Chauvet LEDsplash 86B User manual

5200 NW 108th Avenue, Sunrise, FL 33351 U.S.A.
[phone] – [phone]
FAX [phone]
www.chauvetlighting.com
User Manual
Snapshot
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
Auto-ranging
Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle

TABLE OF CONTENTS
1. BEFORE YOU BEGIN....................................................................................................................................................... 3
WHAT IS INCLUDED................................................................................................................................................................................3
UNPACKING INSTRUCTIONS....................................................................................................................................................................3
MANUAL CONVENTIONS.........................................................................................................................................................................3
ICONS ..................................................................................................................................................................................................3
SAFETY INSTRUCTIONS..........................................................................................................................................................................4
2. INTRODUCTION ............................................................................................................................................................... 5
FEATURES............................................................................................................................................................................................5
PRODUCT OVERVIEW ............................................................................................................................................................................5
3. SETUP............................................................................................................................................................................... 5
ACPOWER...........................................................................................................................................................................................6
Power Linking ............................................................................................................................................................... 6
MOUNTING ...........................................................................................................................................................................................6
Orientation .................................................................................................................................................................... 6
Rigging.......................................................................................................................................................................... 6
4. OPERATING INSTRUCTIONS.......................................................................................................................................... 8
CONFIGURING THE STARTING ADDRESS..................................................................................................................................................8
DMXOPERATION .................................................................................................................................................................................8
ACCESSING THE 2PERSONALITIES..........................................................................................................................................................8
MASTER/SLAVE MODE (SOUND-ACTIVE,AUTO MODE,STATIC COLORS)...................................................................................................8
STROBE SPEED.....................................................................................................................................................................................8
STANDALONE OPERATION......................................................................................................................................................................8
Automatic...................................................................................................................................................................... 8
Sound-Active................................................................................................................................................................. 9
Static Colors.................................................................................................................................................................. 9
DMXCHANNEL VALUES........................................................................................................................................................................9
5. APPENDIX....................................................................................................................................................................... 10
GENERAL MAINTENANCE .....................................................................................................................................................................10
DATA CABLING....................................................................................................................................................................................10
FIXTURE LINKING ................................................................................................................................................................................10
GENERAL TROUBLESHOOTING..............................................................................................................................................................11
RETURN PROCEDURE..........................................................................................................................................................................11
CLAIMS ..............................................................................................................................................................................................11
TECHNICAL SPECIFICATIONS ................................................................................................................................................................12
CONTACT US......................................................................................................................................................................................12

LEDSplash 86B User Manual 3 Rev. 3
1.BEFORE YOU BEGIN
What is Included
1 x LEDsplash™ 86B
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
Manual Conventions
CHAUVET® manuals use the following conventions to differentiate certain types of information from
the regular text.
CONVENTION MEANING
[10] A DIP switch to be configured
<Menu> A key to be pressed on the fixture’s control panel
1~512 A range of values
50/60 A set of values of which only one can be chosen
Settings A menu option not to be modified (for example, showing the operating
mode/current status)
MENU > Settings A sequence of menu options to be followed
ON
A value to be entered or selected
Icons This manual uses the following icons to indicate information that requires special attention on the part
of the user.
ICONS MEANING
C
ritical installation, configuration or operation information. Failure to
comply with this information may render the fixture partially or completely
inoperative, cause damage to the fixture or cause harm to the user.
Important installation or configuration information. Failure to comply with
this information may prevent the fixture from functioning correctly.
Useful non-critical information.

LEDSplash 86B User Manual 4 Rev. 3
Safety Instructions
•Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that
they also receive this instruction booklet.
•Always make sure that you are connecting to the proper voltage, and that the line voltage you are
connecting to is not higher than that stated on the decal or rear panel of the fixture.
•This product is intended for indoor use only! To prevent risk of fire or shock, do not expose fixture to
rain or moisture.
•Make sure there are no flammable materials close to the unit while operating.
•The unit must be installed in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces. Be sure that no ventilation slots are blocked.
•Always disconnect from power source before servicing or replacing fuse and be sure to replace with
same fuse source.
•Secure fixture to fastening device using a safety chain.
•Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate fixture at temperatures higher
than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the
unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please
contact the nearest authorized technical assistance center.
•Never connect the device to a dimmer pack.
•Make sure the power cord is never crimped or damaged.
•Never disconnect the power cord by pulling or tugging on the cord.
•Never carry the fixture directly from the cord. Always use the hanging/mounting bracket.
•Avoid direct eye exposure to the light source while it is on.
Read these instructions carefully. They contain important information
about the installation, usage, and maintenance of this product.

LEDSplash 86B User Manual 5 Rev. 3
2.INTRODUCTION
Features
•3 or 7-channel DMX-512 LED PAR can
•Operating modes:
3-channel: RGB control
7-channel: RGB, macros, run/strobe speed, automatic/sound, dimmer
•Static colors and RGB color mixing with or without DMX controller
•Built-in automated programs via master/slave or DMX with variable speed
•Built-in sound activated programs via master/slave or DMX
•Pulse effect with adjustable speed
Additional Features
•Additional power output: max 37 units
•Double-bracket yoke doubles as floor stand
Product Overview
Microphone Sensitivity
Adjustment Knob
Power In
Microphone
DMX In
DIP Switches
Power Out
DMX Out
Fuseholder

LEDSplash 86B User Manual 6 Rev. 3
3.SETUP
AC Power This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage
to which you are connecting it is within the range of accepted voltages.
Always connect the fixture to a switched circuit. Never connect the fixture to a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used only as a 0
to 100% switch.
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating indicates its
average current draw under normal conditions.
Always connect the fixture to a circuit with a suitable electrical ground.
Power Linking
This fixture contains power linking via the Edison outlet located in front of the power input cable.
Please see the diagram below for further explanation.
The maximum quantity of fixtures that may be linked is 37.
The power linking in this document is for the Chauvet® North American version ONLY!
Therefore, it is the customer’s responsibility to check with the Dealer/Distributor regarding
power linking on the local version of the product. Connections and availability may change,
depending on the power requirements and/or regulations of each country/region.
Mounting
Orientation
The LEDsplash™ 86B may be mounted in any safe position, provided there is adequate room
for ventilation.
Rigging
Be sure that the structure can support the weight of the fixture. Please see the “Technical
Specifications” section of this manual for a detailed weight listing. Mount the fixture securely.
This may be done with a screw, nut and bolt, or a hanging clamp. The hole in each bracket is 13
mm in size. When rigging consider routine maintenance and control panel access. Please see
the following steps for installation.

LEDSplash 86B User Manual 7 Rev. 3
Mounting
Bracket
Bracket
Adjustment Knob
•If the power link out is intended to be used with multiple fixture, take into account the length
of each power cable, and mount the fixtures close enough to one another to accommodate
for this.
•When aiming the fixtures, you may use the bracket adjustment knob. Loosen the knob,
adjust to the desired angle, and then tighten the knob by turning clockwise. Do not use
tools for this step, as it may cause damage.
•Safety cables must always be used.

LEDSplash 86B User Manual 8 Rev. 3
4.OPERATING INSTRUCTIONS
Configuring the Starting Address
Each fixture requires a starting address from 1~512. A fixture requiring one or more channels for
control begins to read the data on the channel indicated by the starting address. For example, a
fixture that uses seven DMX channels and is addressed to start on DMX channel 100, will read data
from channels: 100, 101, 102, 103, 104, 105 and 106. Choose the starting addresses for each fixture
so that the channels used do not overlap. In addition, you should note the starting address selected
for future reference. If you are unfamiliar with DMX, download the DMX Primer from
www.chauvetlighting.com. The LEDsplash™ 86B fixture uses seven or three DMX channels. If this is
your first time using DMX, we recommend reading the “DMX Primer” section in the “Appendix”.
DMX Operation
This is the operating mode which will allow for control with an external DMX controller. You must set
the starting address for this mode. If this is your first time using DMX, then it is recommended that
you refer to the “DMX Primer” section in the “Appendix” of this manual.
Mode DIP switches
DMX 1~9 = set to the DMX starting address
10 = Off
Accessing the 2 Personalities
There are two personalities for this fixture. There is the standard 7-channel personality with strobe
and color macros, and then there is the basic 3-channel RGB personality. Please see the DIP switch
settings to access each of these personalities below.
Mode DIP switches
7-CH 11-12 = Off
3-CH 11 = On
Master/Slave Mode (Sound-Active, Auto Mode, Static Colors)
This mode allows a single unit to run a standalone program, while 1 or more other units follow the
same operation. This requires the fixtures to be linked with DMX cables. Please see the section on
Fixture Linking.
1) The Master unit may be operated in Automatic, Sound-Active, and Static Colors.
2) Adjust the DIP switches to the Slave position on the slave units, and they will react the same as
the Master. See below for DIP switch assignment.
Mode DIP switches
Slave 2~11 = Off
1 = On
Strobe Speed
This fixture has a strobe speed adjustment which will decrease the maximum speed. Please see the
setting below for lowering the strobe rate for compatibility mode.
Mode DIP switches
Standard mode
6 Hz~18 Hz: 12 = On
Decreased Speed
2 Hz~6 Hz: 12 = Off
Standalone Operation
Automatic
This fixture has a preprogrammed color fade program. This is accessed via the DIP switches on the
back of the fixture, and the speed may be increased, as well. Please see the chart below for further
explanation. Mode DIP switches
Master Auto 7, 9, 10 = On
Increase Speed 1~6 = On (add more DIP switches to reach higher speed)

LEDSplash 86B User Manual 9 Rev. 3
Sound-Active
This fixture has preprogrammed sound triggered chases. These are accessed via the DIP switches
on the back of the fixture, and the sensitivity may be adjusted using the audio adjustment knob.
Please see the chart below for further explanation.
Mode DIP switches
Master Sound 10 = On
Static Colors
This unit has separate DIP switches for each of the 3 colors (red, green, and blue). These are
accessed via the DIP switches on the back of the fixture. Each of the 3 colors may be mixed with
different intensities. Please see the chart below for further explanation.
Mode DIP switches
Master Static 8, 9, 10 = On
Static (Red) 1~2 = On
Static (Green) 3~4 = On
Static (Blue) 5~6 = On
DMX Channel Values
7-CH Mode
CHANNEL
VALUE
FUNCTION
1
000

255
Red
Dimmer: 0%~100%
2
000

255
Green
Dimmer: 0%~100%
3
000 255 Blue Dimmer: 0%~100%
4 000 015
016 255
Color Macros (overrides CH.1~3)
No Function
Color Macros
5
000 255
Speed (CH.6 @ values 32~223)
Slow~Fast
000 015
016 255
Strobe (RGB & Macro only)
No Function
Slow~Fast
6
000 031
032 063
064 095
096 127
128 159
160 191
192 223
224 255
Mode
RGB mode
Pulse effect 0%~100% (using RGB faders)
Pulse effect 100%~0% (using RGB faders)
Pulse effect 100%~0%~100% (using RGB faders)
Auto fade transition
Auto snap transition (3 colors)
Auto snap transition (7 colors)
Sound triggering mode
When CH.6 is set @ 032~223,
CH.5 controls the speed.
7
000 255
Dimmer
Intensity (RGB/Macro modes): 0%~100%
3-CH Mode
CHANNEL
VALUE
FUNCTION
1
000 255
Red
Dimmer: 0%~100%
2
000

255
Green
Dimmer: 0%~100%
3
000 255
Blue
Dimmer: 0%~100%

LEDSplash 86B User Manual 10 Rev. 3
5.APPENDIX
General Maintenance
To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
•Unplug fixture from power.
•Use a vacuum or air compressor and a soft brush to remove dust collected on external
vents.
•Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl
Alcohol and a soft lint free cotton cloth or lens tissue.
•Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens.
•Gently polish optical surfaces until they are free of haze and lint.
The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light
output. Cleaning frequency depends on the environment in which the fixture operates. Damp, smoky
or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics. Clean
with soft cloth using normal glass cleaning fluid. Clean the external optics at least every 20 days.
Clean the fixture at least every 30/60 days.
Always dry the parts carefully after cleaning them.
Never spin a fan using compressed air.
Data Cabling
To link fixtures together you must obtain data cables. You can purchase CHAUVET® certified DMX
cables directly from a dealer/distributor or construct your own cable. If you choose to create your own
cable please use data-grade cables that can carry a high quality signal and are less prone to
electromagnetic interference. Use a Belden© 9841 or equivalent cable which meets the specifications
for EIA RS-485 applications. Standard microphone cables cannot transmit DMX data reliably over
long distances.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to
run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures
the data link can support.
Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-
485 standard, no more than 32 fixtures should be connected on one data link. Connecting
more than 32 fixtures on one serial data link without the use of a DMX optically-isolated
splitter may result in deterioration of the digital DMX signal.
Maximum recommended serial data link distance: 500 m (1640 ft)
Maximum recommended number of fixtures on a serial data link: 32

LEDSplash 86B User Manual 11 Rev. 3
General Troubleshooting
SYMPTOM POSSIBLE CAUSE(S) POSSIBLE ACTION(S)
Breaker/Fuse
keeps blowing
Excessive circuit load Check total load placed on the electrical circuit.
Short circuit along the power wires Check for a short in the electrical wiring (internal and/or
external)
Device does not
power up No power Check for power on power outlet
Loose power cord Check power cord
Fixture is not
responding to
DMX
Wrong DMX addressing Check Control Panel and unit addressing
Damaged DMX cables Check DMX cables
Wrong polarity settings on the
controller Check polarity switch settings on the controller
Loose DMX cables Check cable connections
Faulty DMX interface Replace DMX input
Faulty Main PCB Replace Main PCB
Loss of signal
Non DMX cables Use only DMX compatible cables
Bouncing signals Install terminator as suggested
Long cable / Low level signal Install amplifier right after fixture with strong signal
Too many fixtures Install an optically coupled DMX splitter after unit #32
Interference from AC wires Keep DMX cables separated from power cables or black
lights
If you still have a problem after trying the above solutions, please contact CHAUVET®
Technical Support.
Return Procedure
Returned merchandise must be sent prepaid and in the original packing; call tags will not be issued.
Package must be clearly labeled with a Return Merchandize Authorization Number (RMA #).
Products returned without the RMA # will be refused.
Call CHAUVET® and request an RMA # prior to shipping the fixture. Be prepared to provide the
model number, serial number and a brief description of the cause for the return. Be sure to pack
fixture properly; any shipping damage resulting from inadequate packaging is the customer’s
responsibility. FedEx packing or double-boxing are recommended.
CHAUVET® reserves the right to use its own discretion to repair or replace product(s).
If you are given an RMA #, please include the following information on a piece of paper inside
the box:
1) Your name
2) Your address
3) Your phone number
4) The RMA #
5) A brief description of the symptoms
Claims Damage incurred in shipping is the responsibility of the shipper; therefore, the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.

LEDSplash 86B User Manual 12 Rev. 3
Technical Specifications
WEIGHT & DIMENSIONS
Length......................................................................................................................................................... 4.9 in (124 mm)
Width...............................................................................................................................................................6 in (153 mm)
Height.......................................................................................................................................................... 6.8 in (173 mm)
Weight...........................................................................................................................................................1.8 lbs (0.8 kg)
POWER
Auto-ranging power supply............................................................................................................100~240 VAC, 50/60 Hz
Power consumption @ 120 VAC, 60 Hz............................................................................... 9 W (0.2 A) max, 0.2 A inrush
Power consumption @ 230 VAC, 50 Hz............................................................................... 5 W (0.1 A) max, 0.1 A inrush
Power output.................................................................................................................................................... 37 units max
Fuse..................................................................................................................................................................F 1 A, 250 V
LIGHT SOURCE
LED...................................................................................................... 86 x 5 mm (44 red, 21 green, 21 blue) 100,000 hrs
PHOTO OPTIC
Luminance @ 1 m.....................................................................................................................................................530 lux
Beam Angle .................................................................................................................................................................... 19°
Field Angle...................................................................................................................................................................... 36°
THERMAL
Maximum ambient temperature.....................................................................................................................104° F (40° C)
ORDERING INFORMATION
LEDsplash™ 86B .....................................................................................................................................LEDSPLASH86B
WARRANTY INFORMATION
Warranty .......................................................................................................................................... 2-year limited warranty
Contact Us
World Wide General Information CHAUVET® Lighting
5200 NW 108th Avenue
Sunrise, FL 33351
voice: 954.929.1115
fax: [phone]
toll free: 800.762.1084
Technical Support CHAUVET® Lighting
5200 NW 108th Avenue
Sunrise, FL 33351
voice: 954.929.1115 (Press 4)
fax: [phone] (Attention: Service)
World Wide Web www.chauvetlighting.com