Clevertronics CLP LIFELIGHT CLIFE Series Maintenance and service guide

1941951
V1.6
5 October 2021
UK Instruction Sheet Template – V1.1 – Updated: 20/11/2020
Zoneworks and DATA Monitored Options
Lifelights with part numbers CLIFE-ZW, CLIFE-DATA are fitted with Zoneworks communications modules
(nodes). These fittings are monitored using either Powerline Carrier Technology that utilises the power
cable to provide data communication or a dedicated data cable to/from data router installed on a dedicated
data trunk connected to a central Server (can also be connected via Ethernet/Internet/Fibre). Zoneworks
software on the server is used to monitor, coordinate testing and collate test data from each Lifelight.
Zoneworks Lifelights can be commissioned by a single push of the test switch or scanning of the supplied
barcode. The LED Test Switch indicator provides a multifunction indication of the status of the Lifelight
during testing and normal operation:
State LED Operation
Commissioned LED on Solid (Green)
Un-commissioned LED flashes at 0.5Hz (0.5s Green, 0.5s Yellow)
Emergency Light Test In Progress LED flashes at 3s On (Yellow) & 0.5s Off
In the case of the DATA version a 2-way “figure 8” cable and terminal block facilitates the connection to
the DATA network via a multi-drop bus (daisy chain connection). For further information of installation of
a Zoneworks system, please refer to the Zoneworks Users Guide and Commissioning Guide (incl. DATA
version)
DALI EM Option
Lifelights with part numbers CLIFE-DALI are fitted with DALI modules (nodes) that facilitate connection
and integration to 3rd Party Lighting Control Systems. Before installing the CLIFE-DALI please confirm
that the Lighting Control System has the capability to monitor DALI Emergency Luminaires. The CLIFE-
DALI will be addressed and configured into the control system by the Lighting Control System
Commissioning Technicians and not Clevertronics.
State
LED Operation
Commissioned/ Un-commissioned LED on Solid (Green)
Emergency Light Test in progress LED flashes at 1s On (Yellow) & 1s Off
“IDENTIFY COMMAND” Lamp and Status LED Flash for 30 seconds
A 2-way “figure 8” cable and terminal block facilitates the connection to the DALI network OR a 5/6way
“structured wiring system” lead and plug facilitating the power and DALI connection. DALI connections
are marked as Da Da.
Clevertest and Clevertest Plus
Refer to the supplementary operation guide supplied with the Product.
After Power ON, the Status LED on a Clevertest Plus enabled fitting will display a rapid Green or Red
flashing for a period up to 2 minutes.
CLP™ LIFELIGHT Recessed Emergency
Luminaire
Installation & Maintenance Instruction Leaflet
NOTE: Standard product codes with this symbol
are enabled with Clevertest Plus capability. Please refer to the
operation guide supplied with the product for details.
Australia (Head Office)
Website: www.clevertronics.com.au
Email: [e-mail]
Phone: [phone]
Fax: [phone]
IP20
UK OFFICE
Website: www.clevertronics.co.uk
Email: [e-mail]
362 Stockley Close
West Drayton UB7 9BL
Phone: [phone]
Models:
CLIFE-xx
Testing Options:
Manual Test
xx = Blank
Zoneworks
xx = ZW
Z/W DATA
xx = DATA
DALI Comp.
xx = DALI
Spare Parts:
1100925
LifeLight Head Assembly, Round, LT, 1LED
1550092
BATT:CLP 3.2V 3200mAh 260mm lead,no BRKT, With SLEEVE
CLIFE-CKIT-500
CLIFE-CKIT-500,Lifelight, Control Only, CLP Lithium
Important:
It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,
ensure that the electricity supply has been switched off and isolated. Installation must be carried out in
accordance with the relevant British Standards.

1941951
V1.6
5 October 2021
UK Instruction Sheet Template – V1.1 – Updated: 20/11/2020
Installation:
This CLIFE Recessed Non-Maintained Emergency Luminaire can be installed on PLASTER or T-BAR
ceilings or used to replace an existing unit.
•First plan the assembly layout ensuring the battery is kept away from any heat source.
•Refer Images and Dimensions below for the Cut-out Hole and other dimensions.
•Use the Spring Clip Mount to mount the Head to the ceiling.
•Please ensure the control pack and battery is suspended above the ceiling. If the control pack and
battery are to be mounted or placed on top of the ceiling, then please ensure the ceiling is capable
of supporting these elements and in compliance with the relevant regulations with respect to
mounting above/on the ceiling.
•This luminaire contains non-user replaceable light source and battery.
•If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by
the manufacturer or his service agent or a similar qualified person to avoid a hazard.
•Terminal block not included. Installation may require advice from a qualified person.
•Recommended specifications of terminal block for connecting leads:
−Type of Terminal: Screw Terminal
−Number of Terminals: 2-Pin
−Rated Voltage: 250 V
−Rated Connecting Capacity: 10A
•If the CTP capabilities are activated, please affix the CTP status label to a visible surface and Four
Segment Marking on the product will include an ‘’F’’ in third segment block.
Networking:
When installing the product on a monitored network, (ZONEWORKS, DATA, DALI) simply insert the
relevant Smart Node PCA.
Images and Dimensions:
Head depth: 40mm including connector
Head Diameter: 95mm diameter
Cut-out Hole: 85mm diameter
Adaptor Ring: 145mm diameter, suits 125mm hole
Control gear: 232mm (L) x 51mm (W) x 42mm
Battery pack: 165mm (L) x 38mm (W) x 35mm (H)
145mm Adaptor Ring
Note:
This luminaire (with reinforced insulation between control/LED terminal and AC supply) contains non-
user replaceable light source and battery - to be replaced (if required, refer installation instructions for
battery replacement) by Clevertronics service personnel/agents or a registered electrician.
Battery Replacement:
1. Prior to any work, isolate the power to the luminaire that requires battery replacement.
2. Remove the cord anchor securing battery cable by removing screw under driver.
3. Remove the Battery Connector from the Emergency Driver.
4. Replace battery, reconnect battery connector to Emergency Driver.
5. Carefully reinstall the cord anchor ensuring the lamp cable and battery cable are not pinched or
damaged.
Testing Procedure:
When the unit is connected to the un-switched active, it must be allowed to charge the battery for at
least 24 hours. The emergency lamp only illuminates during a power fail. Conduct the following tests:
•The emergency lamp must illuminate for at least 180 min after disconnection from the mains. If the
unit fails to illuminate for the requisite time, remedial action must be taken to repair the situation
and once completed, the unit must pass a subsequent test.
•Press and hold Test Button or switch Off Mains Supply, check that the emergency lamp is On.
•Release the Test Button or Switch On Mains Supply, check that the emergency lamp is Off (Non-
maintained operation).
Below are a list of common problems and their possible causes:
Fault: The Green LED indicator is not illuminated.
Check: A.C. is connected and is turned on.
Battery is connected.
Test Switch for damage.
Fault: Lamp does not illuminate in emergency mode.
Check: A.C. is connected.
Lamp is correctly inserted.
Battery is connected
Fault: Lamp illuminates in emergency mode, but only stays on for a short period.
Check: Battery has been allowed to charge for at least 24 hours.
Battery for damage.
Caution:
On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during
construction. As a result, any Exit & Emergency Units, on these circuits, will have their batteries
discharged or “cycled”. The Li-ion battery in the Exit & Emergency Unit has been selected to give
excellent long life performance in a controlled IEC 60598-2-22 testing environment. Excessive battery
cycling will reduce through-life performance and may lead to premature battery failure. Battery warranty
claims, as a result of such abuse, are specifically EXCLUDED from Clevertronics warranty terms.
Warranty:
For Product Warranty information and Terms and Conditions of Sales please refer to our website
https://clevertronics.co.uk/product-warranty-statement/