Cisco TelePresence MX700 User manual

78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved. http://www.cisco.com/go/mx-docs
Installation guide
for Cisco TelePresence MX700 Dual Camera
mounted on the wall

78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 2
This guide covers the MX700 with dual camera, mounted on the wall.
Safety information
Due to the size and mass of this product it is important that
the wall mounted system is safely installed according to
these installation instructions.
The wall and mounting hardware must be able to safely
support the product.
The wall mounted system must be installed by qualified
personnel, in accordance with state and local building
regulations.
Manpower
We recommend three
people working together
to mount this system.
Follow local regulations.
Dimensions
Height: 1071 mm / 42.2 in.
Width: 2517 mm / 99.1in.
Depth: 148 mm / 5.9in.
Weight: 164kg / 362lb
Room setup
Explore the Cisco Project Workplace to find
inspiration and guidelines when preparing your
office or meeting room for video conferencing,
http://www.cisco.com/go/projectworkplace
User documentation
The user documentation for this product,
including compliance and safety information,
can be found on the Cisco web site,
http://www.cisco.com/go/mx-docs
EMC Class A declaration
WARNING: This is a class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
声
明
此为A级产品，在生活环境中，该产品可能会造成无线电干扰。在这种
情况下，可能需要用户对其干扰采取切实可行的措施。
WARNING: This is a class A product. In a domestic environment
this product may cause radio interference in which case the user
may be required to take adequate measures.

78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 3
Packaging
1Open the plastic snap locks and remove the
side walls.
Lift off box L/M. Lay box A flat on the floor
and remove the lid.
2
L/M
A
D
Boxes are labeled A to M. This
guide refers to the labels.
A M
...
B+E-G Shows which boxes are inside.
Tools and screws are in this box.
Screws
Countersunk, Allen key, 4 mm
M6x90
M6x35
M6x12
Pan, Allen key, 4 mm
M6x12
Pan, Allen key, 2.5mm
M4x8
Pan, Torx T20
PT4x10

1Assemble lower frame
A, B
78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 4
Six screws from the back
and two from the top.
8 × M6x12
(countersunk)

2Fasten center bracket
B
78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 5
2 × M6x12
(pan)

3Mount left wall bracket
A
78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 6
Check that the wall bracket is level and mark the required
screw hole positions on the wall. Use at least four screws
when fastening the wall bracket. The wall bracket can be
fastened through any of the horizontal slots.
Fasten the wall bracket in a secure manner ensuring that
the wall’s structure is sufficient to support the system load
(screws/mounting hardware not provided; not shown in
illustration). The lower edge of the
picture on screen will
be at this height.

4Mount right wall bracket
A
78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 7
You may use the lower frame to check that the
two brackets are level.
Follow the mounting instructions in the same way
as you did for the left wall bracket.
254 mm
(10 in.)

5Mount spacers and top wall brackets
A
78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 8
Snap the top bracket onto the
spacers.
Fasten the top bracket in a secure
manner ensuring that the wall’s
structure is sufficient to support
the system (screws/mounting
hardware not provided; not shown
in illustration).
2
1
Mount spacers onto the wall
brackets.
Fasten each spacer with two
screws (not provided; not shown
in illustration).

6Fasten lower frame
78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 9
M6x90
M6x35
M6x12
M6x12 (pan)
M4x8 (pan)
4 × M6x12 (pan)

7Fasten clamps on monitors
A, D
78-100279-01 B0 | 2014 JUNE | © 2014 Cisco Systems, Inc. All rights reserved.
Installation guide for Cisco TelePresence MX700 Dual camera - Wall mount
Page 10
While the monitors are still in the package, mount
the clamps on the rear side of the monitors.
Loosen the four pre-mounted screws on the
clamp, slide the clamp in place, and tighten the
screws.