Comeup Baby Winch CWS-300 User manual

Compact Winch
Model: CWS-300
PN: 422070 220V 422150 230V 422160 230V
421936 230V 422143 240V 422147 240V
422141 240V 422149 240V 422050 220V
Introduction
Feature
Lifting capacity: 300 kg wire rope top layer
Lifting height: 24 m
Lifting speed: 9 – 13 m/min
Brake: Electromagnetic and mechanical ratchet
Limit protection: Lifting and lowering limiters
Control: Pendant switch powers the winch
Unpacking
．Winch assembly 1pc
．Wire rope 4.8 mm x 25 m (A7X19) 1pc
．Wire rope 5 mm x 25 m(19X7)untwisted for PN:422149 / 422050 1pc
．Weight hook CHW-0033 1pc
．Power lead 1.5 mm2
x 3C x 5 m and plug 1pc
．Power lead 1.5 mm2
x 3C x 3 m and plug for PN:422143/422141 1pc
．Pendant switch PB-417 w/cord 1.25 mm2
x 6C x 10 m 1pc
．Pendant switch PO3.5 w/cord 1.25 mm2
x 6C x 10 m for PN:421936 1pc
Read this manual carefully
You should carefully read and understand this manual before operating it.
Careless winch operation may result in personal injury hazards or property
damage.
Information requesting or parts ordering
Please specify the followings information:
．Winch PN ．Replacement part number
．Serial number ．Quantity for each part
．Part description
Installation
Before using the winch, make sure all electrical components have no
corrosion or damaged; the environment should be clear and dry.
Wire rope replacement
．Put a new wire rope through the hole of the round plate of swivel hook.
．Insert a sleeve pin through the thimble of wire rope.
．Insert a pin through the sleeve pin and bent it by a pliers.
．Let a new wire rope w/clamp through the limit lever and insert it into the
hole of the drum.
．Put a P.T. screw into the hole of the drum and tighten it by a hexagon
wrench.
．Press the ↑button to rotate the drum in the lifting direction.
．An uneven winding of wire rope may cause the load to be swing, thus
damaging the rope and reducing its life.
Wiring Diagram
Warning
．The winch is not intended to be used in any manner for the movement or
lifting of personnel.
．The lifting capacity shown is based on the top layer of rope on the drum.
．The rope winding on the drum shall remain 5 wraps from the drum.

Parts List
Item
No. Description Part No. Qty
1 Gearbox rear cover kit 880493 1
Gearbox rear cover kit for PN:422160 881352
2 Ratchet stopper kit 880547 1
3 Brake kit 881507 1
4 1st gear kit 881498 1
5 3rd gear kit 881508 1
6 4th gear kit 880500 1
7 Gear box kit 880470 1
Gear box kit for PN:422160 881353
8 Hanger kit 880476 1
9 Carbon brush holder 880472 1
10 Carbon brush 220/230/240V 880563 2
11 Over-winding bracket kit 880503 1
12 Wire rope 881244 1
Wire rope untwisted 881419
13 Weight hook CHW-0033 880505 1
Weight hook CHW-0043 for PN:422160 883311
14 Armature core 220/230V 880976 1
Armature core 240V 880977
15 Cooling cover 881500 1
16 Armature winding 220/230V 880518 1
Armature winding 240V 880519
17 Motor rear cover kit 880477 1
Motor rear cover kit for PN:422160 881350
18 Reverse winding shaft kit 880478 1
19 Output shaft kit 880507 1
20 Drum kit 881575 1
21 Control panel 220~240V 881255 1
21-1 D type resistor 220~240V 883328 1
21-2 Limit switch 881503 2
21-3 Diode 881504 2
21-4 D type resistor 220~240V 883329 1
22 Rubber packing 880483 1
23 Electric cover kit 880511 1
Electric cover kit for PN:422160 881354
24 Power lead w/3 flat pins plug for PN:422143/422141 880491 1
Power lead w/3 round pins plug 880492
25 Remote control, PB-417 883145 1
Remote control, PO3.5 881458
Winch Assembly