
Mounting Guide
10
Clutch Repositioning
Change the position of the Free-SpoolT-handle according to the following steps.
1. Loosen and release the bolts on the brake rear cover for separating the brake rear cover away.
2. Loosen and release the bolts on the gearbox away for separating the gear box away.
3. Rotate the gearbox by a proper angle increments mentioned on the below chart to the required
position.
4. Re-assembly the gearbox and rear brake cover.
Mounting Configurations
The payout direction for wire rope/synthetic rope or the correct methods for mounting the winch
vary according to different winch model.Do wind the rope from the bottom of the drum. At any
condition,do not position the load direction away from the mounting base plate.
Foot Down Mounting Position Foot Forward Mounting Position
Winch Model
Seal Gen2 9.5i/9.5si/9.5rsi
Seal Gen2 12.5/12.5s/12.5rs
Seal Gen2 16.5/16.5s/16.5rs
Seal Gen2 Series Winch
Limited Lifetime Warranty for Mechanical Components
Limited Three(3) Year Warranty for Electrical Components
Seal Gen2 Series WARRANTY
Comeup Industries Inc. (COMEUP) warrants to the original purchaser that the mechanical
components of the COMEUP Automotive Winch will be free of defects in material and workmanship for
the lifetime of the winch and the electrical components will be free of defects in material and
workmanship for a period of three (3) years for Seal Gen2 winches from the original date of purchase.
All COMEUP mounting kits and other accessories carry a one (1) year limited warranty against defects
in material workmanship.
This warranty applies only to the original purchaser of the winch. To obtain any warranty service,
the purchaser under this Limited Warranty is requested to advise COMEUP or its authorized
distributors on any claim. The purchaser must provide a copy of the purchase receipt bearing the
winch serial number, date of purchase, owners name, email or Tel & Fax, address and purchaser
vehicle details. Any products that COMEUP determines to be accountable for defective will be
repaired or replaced or refund at COMEUP sole discretion without charge to buyer upon buyer’s
compliance with these procedures. In the event of repair or replace, purchaser must send the
defective winch or part, with freight prepaid, to COMEUP or its authorized distributor. And COMEUP
will send the serviced product back to purchaser on COMEUP’s cost. This warranty does not cover the
removal or reinstallation of the winch.
COMEUP takes the responsibility for COMEUP winch parts and components to be free from
defects in materials and workmanship, but the following portions are hereby excluded and disclaimed.
COMEUP or its authorized distributors may make reasonable charges for parts and labour for repairs
or resumption in the following portions not covered by this limited warranty.
(1).All warranties of wire rope and synthetic rope assemblies after initial use
(2). All warranties of fitness for a particular purpose
(3).All warranties of the product’s finish
(4).All warranties of merchantability
The limited warranty does not cover any failure that results from improper installation/operation,
third party part substitution, purchaser’s alteration or modification on COMEUP winch. This warranty is
void when COMEUP serial number plate is removed or defaced.
COMEUP’s liability to the purchaser under the winch purchases for any loss or damage howsoever
and whatsoever arising shall not exceed the price of the initial winch purchase receipt. COMEUP shall
not in any event be liable to the purchaser for any consequential and/or indirect loss or damage
whether for loss or for profit or otherwise, costs, expenses or other claims for consequential
compensation whatsoever and whether caused by negligence of COMEUP employees, distributors
and their employees or otherwise. COMEUP reserves the right to change product design without
notice. In situations in which COMEUP has changed a product design, COMEUP shall have no
obligation to upgrade or otherwise modify previously manufactured products.
英文版操作手冊.indd 13 2017/1/26 上午8:41