Childcare DISCOVERY PRO User manual

DISCOVERY PRO
Stroller Model # 015535
IMPORTANT:
RETAIN FOR FUTURE REFERENCE, READ CAREFULLY

Always check that safety locks are engaged before placing a child in the stroller.
Ensure your child is secured with a correctly adjusted safety harness.
Do not allow children to stand on the seat.
Do not hang bags or goods from the handle as this could cause the stroller to tip over.
Do not place more than 5kgs in the basket or 1kg in the hood pocket (if supplied).
The weight of the child using the product should not exceed 20kgs.
The height of the child using the product should not exceed 96cm.
It is unsafe to use parts other than those approved by the manufacturer.
Never ride with more than one child in the stroller.
Regularly inspect all parts and locking devices, promptly replace worn out or broken parts.
Remove the child from the stroller before going up or down stairs and escalators.
To prevent the risk of the stroller catching re, do not park it near an open re, heater or barbeque.
Do not make any changes or alterations to this product, unless through an approved service agent.
To avoid the risk of suffocation, keep all plastic packaging materials out of reach of children.
Never leave safety harness connected when not tted to a child in the stroller as this may create
loops that could cause a strangulation hazard.
Read all instructions before assembly and use of the stroller. Keep
instructions for future use.
Safety Precautions
TO AVOID INJURY OR DEATH:
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER
IS STATIONARY.
DO NOT LEAVE CHILD UNATTENDED.
SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS
STROLLER.
MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING
PARTS IF YOU ADJUST THE STROLLER.
WARNING

03
Due to variations in the style and design of our products, the photographs and illustrations
shown in this instruction manual are generic, therefore product fabrics, colour and
design may vary from images shown. CNP Brands reserves the right to alter product
specications without notice as a result of our ongoing policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Childcare Stroller
Congratulations on your purchase of the
Childcare Discovery Pro Stroller.
This product has been designed and developed with
safety, comfort and functionality in mind. Please take
the time to read this manual carefully before using
this product and keep it in a safe place for future
reference.

04
x2
x2
x1
x4
x2
x2
x1
Assembly Contents
Check what you have received...
You have received 1 box. Please check the contents of the box against the list below. If anything is
missing, please contact Customer Service. In Australia, contact CNP Brands on 1300 667 137, in
New Zealand contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
Dual front swivel wheel
Rear wheel
Rear axle with brake bar
Washer
Collet and collet cover
Wheel hub cap (for rear wheels)
Bumper bar

05
Assembly / Operating Instructions
Assembly Contents
Reversible bootcover
Stroller frame, with the following components
pre-assembled on frame:
Canopy
Reversible seat pad insert
Five point safety harness
Basket
Unfolding the stroller
1. Simultaneously lift the stroller
handle slightly while pressing
down on the folding lock
(highlighted in the image). When
opened the stroller the frame will
“click” and lock into position.
Ensure the stroller is locked on
both sides before use.
Unlock
Dual front swivel wheels assembly
1. Ensure the swivel lock is unlocked by pushing it downwards to
the lowest point.
x1

06
Assembly / Operating Instructions
To use front brakes
1. To lock brakes, push down on
each brake lever with foot.
2. To release brakes, lift each brake
lever up with foot.
CAUTION: Always apply both brakes
when parking stroller.
Rear wheels assembly
1. Turn stroller over.
2. Assemble the rear axle onto the stroller frame by gently pushing
down until the rear brakes “click” and lock into position on both
rear legs.
Swivel function
1. To lock swivel wheels, push lever
up
2. To unlock swivel wheels, push
lever down.
Lock
Lock
Unlock
Unlock
2. Push front wheels onto the stroller frame legs until they “click”
_____into position. Ensure the red brake is facing away.
3. Ensure the wheels are securely attached to the stroller frame
_____legs by pulling them downwards before use.
HELPFUL HINTS
To make it easier to steer we highly recommend that only two wheels
be in a swivel motion at any time (regardless of handle position).

07
Rear brake
assembly Rear wheel
Washer
Collet
Collet
cover
Wheel
hub cap
Assembly / Operating Instructions
Using the rear brakes
1. To lock the brakes, push down on the brakes bar on the rear
axle with foot.
2. To unlock brakes, lift the brake bar on the rear axle with foot.
CAUTION: Always apply both front and rear brakes when parking
stroller.
3. Slide a washer onto the read axle.
4. Insert the rear wheel after the washer.
5. Place another washer after the rear wheel.
6. Fit a collet after the washer. Ensure that the key in the slot of the
_____collet is correctly located in the axle’s groove.
7. Fit the collet cover to the collet by rmly pressing the collet
_____cover into place
8. Push the wheel hub cap onto the wheel hub.
9. Repeat for other wheel.

08
Assembly / Operating Instructions
Attaching bumper bar
1. Align the bumper bar ends with the locking buttons on the sides
of armrest moulds of the stroller frame, then slide both bumper
bar ends forward while pressing the locking buttons in until they
“click” and lock into position on each side.
2. To remove bumper bar; push each locking button in and pull
bumper bar out.
Forward facing mode
When the stroller is in Forward facing mode, ensure the swivel
function on both dual front swivel wheels and the brake bar on the
rear axle are unlocked.
WARNING: On unmade or uneven surfaces all swivels must be locked.
Locking button
Reversing handle
1. To reverse handle, pull up on both handle reverse levers situated
on each side of handle.
2. Reverse handle and lock it into position.
Reverse handle mode
When the stroller is in Reverse handle mode, dual front swivel wheels
must be turned around to the trailing position and swivel locks
engaged on both wheels.
Handle reverse
lever

09
Assembly / Operating Instructions
Adjusting the backrest
This stroller has an adjustable backrest. The upright position on the
backrest is not suitable for use with children less than six months old.
For use with a newborn (0-6mths), the seat should be fully reclined.
The backrest should only be adjusted to a more upright position
as the child grows older and is able to support their head without
assistance.
1. To lower the backrest; pull backrest adjusting lever upwards and
lower to desired position. Release lever.
2. To raise the backrest; pull backrest adjusting lever upwards and
push backrest up to desired position. Release lever.
CAUTION: Do not adjust the backrest while child is in the stroller.
To adjust the seat extension
1. Lower the seat extension by pressing up the release latches
located underneath on both sides of the seat extension and
push down.
2. Raise the seat extension by pressing up the release latches and
lift up untl the release latches lock into place.
To adjust canopy
1. To open the canopy, pull forward.
2. To close the canopy, pull back.
CAUTION: The canopy must be fully closed before folding the
stroller.
Backrest adjusting lever

10
Assembly / Operating Instructions
Restraints - Harness
1. To secure the child in the harness, place left
hand buckle prong (b) on top of (a).
2. Hold both left hand buckle prongs (a) and (b)
together and insert it into buckle housing (e)
until it snaps into position.
3. Repeat previous steps for right hand buckle
prongs (c) and (d).
4. Once all attached, carefully adjust the harness
straps by pulling each slider (f) until the desired
t is achieved in the lap, shoulder and crotch
straps.
5. To release the buckles, squeeze the top and
bottom prongs (a) and (b), (c) and (d) together
until harness disengages.
CAUTION: Always adjust the harness when
changing the seating position of the child.
Top strap
Bottom
strap
To adjust waist strap
1. To loosen waist strap, push up both top and
bottom straps through buckle as circled in
diagram.
2. To place waist strap in desired position, slide
the bottom strap into position then pull the top
strap and tighten into position.
(a), (b): Left hand buckle prongs
(c), (d): Right hand buckle prongs
(e): Buckle housing
(f): Strap adjustment sliders
Mesh canopy extension
1. Unzip the rear section of the canopy to use the mesh canopy
extension. Zip when not in use.
CAUTION: The canopy must be fully closed before folding the
stroller.
f
ff
ff
a
b
c
d
e

11
Assembly / Operating Instructions
Bootcover
1. To attach bootcover, raise seat extension and attach press
studs underneath the seat extension to the matching press
studs on the inside of the bootcover as shown in image.
2. Insert the top ap of the
bootcover underneath the
bumper bar.
3. Insert the two elastic toggles into
the seat liner’s side slots on both
sides to secure it into place.
4. Attach the toggle on the top ap
of the bootcover to the loop to
secure it in place.
WARNING: Always remove bootcover before folding the stroller.
Tether strap
Ensure tether strap is used at all times. Make sure your hand is fed
through the loop as shown in the diagram.
Reversing seat pad
1. Unclip the two press studs on the behind of the backrest.

12
Assembly / Operating Instructions
Attaching infant carrier to stroller
This stroller is designed for use with Britax (Orion/Strider/Cruiser)
infant carrier.
1. Remove armrest’s fabric cover by:
• Hold the fabric cover rmly and pull it away from the
armrest to release the rst plastic peg (located underneath
the fabric cover).
To remove
rst plastic peg
To remove
second plastic peg
To remove
third plastic peg
• Then slide the fabric cover
towards the backrest of
the stroller and pull out to
release the second and
third plastic pegs. This will
allow the fabric cover to be
detached from the armrest
completely.
2. Pull out all ve straps of the ve point safety harness from the
slots in the seat pad.
3. Reverse seat pad
4. Re-thread all ve straps of the ve point safety harness into the
ve slots in the seat pad.
5. Attach two press studs on the behind of the backrest.
Reversing seat pad (continued)

13
Assembly / Operating Instructions
2. Open the plastic slot cover on the
_____armrest by pushing it upwards and
_____then opening it downwards.
3. Repeat previous steps for the __
fffff____opposite armrest.
4. Insert the infant carrier into the armrest slots so orientation
_____matches image (right).
Attaching infant carrier to
stroller (cont.)
Locking levers
5. Push both of the locking levers on the handle of the infant
_____carrier in and swing handle down until it “clicks” and locks into
_____place.
WARNING: Ensure the infant carrier is fully engaged and locked into
stroller armrests before use.

14
Assembly / Operating Instructions
4. Attach armrest fabric cover by:
• Sliding the fabric cover towards the bumper bar and press in to attach the second and
third plastic pegs (located underneath the fabric cover).
• Hold the fabric cover rmly and press in to attach the rst plastic peg. This will allow the
fabric cover to attach to the armrest completely.
To attach
rst plastic peg
To attach second
plastic peg
WARNING: To avoid injury, ensure both armrest’s plastic slot covers and fabric
covers are securely attached before placing baby in stroller.
To attach
third plastic peg
To remove infant carrier from stroller
1. Push both of the locking levers on the handle of the infant
carrier in and swing handle up until it “clicks” and locks into
place..
2. Lift the infant carrier upwards to remove from the armrest slots.
3. Close both armrest plastic slot covers. Ensure they are locked
into position by pushing them down into place.

15
Assembly / Operating Instructions
Folding the stroller
1. Before folding the stroller, remove bootcover, close the hood,
place seat in full layback position and transfer handle to forward
facing mode.
2. Simultaneously squeeze both handle levers located in the
middle of the stroller handle and lift the red lever located on the
left side of the stroller handle.
3. Push down on handle to commence folding the unit. Once fold
is complete, push down on the handle to engage the folding
locks.
How to care for your Childcare stroller
Cleaning
To ensure the long-lasting use of your stroller, dry it with a soft absorbent cloth after use in rainy
weather. Use a damp cloth to clean the frame. Do not use abrasive cleaners. After using your
stroller on the beach, clean the frame and wheels thoroughly with water to remove the sand and
salt. Allow it to dry thoroughly. Removable and non-removable fabric covers and trims maybe
cleaned using a damp cloth with soap or mild detergent. Allow it to dry completely before folding
or storing it away. Do not dry clean, or use bleach on fabrics or trims. Do not machine wash,
tumble or spin dry, unless the care labelling on the product permits these methods.
Maintenance
Check stroller regularly to ensure that locking devices and components are secure and working
properly. Always check parts regularly for tightness of screws, nuts and other fasteners – tighten or
replace if required. To maintain the safety of your stroller, seek prompt repairs for bent, torn, worn
or broken parts. Use only those parts and accessories approved by CNP Brands. If the wheels
squeak, use silicone based spray or light oil ensuring it penetrates the wheel and axle assembly.
To prevent mould or mildew, do not fold or store the product if it is damp or wet. Allow it to dry
thoroughly. Always store the product in a well ventilated area and away from direct sunlight.
If you have any difculties in assembling the stroller, please contact our Service Department. In
Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution
on 0800 567 5000.

16
Distributed in Australia by CNP Brands, 20 Calarco Drive, VIC, 3030
Customer Service 1300 667 137 www.cnpbrands.com.au
Distributed in New Zealand by Wainhouse Distribution, 2-6 Argyle St,
Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand
Customer Service: 0800 567 5000 [email protected]