Circontrol Wallbox eNext Series User manual

Installation Manual
Wallbox
eNext
Series

WallBox eNext Series Installation Manual

Wallbox eNext Series
Installation Manual
COPYRIGHT INFORMATION
This document is copyrighted, 2019 by Circontrol, S.A. All rights are reserved.
Circontrol, S.A. reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual can be reproduced, copied, translated or transmitted in
any form or by any means without the prior written permission of the original
manufacturer. Information provided in this manual is intended to be accurate
and reliable. However, the original manufacturer assumes no responsibility
for its use, or for any infringements upon the rights of third parties athat may
result from its use.
All other product names or trademarks are properties of their respective
owners.

WallBox eNext Series Installation Manual

01
1 — So, hello!
2 — Before the
installation
3 — Overview
4 — Dimensions
5 — Installation
6 — Technical Data
7 — Need Help?
Here’s your guide
to install eNext.
02
04
06
08
10
20
22

02
WallBox eNext Installation Manual
1

03
This manual provides commissioning information about Wallbox eNext,
which has been designed and tested to allow electric vehicle charging,
specified in IEC 61851.
This document has different sections such as step-by-step installation
procedure and technical data.
ELECTRICAL RISK
Necessary precautions shall be taken to prevent any electrical
risk while the operations are carried out within the unit.
Unit must be disconnected from any power source during
commissioning.
ATTENTION!
Indicates that damage to property can occur if appropriate
precautions are not taken.
So, hello!
THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT
SAFETY INFORMATION IN THIS DOCUMENT
• Complies with IEC 61851, Electric vehicle conductive
charging system (IEC 61851-1 and IEC 61851-22).
• Complies with IEC 62196, Plugs, socket-outlets, vehicle
couplers and vehicle inlets (IEC and IEC 62196-2).
• Standards: 2014/35/UE, LVD;2014/30/UE, EMC.

04
WallBox eNext Installation Manual
The charge point is designed for installation in indoor and outdoor areas. For each of
the different conditions of installation, the unit must be installed safely and assuring
the adequate protections.
• Charge point must not be installed
in areas where potential risk of
explosions are.
• Do not install the charge point
where falling objects may damage
the equipment.
• The surface where the charge
point is placed must withstand the
mechanical forces.
• This unit is no shall be used for
anything other purpose than
electric vehicle charging modes as
are expected in IEC 61851.
• Do not modify this unit. If
modified, Circontrol will reject all
responsibility and the warranty will
be void.
• Comply strictly with electrical
safety regulations according to your
country.
• Do not use any adapter, except those
approved by the EV manufacturer
• Do not perform any repair o
manipulation of the unit while it is
energized.
• Only trained and qualified personnel
should be able to access to low-
voltage electrical parts inside the
unit.
• Check the installation annually by
qualified technician.
• Remove from service any item
which have a fault that could be
dangerous for users (broken plugs,
caps that don’t close...).
• Use only Circontrol supplied spare
parts.
• Do not use this product if the
enclosure or the EV connector is
broken, cracked, open, or shows
any other indication of damage.
IMPORTANT SAFETY INSTRUCTIONS
Read carefully all the instructions before starting in or-
der to ensure properly installation of the charge point.
2
Refer to TECHNICAL DATA section for more information about environmental
installation conditions.

05
ELECTRICAL WIRING CONSIDERATIONS
Take into consideration this section before starting
wiring connections of the charge point.
Before the installation
1 — ELECTRICAL PROTECTIONS
Charge point may not include elements of electrical protection.
If this equipment has internal electrical protections, are installed in each socket-
outlet for the protection of the user against an electrical failure, according to the
international standard IEC 61851-1:2017.
In order to guarantee the total protection of the users and the installation (power
supply line included) in front of any electrical hazard, install a main circuit breaker
(MCB) and a residual current device (RCD) upstream of the charger is mandatory.
These electrical protections and the rest of the installation have to be aligned with
the local and national rules. The selectivity of the protections has to be guaranteed
at all times.
2 — POWER SUPPLY LINE DIMENSIONING
The dimensioning of the input power supply line of the charge point must be checked
by a qualified electrician. Note that several factors such as cable length between
distribution board and charge point, maximum output current of the charge point
may influence the criteria of cable selection.
In such cases, increasing the cable cross-section is required to adapt the temperature
resistance of the power supply line.
3 — MAXIMUM OUTPUT CURRENT
Please refer to the TECHNICAL DATA section to consult the default factory settings
from maximum output current of the charge point.
If the power supply is lower than maximum output current, it is necessary to adjust the
nominal current. To perform this adjustment, please refer to the INSTRUCTION MANUAL.
This value may vary depending on the model.

06
WallBox eNext Installation Manual
3
What’s included:
Charge Point Installation
Manual
2.5 mm
Allen wrench Identification
label

07
Overview
1 — LED beacon
2 — Cable glands
3 — Plugs*
4 — Wall support holes
5 — Closing box holes
(*) Plugs may vary depending on the model
1
2
3
52
4
4
4
5

08
WallBox eNext Installation Manual
4
Dimensions in mm
200
335 335
200
335

09
Dimensions
168
11562 5353 53
32
40
255
21
10

10
WallBox eNext Installation Manual
5
Material:
Tap drill 6/8M
Tools:
• Allen wrench of 2,5 mm is included in the installation kit.
• Screws, sealing washers and plastic anchors are not included.
• The fastening system of the charge point has been designed to be
installed on a wall.
»This system has been tested on a concrete wall, to be securely
fixed in such conditions is recommended to use:
3 x Inox A2 wall screws: DIN 7982 Ø4,8x38 or DIN 7981 Ø4,8x38
3 x plastic anchors: 6x40 or 8x40
»If the wall surface has different properties, the screws and plastic
anchors must be defined by a qualified installer.
Screw driver DrillerRatchet*
2.5mm Allen
(*) Ratchet tool can be used to open/close the charge point if the conditions of the installation
requiers it

11
Installation
ARequirements
• Please comply accordingly to your country specifications.
• The charge point shall be installed on the wall. The only exception is to use
accessories designed by Circontrol.
• When installing the unit, some space shall be reserved for usability, maintenance
and safety reasons. The picture below shows the recommended minimum
distances:
Dimensions in mm
300
1100
300
300
If the recommendations are not followed as described,
Circontrol will reject all responsibility and the warranty
will be void.

12
WallBox eNext Installation Manual
BOpening
Open the Wallbox using allen wrench.
2.5mm Allen wrench
Use the ratchet tool to open / close
in conditions that hinder access

13
CPositioning
Pierce the wall.
Drill bit M 6/8
Dimensions in mm
1100
255
230
115

14
WallBox eNext Installation Manual
DFixing
Place the unit on the previous pierced points and fix it with screws.

15
EWiring
A A
B
Cable
glands M32
• Use provided cable glands in order to mantain the IP protection
• The IEC-61851-1 ed 3 standard indicates each plug shall have protections. In case the
Charge Point has no protections inside, they shall be upstreams. It is recommended that
these protections be as follows:
° RCD: Residual current debice. Starndards: IEC 61008-1, IEC 61009-1,IEC 60947-2 and
IEC 62423
° Rated residual operating current not exceeding 30 mA.
› RCD(s) protecting connecting points shall be at least type A.
› The DC fault current shall be mesured by a RCD type B or a appropriate equipment
that ensures the disconnection of the supply in case of DC fault current above 6 mA
° MCB: Miniature circuit breaker. Standards: IEC 60898-1 or IEC 60947-2 or IEC 61009-1
› During first second shall be able to withstand 30 A
• The current of the power supply can be limited. In order to perform this adjustment please
refer to the instruction manual.
NOTE: In the following countries automatic reclosing of protection means is not allowed: DK,
UK, FR, CH.

16
WallBox eNext Installation Manual
L1
L2
L3
N
L
N
SINGLE-PHASE CHARGE POINT
• Connect to the 230VAC.
THREE-PHASE CHARGE POINT
• Connect to the 400VAC.
• If the Power Supply is Single-
Phase, connect L1 and N.
Do not forget to connect the ground cable to the ground terminal
Make sure all screws are securely tightened at 4 - 5 Nm
Terminal block maximum cross-section: 10mm2
S
Type of cable allowed by the terminal block: Copper
Cu
PE
PE
Protections Protections