Childcare ECHO 015256 User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
ECHO
Stroller Model # 015256

03
Due to variations in the style and design of our products, the photographs and illustrations
shown in this instruction manual are generic, therefore product fabrics, colour and
design may vary from images shown. CNP Brands reserves the right to alter product
specications without notice as a result of our ongoing policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Childcare Stroller
Congratulations on your purchase of the
Childcare Echo Stroller.
This product has been designed and developed with
safety, comfort and functionality in mind. Please take
the time to read this manual carefully before using
this product and keep it in a safe place for future
reference.
Fingers or parts of the body could be injured when the stroller is being folded or unfolded. Please
use caution when folding or unfolding the stroller.
Check that all safety locks are engaged before placing a child in the stroller.
Ensure your child is secured with a correctly adjusted safety harness.
Do not allow children to stand on the seat.
Do not hang bags or goods from the handle as this could cause the stroller to tip over.
Do not place more than 3kgs in the basket or 1kg in the hood pocket (if supplied).
The weight of the child using the product should not exceed 17kgs.
The height of the child using the product should not exceed 96cm.
Use original accessories and manufacturer approved parts only.
Never ride with more than one child in the stroller.
Always use safety locks.
Promptly replace worn out or broken parts.
Remove the child from the stroller before going up or down stairs and escalators.
To prevent the risk of the stroller catching re, do not park it near an open re, heater or barbeque.
Do not make any changes or alterations to this product, unless through an approved service agent.
To avoid the risk of suffocation, keep all plastic packaging materials out of reach of children.
Never leave safety harness connected when not tted to a child in the stroller as this may create
loops that could cause a strangulation hazard.
Ensure the storage latch is fully closed when lifting or carrying the stroller.
The vehicle is designed for use on at or gently sloping surfaces and may be unstable on higher
and uneven surface, otherwise there may be a possibility of tipping.
Read all instructions before assembly and use of the stroller. Keep
instructions for future use.
Safety Precautions
WARNING
TO AVOID INJURY OR DEATH:
FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER
IS STATIONARY.
USE THE TETHER STRAP AT ALL TIMES TO PREVENT THE
STROLLER ROLLING AWAY.
DO NOT LEAVE CHILD UNATTENDED.
SECURE THE CHILD IN THE HARNESS AT ALL TIMES.
DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS
STROLLER.
MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING
PARTS IF YOU ADJUST THE STROLLER, OTHERWISE THEY
MAY BE INJURED.

0504
Supplied loose in box:
Stroller Frame
Canopy
Handle
Front Swivel Wheels
Back Wheels
Bumper bar
Boot cover
x1
x1
x1
x2
x2
x1
x1
Assembly Contents Assembly Contents
Check what you have received...
You have received 1 box. Please check the contents of the box against the list below. If anything is
missing, please contact Customer Service. In Australia, contact CNP Brands on 1300 667 137, in
New Zealand contact Wainhouse Distribution on 0800 567 5000.

0706
2. The rear wheels are distinguished by the holes on the top of the
wheel as seen in image.
3. Push in pop pin whilst pushing downward. Ensure the pop pin
‘clicks’ into place.
Pull the wheel downwards to make sure it is securely attached
to the stroller legs before using.
Front swivel / rear wheels assembly
1. Push front wheel rmly onto the mounting point of the swivel
front legs, located just above the footrest. Ensure the brake is
facing down to ensure wheel is tted correctly. Push down until
the wheel clicks into position. Repeat for the other front wheel.
Pull the wheel downwards to make sure it is securely attached
to the stroller legs before using.
Assembly / Operating Instructions Assembly / Operating Instructions
Rear wheel indication
Swivel function
1. To lock swivel wheels, push lever up
2. To unlock swivel wheels, push lever
down.
Lock Unlock
To use brakes
1. To lock brakes, push down on each
brake lever with foot.
2. To release brakes, lift each brake lever
up with foot.
CAUTION: Always apply both brakes when
parking stroller.
Lock Unlock

0908
Assemble Handle
1. Ensure the bottom of the handle lines up with the bracket.
The bracket should be on a 45 degree angle before the
handle is inserted.
2. Push down handles until the pop pins either side of the frame
click into place.
Assembly / Operating Instructions Assembly / Operating Instructions
Unfolding the stroller
1. Push lever to the side to whilst simultaneously squeezing the
handle lock located in the centre of the handle.
2. Pull the handle up to open the stroller unit. Pull in a short
sharp motion to ensure the stroller locks into the open
position.
Ensure this sits at a 45 degree angle
Folding the stroller
1. Before folding the stroller, close the hood and place seat in full
lay back position and transfer handle to forward facing mode.
Push lever to the side to whilst simultaneously squeezing the
handle lock located in the centre of the handle.
2. Push the handle forward to collapse stroller unit. Push down
until the stroller frame clicks into a locked position.

1110
Assembly / Operating Instructions Assembly / Operating Instructions
Reversing handle
1. To reverse handle, pull up on both handle reverse levers situated
on each side of handle.
2. Reverse handle and lock it into position.
Handle reverse lever
Inserting the bumper bar
1. Align bumper bar ends with slots on the arm rest of the stroller
frame. Push in the push pins then slide both bumper bar ends
until it clicks into place.
2. To remove bumper bar, push each button located on the side of
armrest area and pull bumper bar out.
Attaching the canopy
1. Line up the canopy with the frame as per image. Push into the
frame until both sides click into place and are secure.
Push in button
Removing the canopy
1. Push in both button’s simultaneously, located on the inside
where the canopy is inserted. Pull canopy out of tubing.
2. Ensure press stud buttons are
secure. These are located on the
underside of the canopy.

1312
To adjust the seat extension
1. Lower the seat extension by squeezing the bar located
underneath the foot rest. By squeezing this bar, it will release the
footrest. Push down gently on the footrest to lower.
2. Raise the seat extension by squeezing the bar and lifting up until
the release latches lock into place.
Assembly / Operating InstructionsAssembly / Operating Instructions
Restraints - Harness
1. To secure the child in the harness, place left
hand buckle prong (b) on top of (a).
2. Hold both left hand buckle prongs (a) and (b)
together and insert it into buckle housing (e)
until it snaps into position.
3. Repeat previous steps for right hand buckle
prongs (c) and (d).
4. Once all attached, carefully adjust the harness
straps by pulling each slider (f) until the desired
t is achieved in the lap, shoulder and crotch
straps.
5. To release the buckles, squeeze the top and
bottom prongs (a) and (b), (c) and (d) together
until harness disengages.
CAUTION: Always adjust the harness when
changing the seating position of the child.
f
ff
ff
a
b
c
d
e
(a), (b): Left hand buckle prongs
(c), (d): Right hand buckle prongs
(e): Buckle housing
(f): Strap adjustment sliders
Canopy functions
1. Pull the canopy cover forward or push backward.
2. Pull out the visor as per image for the sun visor function.
CAUTION: The canopy must be fully closed before folding the
stroller

1514
Assembly / Operating Instructions Assembly / Operating Instructions
Forward facing mode
When the stroller is in forward facing mode, ensure the swivel
function on both dual front
WARNING: On unmade or uneven surfaces all swivels must be locked.
Reverse handle mode
1. The swivels are now situated under the handle.
2. The front xed wheels are xed.
1. To decline the seat adjuster, squeeze the clasp to release and
pull in a downward motion. Lower to desired position.
Inclining the
seat adjuster
Declining the
seat adjuster
2. To incline the seat adjuster; hold both straps and push the
clasp whilst sliding upward to desired position.
CAUTION: Do not adjust the backrest while child is in the stroller.
Adjusting the backrest
This stroller has an adjustable backrest. The upright position on the backrest is not suitable for use
with children less than six months old.
For use with a newborn (0-6mths), the seat should be fully reclined. The backrest should only
be adjusted to a more upright position as the child grows older and is able to support their head
without assistance.

1716
Assembly / Operating Instructions
Tether strap
Ensure tether strap is used at all times. Make sure your hand is fed
through the loop as shown.
Boot cover
1. Wrap the boot cover around the bottom end of the bassinet or
seat. Attach press studs as shown in image. Match to the press
studs on the inside of the boot cover as shown.
2. Insert the top ap of the boot cover
underneath the bumper bar so it sits
on top of the boot cover.
3. Push rmly on the press studs of
both sides to secure it into place.
WARNING: Always remove boot cover before folding the stroller.
How to care for your Childcare stroller
Cleaning
To ensure the long-lasting use of your stroller, dry it with a soft absorbent cloth after use in
rainy weather. Use a damp cloth to clean the frame. Do not use abrasive cleaners. After using
your stroller on the beach, clean the frame and wheels thoroughly with water to remove the
sand and salt. Allow it to dry thoroughly. Removable and non-removeable fabric covers and
trims maybe cleaned using a damp cloth with soap or mild detergent. Allow it dry completely
before folding or storing it away. Do not dry clean, or use bleach on fabrics or trims. Do not
machine wash, tumble or spin dry, unless the care labelling on the product permits these
methods.
Maintenance
Check stroller regularly to ensure that locking devices and components are secure and
working properly. Always check parts regularly for tightness of screws, nuts and other
fasteners – tighten or replace if required. To maintain the safety of your stroller, seek prompt
repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by
CNP Brands. If the wheels squeak, use silicone based spray or light oil ensuring it penetrates
the wheel and axle assembly. To prevent mould or mildew, do not fold or store the product if
it is damp or wet. Allow it to dry thoroughly. Always store the product in a well ventilated area
and away from direct sunlight.
If you have any difculties in assembling the stroller, please contact our Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse
Distribution on 0800 567 5000.