Cirris Easy-Touch Pro User manual

Easy-Touch Pro
Getting Started Guide
downloads.cirris.com
Software &
Documentation
To download software, the Easy-Touch
Pro User Manual, and other supporting
documentation scan the QR code here or on
the tester to visit downloads.cirris.com.

Cirris2
Getting Started
The Cirris Easy-Touch Pro combines superior flexibility with the simplicity of a
touchscreen user interface. The tester is controlled by the Easy-Wire software
running on an integrated PC under the Windows operating system. Test
programs and test results are stored in a database. By default, the database
is located on the unit’s hard drive. However, as an option, multiple testers can
share a single, networked database using the Cirris Server Software. See the
Cirris Server Software Install Guide for more information on this option.
This guide will help the new user set up the tester and become familiar with
its operation by working through the process of creating a test program and
testing a cable.
For complete operating instructions, see the Easy-Wire Help on the tester and
the Easy-Touch User Manual.
Symbols
Indicates that high voltage is produced by the tester and,
therefore, there is a risk of electric shock if safety warnings are
not followed.
Alerts users to a risk of personal injury or damage to the
equipment.
Indicates that a person using an electronically-controlled
medical device should not be permitted to perform high
voltage testing.
Safety
The Easy-Touch Pro tester is capable of performing high voltage Dielectric
Withstand (DW) and Insulation Resistance (IR) testing. By design and function,
the output of high voltage (hipot) testers presents a risk of electric shock. To
mitigate this risk, Easy-Touch testers limit current, high voltage energy and
high voltage charge to levels below thresholds that define Hazardous Live or
Dangerous in international standards IEC 61010-1 and EN 50191 respectively.
However, operators can still receive a painful or startling shock when using any
high voltage test equipment. Therefore, it’s necessary to protect workers from
exposure to high voltage.

Easy-Touch Pro Getting Started Guide 3
Protecting workers begins with training. Operators should understand:
●Basic electricity including the fact that electric current will take any avail-
able path to ground, including through a person.
●How to use the test equipment and how to recognize when high voltage
testing is being performed.
●Not to not touch the product or test fixture hardware during high voltage
testing.
A safe test station is an essential complement to training:
●Use a non-conductive work surface to avoid creating an unintended elec-
trical path between high voltage and workers.
●Verify that the power outlet provides a properly wired, low impedance
earth ground. The connection to earth ground is integral to the power
cord supplied with the tester.
●Do not allow untrained workers to use high voltage test equipment.
●Isolate high voltage testing from untrained employees and post high volt-
age warning signs at the test station.
Medical Safety Warning
An individual using a cardiac pacemaker, an insulin pump, or any electronically-
controlled medical device should NOT perform high voltage testing.
Intended Use
Cirris Easy-Touch Pro testers are designed for electrical testing and are
intended to be used indoors, in a dry environment, at a temperature of 50-104
degrees Fahrenheit (10-40 degrees Celsius). High voltage Insulation Resistance
measurements degrade at over 70% relative humidity.
No User-Serviceable Parts
The tester includes no user-serviceable parts. Attempting repairs or altering
the tester in any way voids the warranty and may lead to an unsafe condition.
Contact Cirris Technical Support for assistance if needed.

Cirris4
Unpacking
☐Easy-Touch Pro Tester
Easy Touch PRO ™High Voltage CableTester
☐Power Cord
☐Probe
☐Certificate of Calibration
You may have also received:
■ Expansion Scanners
■ Cirris Adapters
■ Tilt Stand
■ Performance Verification Kit
The package in which the tester shipped included:
Hardware Setup
The tester includes 128 test points in the base enclosure. It can be expanded
to a maximum of 1024 test points using 128-point Expansion Scanners. See the
Easy-Touch Pro User Manual for Expansion Scanner installation instructions.
After installing any included expansion scanners:
1. Connect the Probe.
2. Connect the Power Cord and plug the power cord into a grounded outlet
(surge protector recommended).
3. Press the power switch to turn on the tester.
Probe
Status
Indicator
Digital
I/O
DP
AC Input
50-60 Hz
100-240 V~
4-2 A
Easy Touch Pro
Made in U.S.A.

Easy-Touch Pro Getting Started Guide 5
Startup
1. After power up, the Easy-Wire software
will open to the User Login window. Select
Master Login from the drop down list. Do
not enter a password. Click OK
Passwords and new users can be created
from the Main Menu > Utilities > Setup
Security. See the Easy-Wire Help.
2. The tester performs a series of self-tests during initialization. These tests
ensure that the hardware and software are working properly. When the
self-test passes, the Main Menu will open with a Ready status indicator.
3. The software license purchased with a new Easy-Touch Pro tester includes
software upgrades for a period of one year. The Main Menu shows a
Licensed status. Details can be accessed by clicking/tapping View License.
4. To turn o the tester, click/tap Exit > Power O.

Cirris6
Changing the Interface Language
The language used in the Easy-Wire interface can be changed to one of the
available options.
1. From the Main Menu > Utilities > Setup System Options.
2. Under the Software Settings tab, select Change.
3. Select a language from the list of options and click OK.
4. Click OK on the Setup System Options window to return to the Main
Menu.
The Easy-Wire Help
The Easy-Wire software includes a contextual Help system accessed by clicking/
tapping the Help button available on most Easy-Wire windows. The Help can be
browsed using its Table of Contents or searched by keywords.

Easy-Touch Pro Getting Started Guide 7
Fixturing
Easy-Touch Pro testers use interchangeable adapters as the interface for
connecting the tester to the Device Under Test (DUT). Standard adapters are
available with a wide variety of connector types (a complete list can be found on
the Cirris web site). However, if the DUT includes connectors that have no direct
adapter mates, test cables can be used to connect the connector on a standard
Cirris adapter to the DUT connector. Your Cirris sales representative can also
provide pricing for custom adapters.
Adapters are available in three sizes. Single-high adapters plug into one
receptacle on the tester (e.g. J1). Double-high adapters plug into two vertically-
adjacent receptacles (e.g. J1 & J2). Quad-high adapters plug into all four
receptacles on the tester base or on an expansion scanner.
Adapter Installation
1. Push the slidelocks to the outward
positions.
2. Set an adapter in one or more of
the J1-J4 slots. Align the adapter
properly to avoid damage and push
it to the left (toward the tester’s
screen) with steady, even pressure.
3. The adapter is fully seated when the
slidelocks can be moved inward to
hold the adapter in place.
Adapter Maintenance
●Premium gold plating provides 500 or more mating cycles. A very low
contact resistance of 10mΩ will likely be maintained during this time. Con-
tact resistance gradually increases with additional cycles, therefore, appli-
cation requirements will determine when adapters should be replaced.
●Always use slidelocks to reduce the stress on the adapter pins and on the
tester’s receptacles increasing the lifespan of both.
●Visually inspect right-angle adapter pins before each use. Bent pins can
damage the tester’s receptacles.
●Never straighten pins using serrated pliers as this produces a saw-like
profile that will damage the tester receptacles.
●Store adapters properly to reduce the possibility of damage. Cirris oers
ARAC-SS and ARAC-SD adapter trays for this purpose.
J2
J1
J4
J3
3
3
2
1

Cirris8
Create a New Test Program
Before a device can be tested, a test program must be created. This is most
often accomplished by using the tester’s capability to “learn” a sample product.
Once a test program has been created, it can be saved and then loaded as
needed to test subsequent batches of the same product.
To create a test program using the Learn feature:
1. Install the appropriate adapters.
2. Connect the sample product to the tester.
3. From the Main Menu > Create Test.
4. On the window that opens, select
Learn Signature Test Program.
5. Set the learn parameters.
●Set the maximum acceptable
Connection Resistance and
the minimum acceptable
LV (low voltage) Insulation
Resistance.
●Check High Voltage Testing
ON to include it in the
resulting program (high
voltage is not used during the
learn process). Click Set High
Voltage Parameters to edit
the test criteria.
●Check any components included in the product.
●Click/tap Learn Attached Device to begin the learn process.

Easy-Touch Pro Getting Started Guide 9
Verify and Edit the Test Program
When the learn process is complete, the test program will open in the
Test Program Editor to the Define Instructions tab. Verify that the learned
instructions match the product’s documentation. Click/tap Help on any screen
for guidance.
Define Instructions Tab
●To edit an instruction, select it > Edit Instruction.
●To delete an instruction, select it > Delete Instruction.
●To add an instruction, select the appropriate instruction type from the drop
down list > Add Instruction and complete the form that opens.
Set Test Defaults Tab
●To edit the Connection Resistance and/or LV Insulation Resistance, click/
tap Set Low Voltage
●Select the Start Condition and the Test Method.
View Nets Tab
View Nets, Nets Joined by Components, and Single Points. Turn High Voltage
o for specified nets and customize High Voltage parameters by net, if required.
Label Points Tab
The location of the adapters (J1, J2, J3 etc.) and the positions within their
connectors (001, 002, 003 etc.) are used to identify test points, for example J1-
001. Product-specific nomenclature can be used instead by adding point Labels.

Cirris10
Save the Test Program
After verifying that the test program is accurate, click/tap Save to assign the test
program a name and to save the program. A program revision and comment
can be added whenever saving a new or revised version.
Test
To load a test program for a test session, from the Main Menu, click/tap a test
program name to highlight it > Test.
1. Depending on the Start Condition, either attach a cable to start the test
automatically or attach a cable and click/tap Start.
2. Low voltage testing is performed first and may take less than a second
to complete. If the low voltage portion of the test fails, the test will
terminate. If the low voltage portion of the test passes, and the program
includes high voltage (Hipot) testing, the tester will be ready to continue.
Depending on the Automatic Hipot setting, the tester will either
automatically proceed with the high voltage testing or it will pause and
wait for the operator to click/tap Hipot.
3. If an intermittents test was programmed, it will begin after the initial test
cycle passes. Flex the cable to check for intermittent errors. The test will
end depending on the Test Method settings.

Easy-Touch Pro Getting Started Guide 11
4. If the test passed, the header will turn green and display Good. If the test
failed, the header will turn red and display Bad and the error details will
appear in the test window. For more information on errors, refer to the
Easy-Touch Pro User Manual.
5. When the test is complete, disconnect the DUT from the tester. The test
screen will reset and be ready for the operator to connect another cable,
or press Done to return to the Main Menu. If an auto-print report was
included in the program, it will print when the DUT is disconnected from
the tester.
Calibration
New Cirris testers ship with a Certificate of Calibration valid for one year. Cirris
recommends that the calibration be validated annually at a minimum thereafter.
The validation can be performed by Cirris or by the end user or a calibration
service provider using an Easy-Touch Performance Verification Kit. Contact your
Cirris sales representative for more information.
Documentation
In addition to this Getting Started Guide, there are several resources that pro-
vide important information about the test system and its operation. The Easy-
Wire Help is installed with the software. Software, manuals, and other documen-
tation can be downloaded from the Cirris web site at downloads.cirris.com or
by scanning the QR code on the tester.
●Easy-Touch Pro User Manual - Provides important additional information
about building test fixtures and developing test programs.
●Easy-Wire Help - The Easy-Wire software includes an integrated Help
system that provides contextual assistance accessible throughout the
application.
●Cirris Server Software Install Guide - Describes the Cirris Server Software
installation and how to connect a test station to the server.

Help / Support
For assistance with your Cirris tester:
●Visit www.cirris.com/learning-center to read articles on Cirris products and
other testing subjects.
●Visit the Cirris YouTube channel to find instructive videos.
●In the United States, contact our technical support team at techsupport@
cirris.com or by phone at 801-973-4600, ext. 666 (or ask for Tech Support).
●Outside the United States, visit the contact page of the Cirris web site at
cirris.com to find your local representative.
Warranty
Cirris Inc. warrants new products manufactured by Cirris Inc. to be free from de-
fects in material and workmanship for a period of twelve months. Products not
manufactured by Cirris Inc. are warranted by their manufacturer. Cirris Inc. at its
option will repair or replace faulty goods and is not responsible for any conse-
quential loss incurred due to faulty goods. This warranty does not cover normal
wear, misuse or consumable items. The warranty does not include modifications
or damages due to abuse by the user.
NO WARRANTY AGAINST INFRINGEMENT: Cirris Inc. makes no warranty what-
soever that the goods are delivered free of any rightful claim of any third person
for infringement of patent.
Cirris, Inc.
401 North 5600 West
Salt Lake City, UT 84116
USA
1-801-973-4600
www.cirris.com 2021.4.2