Cleveland PDM-2 User manual

Cleveland
™
Project ________________________________
Item __________________________________
Quantity_______________________________
FCSI Section ____________________________
Approval _______________________________
Date __________________________________
1333 East 179 St.,
Cleveland, Ohio,U.S.A. 44110
Tel: [phone]
Fax: [phone]
Web Site:www.ClevelandRange.com
Email: [e-mail]
PRESSURE STEAMERS
Cleveland Standard Features
n5psi Operating Pressure in cooking compartments
n Mechanical interlock prevents unlatching door while compartment
is pressurized
nTimers, one per compartment, are mechanical style with
audible signal
n Thermostatic Trap vents cooking compartment automatically
nSteam Inlet Valves and Exhaust Valves interlocked for
synchronous action
n8psi Compartment Safety Valve
nCapacity per compartment for eight, 12” x 20” x 2 1/2” deep
Cafeteria Pans, or four, 18” x 26” Bun Pans
nHeavy Duty, free floating, cast aluminum compartment
doors
nCompartment Door Hinges have adjustable hinge pins and
self-lubricating bushings
nDoor Gasket replaceable without tools
nPressure Gauge for compartment Operating Pressure
nCompartment Slide Racks are removable without tools, for
easy cleaning
nType430 Stainless Steel: external enclosure, Table Top and
eight gage plate cooking compartments
n6” Stainless Steel Legs with level adjustment and flanged
feet
nMoisture Separator for incoming steam
nPressure Reducing Valve for 12 to 50 psi steam supply
pressure
Options & Accessories
pAutomatic Steam Inlet and Exhaust Operation (AT-2):
includes 60 minute Automatic Timers and Manual Bypass
pSecond Pressure Reducing Valve for 50 to 120 psi steam
supply pressure (PRV)
pStainless Steel base Frame (FSS)
pSpecial Compartment Slide Racks
p12” x 20” Cafeteria Pans 1”, 2 1/2”, 4” or 6” deep
pIntermediate Pull-Out Shelf (POS)
pSpray Head with flexible Hose (SH)
pWater Filters
sClean, non toxic, uncontaminated steam is required for all
“Direct Steam” steamers
Shall be _____ Compartments, CLEVELAND, Pressure Steamer, Model
PDM-_____, for Direct Steam Operation, _____ volts single phase.
Each Cooking Compartment equipped with: 60 Minute Timer;
PressureSafety Valve; Heavy-duty, free floating Door with Safety
Interlock; and synchronous operating Steam Inlet and Exhaust/Drain
Valves. Modular Cabinet Base with Hinged Doors. Pressure Reducing
Valve and Moisture Separator.
ShortFormSpecifications
SECT. VI PAGE 7
0707
PRESSURE STEAMERS
2OR 3 COMPARTMENTS
DIRECT STEAM
36” WIDE CABINET BASE
MODELS:2Compartments 3 Compartments
cPDM-2 cPDM-3

The Floor Drain must be
located outside the con-
fines of the equipment.
11/2” IPS common drain.
Do not connect other
units to this drain.
Do not use PVC pipe for
drain.
(NOT TOSCALE)
SECT.VI PAGE 8
0707
Litho in U.S.A.
•Each compartment has capacity for:
Eight, 12˝ x 20˝ x 21⁄2˝ Cafeteria Pans or
Six, 12˝ x 20˝ x 4˝ Cafeteria Pans or
Four, 12˝ x 20˝ x 6˝ Cafeteria Pans or
Four, 18˝ x 26˝ Bun Pans
•Many regional, state and local codes exist and it is
the responsibility of the owner and installer to com-
ply with those codes.
•Cleveland Range equipment is built to comply with
applicable standards for manufacturers. Included
among those approval agencies are: UL, ULC, NSF,
and CSA.
WATER QUALITY REQUIREMENT
The recommended minimum water quality standards
whether untreated or pre-treated, based upon 10 hours
of use per day,and a Daily Blowdown, are as follows:
TOTAL DISSOLVED SOLIDS less than 60 parts per million
TOTAL ALKALINITY less than 20 parts per million
SILICA less than 13 parts per million
pH FACTOR greater than 7.5
CHLORINE less than 30 parts per million
Consult a local water treatment specialist for an on site
water analysis for recommendations concerning steam
generator feed water treatment (if required), in order to
remove or reduce harmful concentrations of minerals.
The use of highly mineralized water will mean that more
frequent servicing of the steam generator will be
necessary. The fact that a water supply is potable is not
proof that it will be suitable for the generator.
Cleveland Range reserves right of design improvement or modification, as warranted.
Right - 3”, Left - 3”, Rear - 3”
(12” on control side if
adjoining wall or equipment
is over 30” high for service
access)
Contact factory for
variances to clearances.