Childcare vector pro 015616 User manual

VECTOR PRO
Stroller Model # 015616
IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY

Fingers or parts of the body could be injured when the stroller is being folded or unfolded. Please
use caution when folding or unfolding the stroller.
Check that all safety locks are engaged before placing a child in the stroller.
Ensure your child is secured with a correctly adjusted safety harness.
Do not allow children to stand on the seat.
Do not hang bags or goods from the handle as this could cause the stroller to tip over.
Do not place more than 5kgs in the basket or 1kg in the hood pocket (if supplied).
The weight of the child using the product should not exceed 20kgs.
The height of the child using the product should not exceed 96cm.
Use original accessories and manufacturer approved parts only.
Never ride with more than one child in the stroller.
Always use safety locks.
Promptly replace worn out or broken parts.
Remove the child from the stroller before going up or down stairs and escalators.
To prevent the risk of the stroller catching re, do not park it near an open re, heater or barbeque.
Do not make any changes or alterations to this product, unless through an approved service agent.
To avoid the risk of suffocation, keep all plastic packaging materials out of reach of children.
Never leave safety harness connected when not tted to a child in the stroller as this may create
loops that could cause a strangulation hazard.
Ensure the storage latch is fully closed when lifting or carrying the stroller.
Read all instructions before assembly and use of the stroller. Keep
instructions for future use.
Safety Precautions
TO AVOID INJURY OR DEATH:
FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER
IS STATIONARY.
USE THE TETHER STRAP AT ALL TIMES TO PREVENT THE
STROLLER ROLLING AWAY.
DO NOT LEAVE CHILD UNATTENDED.
SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS
STROLLER.
MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING
PARTS IF YOU ADJUST THE STROLLER, OTHERWISE THEY
MAY BE INJURED.
WARNING

03
Due to variations in the style and design of our products, the photographs and illustrations
shown in this instruction manual are generic, therefore product fabrics, colour and
design may vary from images shown. CNP Brands reserves the right to alter product
specications without notice as a result of our ongoing policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Childcare Stroller
Congratulations on your purchase of the
Childcare Vector Pro Stroller.
This product has been designed and developed with
safety, comfort and functionality in mind. Please take
the time to read this manual carefully before using
this product and keep it in a safe place for future
reference.

04
Supplied loose in box:
Dual swivel wheels
Reversible bootcover
Bumper bar
Stroller frame, with the following components
pre-assembled on frame:
Canopy
Basket
Reversible seat pad
x4
x1
x1
Assembly Contents
Check what you have received...
You have received 1 box. Please check the contents of the box against the list below.
If anything is missing, please contact Customer Service. In Australia, contact CNP
Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution on 0800
567 5000.

05
Assembly / Operating Instructions
Unfolding the stroller
1. Release the folding lock as high-
lighted in the image right.
2. Lift handle and seat apart until the
frame clicks and locks on both
sides.
3. Ensure the stroller is locked on
both sides before using.
Front / rear swivel wheels assembly
1. Make sure the swivel lock is unlocked by pushing down to
lowest point.
2. The wheel should be assembled with the swivel housing facing
upwards as shown in image. Unlock
3. Push forward and hold the wheel fastening clip. Whilst holding
this clip, push the wheel into position on the metal shaft, release
fastening clip so the wheel can click into position.
4. Pull the wheel downwards to make sure it is securely attached
to the stroller legs before using.

06
Assembly / Operating Instructions
To use bumper bar
1. Align bumper bar ends with slots on the arm rest of the stroller
frame, then slide both bumper bar ends until it clicks into place.
2. To remove bumper bar, push each button located on the side of
armrest area and pull bumper bar out.
Swivel function
1. To lock swivel wheels, push lever up
2. To unlock swivel wheels, push lever down.
HELPFUL HINTS
To make it easier to steer we highly recommend that only two wheels
be in a swivel motion at any time (regardless of handle position).
Lock
Unlock
To use brakes
1. To lock brakes, push down on each brake lever with foot.
2. To release brakes, lift each brake lever up with foot.
CAUTION: Always apply both brakes when parking stroller.

07
To adjust the seat extension
1. Lower the seat extension by pressing up the release latches
located underneath on both sides of the seat extension and
push down. Then push leg support down.
2. Raise the seat extension by pressing up the release latches and
lift up until the release latches lock into place.
Assembly / Operating Instructions
Positioning backrest
1. To lower backrest, lift backrest adjusting lever.
2. Lower backrest to desired position.
3. To raise, simply push backrest up
CAUTION: Do not adjust the backrest while the child is in the stroller
Restraints - Harness
1. To secure the child in the harness, place left
hand buckle prong (b) on top of (a).
2. Hold both left hand buckle prongs (a) and (b)
together and insert it into buckle housing (e)
until it snaps into position.
3. Repeat previous steps for right hand buckle
prongs (c) and (d).
4. Once all attached, carefully adjust the harness
straps by pulling each slider (f) until the desired
t is achieved in the lap, shoulder and crotch
straps.
5. To release the buckles, squeeze the top and
bottom prongs (a) and (b), (c) and (d) together
until harness disengages.
CAUTION: Always adjust the harness when
changing the seating position of the child.
f
ff
ff
a
b
c
d
e
(a), (b): Left hand buckle prongs
(c), (d): Right hand buckle prongs
(e): Buckle housing
(f): Strap adjustment sliders
PLEASE NOTE: This stroller has an adjustable backrest. The upright position on the backrest
is not suitable for use with children less than six months old. For use with a newborn (0-6
mths), the seat should be fully reclined. The backrest should only be adjusted to a more upright
position as the child grows older and is able to support their head without assistance.

08
Assembly / Operating Instructions
Using four wheel steering
This unit has a reversing handle with four swivel wheels.
PLEASE NOTE: To make it easier to steer we highly recommend that only two wheels be in a
swivel motion at any time (regardless of handle position) and the correct set-up as follows:
Reversing handle
1. To reverse handle, pull up on both handle reverse levers situated
on each side of handle.
2. Reverse handle and lock it into position.
Forward facing mode
1. The swivels under the handle must be locked with the brake
lever facing the user.
2. Swivels furthest away from user are left in the unlocked position,
allowing them to swivel
WARNING: On unmade or uneven surfaces all swivels must be locked.
Reverse handle mode
1. The swivels under the handle must be locked with the brake
lever facing the user.
2. Swivels furthest away from user are left in the unlocked position,
allowing them to swivel.
Handle reverse lever

09
To adjust canopy
1. To open canopy, pull forward.
2. To close canopy, pull back.
CAUTION: The canopy must be fully closed before folding the stroller
Mesh canopy extension
Unzip the rear section of canopy to use the mesh canopy extension.
Zip extension closed when not in use
Assembly / Operating Instructions

10
Assembly / Operating Instructions
Bootcover
1. To attach bootcover, raise seat extension and attach press
studs underneath the seat extension to the matching press
studs on the inside of the bootcover as show in diagram.
2. Insert the top ap of the bootcover underneath the bumper bar
and insert the elastic loops into the seat liner’s side slots on
both sides to secure it in place.
3. Attach the toggle on the top ap of
the bootcover to the loop to secure
it in place.
WARNING: Always remove bootcover
before folding the stroller.
Tether strap
Ensure tether strap is used at al times. Make sure your hand is fed
through the loop as shown.

11
Assembly / Operating Instructions
Folding the stroller
1. Before folding the stroller, remove bootcover, close the hood,
place seat in full layback position and transfer handle to rear
(forward facing mode).
2. Simultaneously lift the red levers located on both sides of the
stroller. Push down on handle to commence folding the unit.
3. Once fold is completed, the folding lock will automatically
engage.
Reversing seat pad
1. Unclip the two press studs on the rear of the backrest.
2. Pull out all ve straps of the ve point safety harness from the
slots in the seat pad.
3. Reverse seat pad
4. Re-thread all ve straps of the ve point safety harness into the
ve slots in the seat pad.
5. Attach two press studs on the behind of the backrest.

12
2. Open the plastic slot cover on the armrest by pushing it
upwards and then opening it downwards.
3. Repeat previous steps for the opposite armrest.
Assembly / Operating Instructions
Attaching infant carrier to stroller
This stroller is designed for use with Britax (Orion/Strider/Cruiser)
infant carrier.
1. Remove armrest’s fabric cover by:
• Holding the fabric cover rmly and pull it away from the
armrest to release the rst plastic peg (located underneath
the fabric cover).
• Then slide the fabric cover towards the backrest of the
stroller and pull out to release the second and third plastic
pegs. This will allow the fabric cover to be detach from the
armrest completely.
To remove
rst plastic peg
To remove
second plastic peg
To remove
third plastic peg

13
4. Insert the infant carrier into the armrest slots so orientation
matches photo (right).
5. Push both of the locking handles of the infant carrier in (a) and
swing handle down until you hear the lock ‘click’ into place (b).
WARNING: Ensure the infant carrier is fully engaged and locked into
stroller armrests before use.
Assembly / Operating Instructions
Attaching infant carrier to stroller (cont.)
(b)
(a)
To remove infant carrier from stroller
1. Push both of the locking handles of the infant carrier in (a) and
swing handle up until you hear the lock ‘click’ into place (b). (a)
(b)
2. Lift the infant carrier upwards to remove from the armrest slots.

14
To remove infant carrier from stroller (cont.)
4. Attach armrest fabric cover by:
• Sliding the fabric cover towards the bumper bar and press
in to attach the second and third plastic pegs (located
underneath the fabric cover).
• Holding the fabric cover rmly and press in to attach the
rst plastic peg. This will allow the fabric cover to be attach
to the armrest completely.
WARNING: To avoid injury, ensure both armrest’s plastic slot covers
and fabric covers are securely attached before placing baby in
stroller.
To attach
rst plastic peg
To attach
third plastic peg
To attach second
plastic peg
Assembly / Operating Instructions
3. Close both armrest plastic slot covers. Ensure they are locked
into position by pushing it down into place.

15
How to care for your Childcare stroller
Cleaning
To ensure the long-lasting use of your stroller, dry it with a soft absorbent cloth after use in
rainy weather. Use a damp cloth to clean the frame. Do not use abrasive cleaners. After using
your stroller on the beach, clean the frame and wheels thoroughly with water to remove the
sand and salt. Allow it to dry thoroughly. Removeable and non-removeable fabric covers and
trims maybe cleaned using a damp cloth with soap or mild detergent. Allow it dry completely
before folding or storing it away. Do not dry clean, or use bleach on fabrics or trims. Do not
machine wash, tumble or spin dry, unless the care labelling on the product permits these
methods.
Maintenance
Check stroller regularly to ensure that locking devices and components are secure and
working properly. Always check parts regularly for tightness of screws, nuts and other
fasteners – tighten or replace if required. To maintain the safety of your stroller, seek prompt
repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by
CNP Brands. If the wheels squeak, use silicone based spray or light oil ensuring it penetrates
the wheel and axle assembly. To prevent mould or mildew, do not fold or store the product if
it is damp or wet. Allow it to dry thoroughly. Always store the product in a well ventilated area
and away from direct sunlight.
If you have any difculties in assembling the stroller, please contact our Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse
Distribution on 0800 567 5000.

16
Distributed in Australia by CNP Brands, 20 Calarco Drive, VIC, 3030
Customer Service 1300 667 137 www.cnpbrands.com.au
Distributed in New Zealand by Wainhouse Distribution, 2-6 Argyle St,
Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand
Customer Service: 0800 567 5000 [email protected]