Circontrol eHome Series Parts list manual

INSTRUCTION & INSTALLATION
MANUAL
MODELS:
CCL-eHOME T1C16
CCL-eHOME T1C32
CCL-eHOME T2C16
CCL-eHOME T2C32
WALLBOX eHOME

WALLBOX eHOME Instruction and Installation manual
This document is copyrighted by Circontrol, S.A. All rights are reserved.
Circontrol, S.A. reserves the right to make improvements to the products
described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted in
any form or by any means without the prior written permission of the original
manufacturer. Information provided in this manual is intended to be accurate
and reliable. However, the original manufacturer assumes no responsibility for
its use, or for any infringements upon the rights of third parties that may result
from its use.
All other product names or trademarks are properties of their respective
owners.
V1.3, Edition March 2018

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
1
CONTENTS
1INTRODUCTION................................................................................................................... 3
1.1 IMPORTANT SAFETY INFORMATION ........................................................................3
1.2 SHORT DESCRIPTION ................................................................................................ 4
2MAIN FEATURES................................................................................................................. 4
3FIRMWARE VERSION .........................................................................................................4
4OPERATING INSTRUCTIONS.............................................................................................5
4.1 CHARGING PROCEDURE ...........................................................................................5
4.2 STATUS LED BAR ERROR SEQUENCES...................................................................7
4.2.1 VENTILATION REQUIRED ERROR (D STATUS)*..............................................8
4.2.2 PILOT ERROR (E STATUS)*................................................................................8
4.2.3 PROXIMITY ERROR.............................................................................................9
4.2.4 NEGATIVE PWM VOLTAGE ERROR .................................................................. 9
4.2.5 MAXIMUM OUTPUT CURRENT MINIDIPS ERROR .........................................10
4.2.6 TEMPERATURE ERROR ...................................................................................10
5INSTALLATION GUIDELINES...........................................................................................11
5.1 PREFACE....................................................................................................................11
5.2 ELECTRICAL WIRING CONSIDERATIONS...............................................................12
5.3 SPACE REQUIREMENTS ..........................................................................................13
6PRODUCT DIMENSIONS...................................................................................................14
7FRONT PRODUCT VIEW...................................................................................................15
8INSIDE PRODUCT VIEW ...................................................................................................16
9INSTALLATION .................................................................................................................. 17
9.1 SUPPLIED MATERIAL................................................................................................17
9.2 OPENING THE UNIT...................................................................................................18
9.3 POWER SUPPLY LINE CABLE INSERTION..............................................................23
9.3.1 USING THE REAR CABLE INSERTION OPENING...........................................24
9.3.2 USING THE BOTTOM CABLE INSERTION OPENING .....................................25
9.4 WALL FIXATION PROCEDURE .................................................................................26
9.4.1 NEEDED MATERIAL...........................................................................................26
9.4.2 CONSIDERATIONS ............................................................................................26
9.4.3 INSTALLATION...................................................................................................27
9.5 ELECTRICAL INSTALLATION....................................................................................29
9.5.1 POWER SUPPLY LINE PROTECTIONS............................................................29

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
2
9.5.2 POWER SUPPLY LINE CONNECTION .............................................................30
9.6 CLOSING THE UNIT...................................................................................................31
10 CHECKING THE UNIT STATUS........................................................................................33
11 CURRENT LIMIT SELECTOR............................................................................................33
12 REMOTE CONTROL INPUT ..............................................................................................35
13 EHOME BEON (OPTIONAL).............................................................................................. 36
13.1 CONNNECTIONS OF EHOME BEON .........................................................................37
14 TECHNICAL DATA.............................................................................................................38
15 NOTES ................................................................................................................................ 39

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
3
1 INTRODUCTION
This manual contains all the necessary information for the safe use of the Wallbox
eHOME Electric Vehicle (EV) charging system and it will help you to get the best
performance results from the system.
This equipment incorporates the latest technology and offers the most advanced
service in the EV charging market.
1.1 IMPORTANT SAFETY INFORMATION
Read carefully all the instructions before starting, to
ensure the proper installation of the charging point.
The charging point is designed for installation in indoor and outdoor areas. Whatever
is the case, the unit must be installed safely with the adequate electrical protections.
•The charging point must not be installed in areas where there is a
potential risk of explosions.
•Do not install the charging point where falling objects may damage the
equipment.
•The wall surface where the charging point is placed must withstand the
mechanical forces.
•Do not use this unit for anything other than electric vehicle charging
modes which are expected in IEC 61851.
•Do not modify this unit. If modified, CIRCONTROL will reject all
responsibility and the warranty will be void.
•Comply strictly with electrical safety regulations.
•Do not make repairs or manipulations with the unit energised.
•Only trained and qualified personnel should have access to low-
voltage electrical parts inside the device.
•Check the installation annually by qualified technician.
•Remove from service any item that has a fault that could be dangerous
for users (broken plugs, caps that don’t close...).
•Use only Circontrol supplied spare parts.
•Do not use this product if the enclosure or the EV connector is broken,
cracked, open, or shows any other indication of damage.

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
4
1.2 SHORT DESCRIPTION
The Wallbox eHOME charging system is specially designed to be easily installed both
in outdoor and indoor private car parks, in order to charge all the EV brands of the
market in MODE 3 (according to European standard IEC 61851-1), by just connecting
either its tethered cable with a type 1 or type 2 connector.
2 MAIN FEATURES
•Remote control input: Allows to start/stop the EV charge by means of a
dedicated logic input.
•Plug & Play: It is possible to start charging by just plugging the Wallbox
eHOME connector into the car.
•Current limitation: By means of an on-board rotate dipswitch, the maximum
current delivered by the unit is setup.
•Status RGB LED bar: It shows the status of the unit when it is either available
or charging. Also some specific blinking error sequences are shown when there
is a faulty operation.
•Housing: Designed for outdoor and indoor operation.
3 FIRMWARE VERSION
When the unit is booting, the LED bar will show the firmware version in orange. The
first digit of the version will be shown as a certain number of blinking of the first LED, as
many times as the digit indicates, and the second digit will be displayed by the last LED
blinking accordingly to what the second digit indicates (i.e. for version 1.6, you will see
one blink at the first LED and six at the last LED).

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
5
* According to IEC 61851
4 OPERATING INSTRUCTIONS
4.1 CHARGING PROCEDURE
•The Wallbox eHOMEhas a status
LED bar. When it is in green colour, it
means that the unit is available and
ready to start a recharge (A status)*.
•To start a new recharge, plug the
Wallbox eHOME cable into your car.
1
2

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
6
* According to IEC 61851
* According to IEC 61851
•The status LED bar turns into blue.
•The WallBox eHOME starts the
charging process.
•While charging the EV, the LED
bar will be flashing continuously
(status C)*.
•When the EV is fully charged, the
charging process ends up and the
status LED bar stops flashing and
keeps fix in blue (B status)*.
•Then you can unplug the cable
from the EV.
3
4

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
7
* According to IEC 61851
4.2 STATUS LED BAR ERROR SEQUENCES
The Wallbox eHOME is capable to detect the following operating errors:
- Ventilation required error
- Pilot error
- Proximity error
- Negative PWM error
- Maximum output current MiniDips error
- Temperature error
Whatever the error case is, the unit will stop charging and technical assistance will be
required, except from the temperature error. In this last case, the unit starts charging
when the operating temperature is reached again.
In the following sections it will be explained how the Wallbox eHOME shows the above
mentioned errors and the actions taken by the unit.
•Once the cable is disconnected
from the EV, the LED status bar
turns back into green (A status)*.
•In this status, the unit is available
to start a new charging process,
whenever it is required.
5

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
8
* According to IEC 61851
* According to IEC 61851
4.2.1 VENTILATION REQUIRED ERROR (D STATUS)*
4.2.2 PILOT ERROR (E STATUS)*
•In some old EVs, this state means
that there are some gases coming
out from the batteries. So, an
external ventilation in the car park
might be required.
•If it was the case, the status LED
bar would turn into red and keep
flashing permanently.
•When the unit is connected to the
EV, a Pilot short-circuit to earth
may occur.
•Then, the status LED bar turns into
red and flashes in a sequence of
two blinks.

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
9
4.2.3 PROXIMITY ERROR
4.2.4 NEGATIVE PWM VOLTAGE ERROR
•When the unit is connected to the
EV, a Proximity short-circuit to earth
may occur.
•Then, the status LED bar turns into
red and flashes in a sequence of
three blinks.
•When the unit is connected to the
EV, the PWM signal, used to
communicate the unit with the EV,
can be negative.
•Then, the status LED bar turns into
red and flashes in a sequence of
four blinks.

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
10
4.2.5 MAXIMUM OUTPUT CURRENT MINIDIPS ERROR
4.2.6 TEMPERATURE ERROR
•If this on board current limit
selection is not setup according to
the hardware features, the unit
detects it and shows this error.
•In this case, the status LED bar
turns into red and flashes in a
sequence of five blinks.
•When the unit temperature is below
a certain value, it is detected by the
unit.
•In this situation, the status LED bar
turns into orange blinking.
•In the meantime, if the unit is
supplied with heater (optional), it
starts heating the inside
components until the operating
temperature is reached. Then the
unit starts charging again.

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
11
5 INSTALLATION GUIDELINES
5.1 PREFACE
THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT
SAFETY INFORMATION IN THIS DOCUMENT
ELECTRIC RISK!
Take precautions to make the electrical connection
inside the unit.
The unit must be disconnected from any power supply
during the commissioning.
ATTENTION!
Damage to the property can occur if appropiate
precautions are not taken.
This section provides the commissioning information for Wallbox eHOME series, where is
described the electrical components inside the charging station and a step-by-step
installation procedure.
Standards & directives
•Complies with IEC 61851, Electric vehicle conductive charging system (IEC
61851-1, IEC 61851-22).
•Complies with IEC 62196, Plugs, socket-outlets, vehicle couplers and vehicle
inlets (IEC 62196-1 and IEC 62196-2).
•Directives: 2014/35/UE, LVD; 2014/30/UE, EMC.

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
12
5.2 ELECTRICAL WIRING CONSIDERATIONS
Before starting with the wiring connection of the charging
station, you must take into consideration this section.
1. Charging point power supply
The charging point does not include elements for electrical protection.
The power supply line which comes from the distribution board to the charging point, must
meet the electrical safety standards, according to your country regulations. The minimum
safety required protections are as follows:
- RCD: Type A. IΔN=0.03A.
- MCB: Its gauge must be chosen depending on the maximum output current of the
charging point.
NOTE: For further information, please refer to the TECHNICAL DATA section.
2. Power supply - Line dimensioning
The dimensioning of the charging station power supply line must be checked by a qualified
electrician. Note that various factors such as the cable length between the distribution
board and the unit, its maximum output current or ambient temperature may have influence
of the selected cable.
So, it is important to select the appropriate cable cross-section in agreement with the local
regulations and the power supply cable type that it is used.
3. Charging point maximum output current
If the installed charging point power supply is less than the maximum output current of the
charge point, an adjustment to a lower nominal current must be performed using the on-
board rotate dipswitch.
NOTE: Please refer to the CURRENT LIMIT SELECTOR section in order to know how
to change this value.

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
13
5.3 SPACE REQUIREMENTS
When installing the unit it is necessary to respect some minimum distances for
maintenance and safety reasons.
The recommended value for the Aheight, it is minimum 600 mm, and maximum 1200 mm
Please comply accordingly to your country specifications.
Units specified in mm
300
300
300
A

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
14
6 PRODUCT DIMENSIONS
Units specified in mm

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
15
7 FRONT PRODUCT VIEW
.
1. Circontrol Logo
2. Front cover
3. Status RGB LED bar
4. OEM Logo
5. Frame
1
3
2
5
4

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
16
8 INSIDE PRODUCT VIEW
1. EV tethered cable
2. Output contactor
3. Main board
4. Current limit selector
5. Rear cover
6. RGB LEDs
7. Input terminals
8. Heater*
9. Power supply line
5
4
2
7
8
9
6
1
3
* Optional depending on the model

© CIRCONTROL
www.circontrol.com
Wallbox eHOME INSTRUCTION & INSTALLATION MANUAL
17
9 INSTALLATION
9.1 SUPPLIED MATERIAL
MATERIAL
Qty
Wallbox eHOME charging point
1
User manual
1
Cable gland M25x1.5
1