Cisco TANDBERG Quick Set C20 Instruction Manual

D1451302
(11983304 as printer firendly version June 2010) 1
Installing the TANDBERG Quick Set C20
Contents of this box
• TANDBERGC20Codec
• TANDBERGPrecisionHD1080p12×Camera/
TANDBERGPrecisionHD1080p4×Camera
• TANDBERGPerformanceMic20Microphone
• TANDBERGRemoteControlTRCV
• Accessories:
• 3×HDMIcableforscreenandcamera
connectivity
• EthernetcableforLAN
• VGAtoDVI-AcableforPCconnectivity
• Cameracable
• Powersupply
• Cameramountingbracket
User Guides
TheuserdocumentationforTANDBERGproductsis
foundontheTANDBERGwebsite.
Goto:http://www.tandberg.com/docs
PrecisionHD1080p4×
PrecisionHD1080p12×

D1451302
(11983304 as printer firendly version June 2010) 2
Installing the TANDBERG Quick Set C20
Thecameramountingbracket
shouldbemountedsothatthe
cameragetspositionedontop
ofyourmonitortoenhancethe
perceivedeyecontact.
PrecisionHD1080p12×Camera
shownwiththelenshoodmounted.
PrecisionHD1080p4×Camera
requiresnolenshood.
About the PrecisionHD 1080p 12× camera
ThePrecisionHD1080p12×cameracomeswithalenshood.Theuseof
thislenshoodwillpreventstraylightfromdisturbingyourvideoexperience.

D1451302
(11983304 as printer firendly version June 2010) 3
Installing the TANDBERG Quick Set C20
Caution!
Inordertobeabletouse
thesystemforvideocalls,all
orangecoloredsocketsmust
beconnected.
Makesureallunitsare
switchedoffwhenever
connectingordisconnecting
devices!
Connecting the PrecisionHD 1080p 12× camera

D1451302
(11983304 as printer firendly version June 2010) 4
Installing the TANDBERG Quick Set C20
Caution!
Inordertobeabletouse
thesystemforvideocalls,all
orangecoloredsocketsmust
beconnected.
Makesureallunitsare
switchedoffwhenever
connectingordisconnecting
devices!
Connecting the PrecisionHD 1080p 4× camera

D1451302
(11983304 as printer firendly version June 2010) 5
Installing the TANDBERG Quick Set C20
Waking up the system
Ifthereisnomenuonthescreen,pressHome( )ontheremotecontrolto
produceit.
Do as follows:
1. Makesurethemonitorhasbeenturnedon.
2. Makesuretheremotecontrolhasitsbatteriesinstalled.
3. Makesurethecodechasbeenturnedon.
4. Ifthesystemhasjustbeenturnedon,giveitacoupleofminutestostartup.
1
4If you need to set a static IP address
Go to IP Settings to set static IP addresses:
1. NavigatetoSettings > Advanced > IP settings.
2. SetIP Assignment toStatic.Presstheleftarrowkeytogobackonestep
3. Enterthe IP Address,Subnet Mask andGatewayaddressintheaddressfields.
4. PressOKtosavethechanges,orCanceltoleavewithoutsaving.
5. PressHome ( )toexit.
Verifying IP address settings
GotoSystem InformationtoverifytheIPaddress:
1. NavigatetoSettings > System Information
2. WhentheIPaddressisautomaticallyassignedfromaDHCPserver,thenetwork
IPaddressofthecodecisshownontheSystem Information page.
3. PressHome ( )toexit.
2
3Password protection of the administrator settings
WhenyouaccesstheAdministratorsettingsyoumaybeaskedtoenterapassword.
Theadministratorpasswordisblankbydefault.PressOKtoproceed.Oncethe
initialconfigurationshavebeenset,werecommendthatyoudefineanadministrator
password.
Setting static IP address
Using DHCP

D1451302
(11983304 as printer firendly version June 2010) 6
Installing the TANDBERG Quick Set C20
6Verify your settings
WestronglyrecommendthatyouverifythesettingsbyinspectingtheSystem
Informationlist.
YoudothisbyaccessingtheSystemInformationinthesamewayasyoudidwhen
youverifiedyouIPaddresssetting.
Go to System Information to verify the settings:
1. NavigatetoSettings > System Information
2. Verifythepreviousconfigurations.Forexample,ifyousuccessfullyregistered
toaSIPservertheStatuswillshowRegistered.Iftheregistrationfailedthe
Statuswillshow Not registered.
3. PressHome( )toexit.
5Add the system to the network
Yourserviceprovidershouldhaveprovidedyouwiththeinformationyouneed
togeton-line.
ForH.323typeofcommunication,thiswillincludesuchthingsassystem
name,H.323alias,gatekeeperaddress,etc.ForSIPtypeofcommunication,
similartypeofinformationwillbesupplied.
FornetworksadministratedthroughTMS(TANDBERGManagementSuite),
yourTMSadministratorwillbeabletoassistyouwhenconfiguring.
The H.323 and SIP settings are configured from the Advanced
configurations menu:
1. NavigatetoSettings > Advanced > Advanced Configuration andselect
H323 or SIP
2. Expandtheitemsinneedofmodificationandentertheinformation
suppliedbyyourserviceprovider.
7Set the time and date
Verifythedateandtimetoseeifthetimezonesettingsneedtobeadjusted.
Thedateandtimeislocatedintheupperrightcorneronscreen.
Go to the Time settings to set the date and time:
1. NavigatetoSettings > Date and time
• IfyouconfigureSet date and time toAuto:
• SelecttheGMTtimezonefromthelistandaselectformatforthe
dateandtime.
• IfyouconfigureSet date and time toManual:
• Setthedate,month,year,timeandselectaformatforthedateand
time.
2. PressSavetosavethechanges,orCanceltoleavewithoutsaving.
8Set the administrator settings menu password
Bydefaulttheadministratorpasswordisblank.
NOTE!Itishighlyrecommendedtodefineapasswordtoaccesstheadministrator
settingsmenus.Changingthesesettingsmayaffectthebehaviorofthesystemand
shouldbedonebythesystemadministrator.
NOTE!Whenyoudefineorchangetheadministratorpasswordmakesureyousavea
copyofthepasswordinasafeplace.
Define the password:
1. Navigateto Settings > Advanced > Change password
2. Ontheremotecontrol,pressthe#keytotogglebetweenloweroruppercase
charactersandnumbers:abc/ABC/123
3. Enterthepassword.Thepasswordyouenterishidden,aseachcharacterisreplaced
withastar(*).
4. PressSavetosavethechanges,orCanceltoleavewithoutsaving.
5. PressHome ( )toexit.