Chauvin Arnoux MTX 3290 User manual

C.A 527x
MX 50xx
MTX 3290
MTX 3291
ASYC IV
ENGLISH
User’s manual
CALIBRATION SET
KOMETEC Karl Oelkers e.K.
Mess- und Prüfgeräte · Shop
Mozartstr. 10 · D-88097 Eriskirch
T: 07541 / 955-1313 · F: 07541 / 955-1131
[email protected] · www.kometec.de

English
2
CONTENTS
1. CALIBRATION KIT......................................................................................................3
1.1 GETTING STARTED WITH CA 527X.................................................................................3
1.1.1 Step 1.................................................................................................................3
1.1.2 Step 2.................................................................................................................3
1.1.3 Step 3.................................................................................................................3
1.2. GETTING STARTED WITH MX 5006................................................................................4
1.2.1 Step 1..................................................................................................................4
1.2.2 Step 2................................................................................................................4
1.2.3 Step 3................................................................................................................4
1.3 GETTING STARTED WITH MX 5060.................................................................................5
1.4 GETTING STARTED WITH MX 329X.................................................................................5
2. RUNNING THE CALIBRATION PROGRAM...............................................................6
2.1. INSTALLING THE PROGRAM ...........................................................................................6
2.2. FIRST RUN ..................................................................................................................6
2.3. COM PORT.................................................................................................................9
2.4. READING THE CALIBRATION DATA ..................................................................................9
3. CALIBRATION..............................................................................................................11
3.1. OFFSET SETTING .......................................................................................................11
3.2. SLOPE SETTINGS OR GAINS SETTINGS..........................................................................11
3.3. CORRECTION FACTOR................................................................................................16
3.4. BANDWIDTH COMPENSATION ......................................................................................16
3.5. MISC.(DIVERS).........................................................................................................18
3.6. READ......................................................................................................................18
3.8. DISPLAY OFFSETS AND SLOPES..................................................................................19
3.9. RUNNING A REMOTE COMMAND ..................................................................................19
4. STORING CALIBRATION DATA.................................................................................20
5. QUITTING THE PROGRAM..........................................................................................20

English
3
3
1. CALIBRATION KIT
Equipment required:
9Calibration kit ref: P01196770 including software and interface board
9Screwdrivers: Torx 4 mm or Posidriv, depending on date of manufacture
9Calibrator: Fluke 5500, Datron 9900 or equivalent
9Test leads
9Short cord or short circuit with 19 mm spacing
1.1 Getting started with CA 527x
Unplug the test leads.
1.1.1 Step 1
1.1.2 Step 2
1.1.3 Step 3
Risk of electrical chock during the calibration process. Be careful not to
touch the multimeter inputs on the rear side.

English
4
1.2. Getting started with MX 5006
Disconnect the power supply cord and test leads.
1.2.1 Step 1
Remove the rubber feet in order to access the screws.
1.2.2 Step 2
Unscrew and separate both sides.
1.2.3 Step 3
Keep the interface board away from the power supply board (risk of electrical shock).
Position the interface board as shown below.

English
5
5
1.3 Getting started with MX 5060
1.4 Getting started with MTX 329x
* Use an USB optic cable ÍÎ.
* Connect the cable to the MTX 329x.

English
6
2. RUNNING THE CALIBRATION PROGRAM
2.1. Installing the program
Insert the CD into the PC. Run “SETUP.EXE”.
2.2. First run
Run MTX_REG_MON program.
Follow the instructions. Press “OK”.
Select the language: English...

English
7
7
Select the instrument range:
If CAxxx range, select the model:

English
8
Select CA 5271 / 73, if needed:
If MXxxxx range, select the model:
If MTXxxxx range, select the model:
E²PROM read of the CA 527x / MX 50xx / MXT 329x :
Select "NO".

English
9
9
2.3. COM port
Select the communication port: look for the COM port that corresponds to your USB cable.
Example: Windows XP config panel Æ System Hardware Æ Device manager Æ Ports
(COM and CPT). Search for CP210x in the list of COM ports. Select the
corresponding COM port in menu below.
Note : COMx searches automatically the COM corresponding to CP210x.
2.4. Reading the calibration data
After selecting the COMx, you are advised to read the data from the current calibration:
Select « Read_Ram ».
Read example for MX 5060:

English
10