
Sets reverse tilt operation
OFF
Tilt Angle
90
Sets tilt angle range
180
270
Display
ON
Sets display blackout
OFF
Screen Reverse
ON
Sets screen orientation
OFF
Sensitivity
1–100
Sets sound sensitivity
Reset
Resets all motor defaults
Factory Reset
Resets to factory defaults
System Info
Ver XX
Displays software version
Running Mode XXXXX
Displays current operating mode
DMX Address XXX
Displays current DMX address
Configuration
(DMX)
Set the product in DMX mode to control with a DMX controller.
1. Connect the product to a suitable power outlet.
2. Connect a DMX cable from the DMX output of the DMX controller to the DMX input
on the product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX channels
the selected DMX mode uses. If you
choose a starting address that is too high, you could
restrict the access to some of the product’s channels.
The Intimidator™ Wave IRC uses up to 34 DMX channels in its 34-channel
personality,
which defines the highest configurable address to 479.
If unfamiliar with DMX, download the DMX Primer from www.chauvetlighting.com.
To select the starting address, do the following:
1. Press <MENU>
2. Use <UP> or <DOWN> to select the Address.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to enter your starting address.
5. Press <ENTER>.

Page 12 of 32 Intimidator™ Wave IRC User Manual Rev. 1
DMX
Personalities
The Intimidator™ Wave IRC has two DMX personalities, a 34-
channel personality and a
14-channel personality.
To choose which DMX personality to use, follow the steps below:
1. Press <MENU>.
2. Use <UP> or <DOWN> to select Run Mode.
3. Press <ENTER>.
4. Use <UP> or <DOWN> to select DMX.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select your DMX personality and press <ENTER>.
Master Auto
Programs
The Master Auto built-in programs control the actions of two or more
Intimidator™ Wave IRC
units linked together by DMX data connection. A single Intimidator™ Wave IRC
(the master)
controls the actions of another Intimidator™ Wave IRC
(the slave). Configure the Master Auto
programs in conjunction with the Slave modes as follows:
Master Auto
4-
Head
Program
The Master Auto 4-Head program allows all 5 heads of four linked Intimidator™ Wave IRC
units
to operate in unison. The master unit will be set to operate in the
M-4 program, while the slave unit will be set to operate in either Slave S-1, Slave S-2
,
Slave S-3, or Slave S-4 mode.
Configure the units as indicated below.
Master unit:
1. Press <MENU> and use <UP> or <DOWN> to select Setup.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select Mast Set and press <ENTER>.
4. Use <UP> or <DOWN> to scroll to M-1, M-2, or M-4.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select M-4.
7. Press <ENTER>.
Slave unit:
1. Press <MENU> and use <UP> or <DOWN> to select Run Mode.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select Slave S-1, Slave S-2, Slave S-3, or Slave S-4.
4. Press <ENTER>.
5. Select Slave S-1 for 100% synchronized actions.
6. Select Slave S-2, S-3 or S-4 for a delayed show with all 5 heads, up to 20 heads total,
in the
same direction but with a delay creating a wave effect.
7. Press <ENTER>.

Intimidator™ Wave IRC User Manual Rev. 1 Page 13 of 32
Master Auto
2-
Head
Program
The Master Auto 2-Head program allows a single Intimidator™ Wave IRC
to control the actions
of another Intimidator™ Wave IRC. The master unit will be set to operate in the M-
2 program,
while the slave unit will be set to operate in either Slave S-1 or Slave S-2 mode.
Configure the units as indicated below.
Master unit:
1. Press <MENU> and use <UP> or <DOWN> to select Setup.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select Mast Set and press <ENTER>.
4. Use <UP> or <DOWN> to scroll to M-1, M-2, or M-4.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select M-2.
7. Press <ENTER>.
Slave unit:
1. Press <MENU> and use <UP> or <DOWN> to select Run Mode.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select Slave S-1, or Slave S-2.
•Select Slave S-1 for 100% synchronized actions with both units,
up to 10 heads in
tandem.
•Select Slave S-2 for a delayed wave, up to 10 heads.
4. Press <ENTER>.
Master Auto
1-
Head
Program
The Master Auto 1-Head program allows all 4 heads of two linked Intimidator™ Wave IRC
units
to operate in unison. The master unit will be set to operate in the
M-1 program, while the slave unit will be set to operate in Slave S-1, Slave S-2, Slave S-
3, or
Slave S-4 mode.
Configure the units as indicated below.
Master unit:
1. Press <MENU> and use <UP> or <DOWN> to select Setup.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select Mast Set and press <ENTER>.
4. Use <UP> or <DOWN> to scroll to M-1, M-2, or M-4.
5. Press <ENTER>.
6. Use <UP> or <DOWN> to select M-1.
7. Press <ENTER>.
Slave unit:
1. Press <MENU> and use <UP> or <DOWN> to select Run Mode.
2. Press <ENTER>.
3. Use <UP> or <DOWN> to select Slave S-1, Slave S-2, Slave S-3, or Slave S-4.
4. Press <ENTER>.
5. Select Slave S-1 for 100% synchronized control of up to another 20 heads.
6. Press <ENTER>.

Page 14 of 32 Intimidator™ Wave IRC User Manual Rev. 1
DMXASSIGNMENTS
34CH
Channel
Function
Value
Percent/Setting
1
Head 1 Tilt
000ó255
0–270°
2
Head 2 Tilt
000ó255
0–270°
3
Head 3 Tilt
000ó255
0–270°
4
Head 4 Tilt
000ó255
0–270°
5
Head 5 Tilt
000ó255
0–270°
6 Head Tilt Programs
000ó047
No function
048ó055
Program 1
056ó063
Program 2
064ó071
Program 3
072ó079
Program 4
080ó087
Program 5
088ó095
Program 6
096ó103
Program 7
104ó111
Program 8
112ó119
Program 9
120ó127
Program 10
128ó135
Program 11
136ó143
Program 12
144ó151
Program 13
152ó159
Program 14
160ó167
Program 15
168ó175
Program 16
176ó183
Program 17
184ó191
Program 18
192ó199
Program 19
200ó207
Program 20
208ó215
Program 21
216ó223
Program 22
224ó231
Program 23
232ó239
Program 24
240ó247
Program 1 all heads
248ó255
Sound program
7
Head Tilt Program
Speed
000ó255 Fast to slow
8
Head 1 Red
Dimmer
000ó255 0–100%
9
Head 1 Green
Dimmer
000ó255 0–100%

Intimidator™ Wave IRC User Manual Rev. 1 Page 15 of 32
DMXASSIGNMENTS (CONT.)
34CH
Channel
Function
Value
Percent/Setting
10
Head 1 Blue
Dimmer
000ó255 0–100%
11
Head 1 White
Dimmer
000ó255 0–100%
12
Head 2 Red
Dimmer
000ó255 0–100%
13
Head 2 Green
Dimmer
000ó055 0–100%
14
Head 2 Blue
Dimmer
000ó255 0–100%
15
Head 2 White
Dimmer
000ó255 0–100%
16
Head 3 Red
Dimmer
000ó255 0–100%
17
Head 3 Green
Dimmer
000ó255 0–100%
18
Head 3 Blue
Dimmer
000ó255 0–100%
19
Head 3 White
Dimmer
000ó255 0–100%
20
Head 4 Red
Dimmer
000ó255 0–100%
21
Head 4 Green
Dimmer
000ó255 0–100%
22
Head 4 Blue
Dimmer
000ó255 0–100%
23
Head 4 White
Dimmer
000ó255 0–100%
24
Head 5 Red
Dimmer
000ó255 0–100%
25
Head 5 Green
Dimmer
000ó255 0–100%
26
Head 5 Blue
Dimmer
000ó255 0–100%
27
Head 5 White
Dimmer
000ó255 0–100%

Page 16 of 32 Intimidator™ Wave IRC User Manual Rev. 1
DMXASSIGNMENTS (CONT.)
34CH
Channel
Function
Value
Percent/Setting
28 Colors
000ó007
No function
008ó015
Color 1
016ó023
Color 2
024ó031
Color 3
032ó039
Color 4
040ó047
Color 5
048ó055
Color 6
056ó063
Color 7
064ó071
Color 8
072ó079
Color 9
080ó087
Color 10
088ó095
Color 11
096ó103
Color 12
104ó111
Color 13
112ó119
Color 14
120ó127
Color 15
128ó179
Reserved
180ó201
Fade rainbow clockwise (speed fast to slow)
202ó207
Full on of current color
208ó229
Fade rainbow counter-clockwise
(speed fast to slow)
230ó234
All colors 100%
235ó249
Snap change (speed fast to slow)
250ó255
Sound color

Intimidator™ Wave IRC User Manual Rev. 1 Page 17 of 32
DMXASSIGNMENTS (CONT.)
34CH
Channel
Function
Value
Percent/Setting
29 Heads On/Off
000ó007
●●●●●
008ó015
●●●●○
016ó023
●●●○○
024ó031
●●○○○
032ó039
●○○○○
040ó047
○○○○○
048ó055
○○○○●
056ó063
○○○●●
064ó071
○○●●●
072ó079
○●●●●
080ó087
●●●●●
088ó095
○○○○●
096ó103
○○○●○
104ó111
○○●○○
112ó119
○●○○○
120ó127
●○○○○
128ó135
○○○●●
136ó143
○○●●○
144ó151
○●●○○
152ó159
●●○○○
160ó167
●○○○●
168ó175
○○●●●
176ó183
○●●●○
184ó191
○○●●●
192ó199
●●○○●
200ó207
●○○●●
208ó215
○●●●●
216ó223
●●●●○
224ó231
●●●○●
232ó239
●●○●●
240ó247
●○●●●
248ó255
●●●●●

Page 18 of 32 Intimidator™ Wave IRC User Manual Rev. 1
DMXASSIGNMENTS (CONT.)
34CH
Channel
Function
Value
Percent/Setting
30 Auto Programs
000ó015
No function
016ó020
Program 1
021ó025
Program 2
026ó030
Program 3
031ó035
Program 4
036ó040
Program 5
041ó045
Program 6
046ó050
Program 7
051ó055
Program 8
056ó060
Program 9
061ó065
Program 10
066ó070
Program 11
071ó075
Program 12
076ó080
Program 13
081ó085
Program 14
086ó090
Program 15
091ó095
Program 16
096ó100
Program 17
101ó105
Program 18
106ó110
Program 19
111ó115
Program 20
116ó120
Program 21
121ó125
Program 22
126ó130
Program 23
131ó135
Program 24 (built-in for all)
136ó140
Program 25
141ó145
Program 26
146ó150
Program 27
151ó155
Program 28
156ó160
Program 29
161ó165
Program 30
166ó170
Program 31
171ó175
Program 32
176ó180
Program 33
181ó185
Program 34
186ó190
Program 35
191ó195
Program 36

Intimidator™ Wave IRC User Manual Rev. 1 Page 19 of 32
DMXASSIGNMENTS (CONT.)
34CH
Channel
Function
Value
Percent/Setting
30 Auto Programs
(Cont.)
196ó200
Program 37
201ó205
Program 38
206ó210
Program 39
211ó215
Program 40
216ó220
Program 41
221ó225
Program 42
226ó230
Program 43
231ó235
Program 44
236ó240
Program 45
241ó245
Program 46
246ó250
Program 47
251ó255
Program 48 (built-in for all)
31
Program Speed
000ó255
Slow to fast
32
Dimmer All Heads
000ó255
0–100%
33 Shutter Programs
000ó019
Off
020ó024
On
025ó064
Shutter 1 even on/even off (fast to slow)
065ó069
On
070ó084
Shutter 2 fast on/slow off (fast to slow)
085ó089
On
090ó104
Shutter 3 slow on/fast off (fast to slow)
105ó109
On
110ó124
Shutter 4 random shutter (fast to slow)
125ó129
On
130ó144
Shutter 5 random shutter fast on/slow off
(fast to slow)
145ó149
On
150ó164
Shutter 6 random shutter slow on/fast off
(fast to slow)
165ó169
On
170ó184
Shutter 7 pulse shutter (fast to slow)
185ó189
On
190ó204
Shutter 8 random pulse shutter (fast to slow)
205ó209
On
210ó224
Shutter 9 on and off gradually (fast to slow)
225ó229
On
230ó244
Shutter 10 pulse shutter (fast to slow)
245ó255
On

Page 20 of 32 Intimidator™ Wave IRC User Manual Rev. 1
DMXASSIGNMENTS (CONT.)
34CH
Channel
Function
Value
Percent/Setting
34
Settings
(Set these values
before setting
other DMX
channels. There is
a 10 sec delay
before the settings
take effect)
000ó009
No function
010ó014
Move-in-black
015ó019
Cancel move-in-black
020ó024
Independent macros – cancels macro product
combinations below
025ó029
Macros used when linking 2 products together: This is
the value for first product
030ó034
Macros used when linking 2 products together:
This is the value for second product
035ó039
Macros used when linking 4 products together:
This is the value for first product
040ó044
Macros used when linking 4 products together:
This is the value for second product
045ó049
Macros used when linking 4 products together:
This is the value for third product
050ó054
Macros used when linking 4 products together:
This is the value for fourth product
055ó059
No function
060ó064
Reset tilt only
065ó069
No function
070ó074
Reset all
075ó089
No function
090ó094
Reverse tilt
095ó099
No function
100ó104
Cancel reverse tilt
105ó114
No function
115ó119
Controls all heads with head 1 channels
120ó124
Cancels control of all heads with
head 1 channels
125ó255
No function