Congatec SMARC 2.0 conga-SEVAL User manual

Copyright © 2017 congatec AG SEVALm10 1/58
SMARC®2.0 conga-SEVAL
Detailed description of the congatec SMARC 2.0 evaluation carrier board
User’s Guide
Revision 1.0

Copyright © 2017 congatec AG SEVALm10 2/58
Revision History
Revision Date (yyyy.mm.dd) Author Changes
0.1 2017.07.05 AEM •Preliminary release
1.0 2017.10.04 AEM •Corrected the input voltage for connector M24 in table 3 “Connector M23-M24 Descriptions”
•Official release

Copyright © 2017 congatec AG SEVALm10 3/58
Preface
This user’s guide provides information about the components, features and connectors available on the congatec SMARC®2.0 evaluation
carrier board.
Disclaimer
The information contained within this user’s guide, including but not limited to any product specification, is subject to change without notice.
congatec AG provides no warranty with regard to this user’s guide or any other information contained herein and hereby expressly disclaims
any implied warranties of merchantability or fitness for any particular purpose with regard to any of the foregoing. congatec AG assumes
no liability for any damages incurred directly or indirectly from any technical or typographical errors or omissions contained herein or for
discrepancies between the product and the user’s guide. In no event shall congatec AG be liable for any incidental, consequential, special, or
exemplary damages, whether based on tort, contract or otherwise, arising out of or in connection with this user’s guide or any other information
contained herein or the use thereof.
Intended Audience
This user’s guide is intended for technically qualified personnel. It is not intended for general audiences.
Lead-Free Designs (RoHS)
All congatec AG designs are created from lead-free components and are completely RoHS compliant.
Electrostatic Sensitive Device
All congatec AG products are electrostatic sensitive devices and are packaged accordingly. Do not open or handle a congatec AG product
except at an electrostatic-free workstation. Additionally, do not ship or store congatec AG products near strong electrostatic, electromagnetic,
magnetic, or radioactive fields unless the device is contained within its original manufacturer’s packaging. Be aware that failure to comply with
these guidelines will void the congatec AG Limited Warranty.

Copyright © 2017 congatec AG SEVALm10 4/58
Symbols
The following symbols are used in this user’s guide:
Warning
Warnings indicate conditions that, if not observed, can cause personal injury.
Caution
Cautions warn the user about how to prevent damage to hardware or loss of data.
Note
Notes call attention to important information that should be observed.
Connector Type
Describes the connector on the congatec SMARC®evaluation carrier board.
Link to connector layout diagram
This link icon is located in the top left corner of each page. It provides a direct link to the connector layout in section 2 “Connector Layout”.
Copyright Notice
Copyright © 2017, congatec AG. All rights reserved. All text, pictures and graphics are protected by copyrights. No copying is permitted
without written permission from congatec AG.
congatec AG has made every attempt to ensure that the information in this document is accurate yet the information contained within is
supplied “as-is”.

Copyright © 2017 congatec AG SEVALm10 5/58
Trademarks
Product names, logos, brands, and other trademarks featured or referred to within this user’s guide, or the congatec website, are the property
of their respective trademark holders. These trademark holders are not affiliated with congatec AG, our products, or our website.
Warranty
congatec AG makes no representation, warranty or guaranty, express or implied regarding the products except its standard form of limited
warranty (“Limited Warranty”) per the terms and conditions of the congatec entity, which the product is delivered from. These terms and
conditions can be downloaded from www.congatec.com. congatec AG may in its sole discretion modify its Limited Warranty at any time and
from time to time.
The products may include software. Use of the software is subject to the terms and conditions set out in the respective owner’s license
agreements, which are available at www.congatec.com and/or upon request.
Beginning on the date of shipment to its direct customer and continuing for the published warranty period, congatec AG represents that the
products are new and warrants that each product failing to function properly under normal use, due to a defect in materials or workmanship or
due to non conformance to the agreed upon specifications, will be repaired or exchanged, at congatec’s option and expense.
Customer will obtain a Return Material Authorization (“RMA”) number from congatec AG prior to returning the non conforming product freight
prepaid. congatec AG will pay for transporting the repaired or exchanged product to the customer.
Repaired, replaced or exchanged product will be warranted for the repair warranty period in effect as of the date the repaired, exchanged
or replaced product is shipped by congatec, or the remainder of the original warranty, whichever is longer. This Limited Warranty extends to
congatec’s direct customer only and is not assignable or transferable.
Except as set forth in writing in the Limited Warranty, congatec makes no performance representations, warranties, or guarantees, either
express or implied, oral or written, with respect to the products, including without limitation any implied warranty (a) of merchantability, (b) of
fitness for a particular purpose, or (c) arising from course of performance, course of dealing, or usage of trade.
congatec AG shall in no event be liable to the end user for collateral or consequential damages of any kind. congatec shall not otherwise be
liable for loss, damage or expense directly or indirectly arising from the use of the product or from any other cause. The sole and exclusive
remedy against congatec, whether a claim sound in contract, warranty, tort or any other legal theory, shall be repair or replacement of the
product only.
Certification
congatec AG is certified to DIN EN ISO 9001 standard.
C
E
R
T
I
F
I
C
A
T
I
O
N
I
S
O
9
0
0
1
TM

Copyright © 2017 congatec AG SEVALm10 6/58
Technical Support
congatec AG technicians and engineers are committed to providing the best possible technical support for our customers so that our products
can be easily used and implemented. We request that you first visit our website at www.congatec.com for the latest documentation, utilities
and drivers, which have been made available to assist you. If you still require assistance after visiting our website then contact our technical
support department by email at [email protected]
Terminology
Term Description
PCIe Peripheral Component Interface Express (PCI Express)
SDIO Secure Digital Input Output
USB Universal Serial Bus
SATA Serial AT Attachment
HDA High Definition Audio
HDMI High Definition Multimedia Interface
DP DisplayPort
eDP Embedded DisplayPort
DSI Display Serial Interface
MIPI Mobile Industry Processor Interface
CSI Camera Serial Interface
PTP Precision Time Protocol
PWM Pulse Width Modulation
I²C Bus Inter-Integrated Circuit Bus
SPI Serial Peripheral Interface
eSPI Enhanced Serial Peripheral Interface
JTAG Joint Test Action Group
GbE Gigabit Ethernet
LVDS Low-Voltage Differential Signaling
DDC Display Data Channel
N.C. Not connected
N.A. Not available or not applicable
TBD To be determined

Copyright © 2017 congatec AG SEVALm10 7/58
Contents
1 Introduction ............................................................................. 10
1.1 SMARC®Concept .................................................................... 10
1.2 conga-SEVAL .......................................................................... 10
2 Connector Layout .................................................................... 11
3 Specifications........................................................................... 12
3.1 Mechanical Dimensions ........................................................... 12
3.2 Environmental Specifications................................................... 12
3.3 Power Supply ........................................................................... 12
3.3.1 ATX/AT Power Supply.............................................................. 13
3.3.2 DC Power Supply..................................................................... 14
3.3.3 USB Type-C Power Delivery (PD) ............................................. 15
3.4 Jumper Settings for Power Options ........................................ 15
3.4.3.1 Runtime Voltage Control ......................................................... 15
3.4.3.2 Standby Voltage Control.......................................................... 16
3.4.3.3 Supply Voltage for Module ...................................................... 16
3.4.3.4 Power Monitoring (VIN_PWRBAD#)......................................... 17
3.4.3.5 Module Power Path ................................................................. 17
3.5 Status LEDs D68 - D71, D73 - D75 .......................................... 18
3.6 SMARC Battery Support Signals.............................................. 18
3.7 CMOS Battery.......................................................................... 19
4 Connector Subsystem.............................................................. 20
4.1 Communication Buses ............................................................. 25
4.1.1 I2S Bus ..................................................................................... 25
4.1.2 CAN Bus .................................................................................. 25
4.1.3 I2C Bus..................................................................................... 26
4.1.3.1 General Purpose I2C................................................................ 26
4.1.3.2 Power Management I2C .......................................................... 27
4.1.4 eSPI / SPI1................................................................................ 27
4.1.5 SPI............................................................................................ 28
4.2 Boot Selection ......................................................................... 29
4.3 Force Recovery ........................................................................ 29
4.4 Universal Serial Bus (USB) ........................................................ 30
4.4.1 Micro USB Type-AB (OTG)....................................................... 31
4.4.2 Dual Stacked USB Type-A ....................................................... 31
4.4.3 USB Type-C .............................................................................. 31
4.5 PCIe ......................................................................................... 32
4.5.1 PCIe x4 Slot.............................................................................. 33
4.5.2 Mini PCIe.................................................................................. 33
4.5.3 PCIe x1 Slot.............................................................................. 33
4.5.4 M.2........................................................................................... 34
4.6 SIM Card Slot........................................................................... 35
4.7 SD Card Slot ............................................................................ 35
4.8 Gigabit Ethernet (GbE) ............................................................ 36
4.9 MIPI-CSI ................................................................................... 37
4.10 Serial Ports ............................................................................... 38
4.10.1 COM Port 0.............................................................................. 38
4.10.2 COM Port 1.............................................................................. 38
4.10.3 COM Port 2.............................................................................. 39
4.10.4 COM Port 3.............................................................................. 39
4.11 FAN.......................................................................................... 39
4.12 Audio Interfaces....................................................................... 40
4.12.1 MIC-IN ..................................................................................... 41
4.12.2 Line-OUT.................................................................................. 41
4.12.3 S/PDIF OUT ............................................................................. 42
4.13 Display Interfaces..................................................................... 42
4.13.1 DisplayPort++.......................................................................... 43
4.13.2 HDMI ....................................................................................... 43
4.13.3 USB Type C Alternate Display Mode....................................... 44
4.13.4 LVDS / DSI / eDP...................................................................... 45
4.13.4.1 eDP .......................................................................................... 45
4.13.4.2 LVDS / DSI................................................................................ 46
4.13.4.3 Flat Panel and Backlight Power Supply.................................... 47
4.13.4.4 Flat Panel and Backlight Voltage Selection ............................. 48
4.14 SATA ........................................................................................ 49
4.15 HDD Power Connector ............................................................ 50
5 Additional Features.................................................................. 51
5.1 Buttons..................................................................................... 51

Copyright © 2017 congatec AG SEVALm10 8/58
5.1.1 Power....................................................................................... 51
5.1.2 Reset ........................................................................................ 51
5.1.3 LID............................................................................................ 51
5.1.4 Sleep........................................................................................ 52
5.2 Ground Test Points................................................................... 52
5.3 Feature Connector................................................................... 52
5.4 Debug Display Port.................................................................. 54
5.5 GPIO ........................................................................................ 54
5.6 JTAG (Debug Feature) - Internal Use Only .............................. 55
6 Mechanical Dimensions ........................................................... 57
7 Industry Specifications .................................................................

Copyright © 2017 congatec AG SEVALm10 9/58
List of Tables
Table 1 ATX Power (Connector X51) Pinout Description...................... 13
Table 2 Jumper X53 Description .......................................................... 13
Table 3 Connector M23-M24 Description ............................................ 14
Table 4 Connector M25-M26 Description ............................................ 14
Table 5 Jumper X55 Description .......................................................... 16
Table 6 Jumper X59 Description .......................................................... 16
Table 7 Jumper X60 Description .......................................................... 17
Table 8 Jumper X61 Description .......................................................... 17
Table 9 Status LEDs Description........................................................... 18
Table 10 Jumper X52 Description .......................................................... 18
Table 11 CN3 Description ...................................................................... 18
Table 12 Jumper X57 Description .......................................................... 19
Table 13 SMARC Edge Finger Connector Pinout................................... 20
Table 14 Connector X46 Description ..................................................... 25
Table 15 Jumper X47/X49 Description................................................... 25
Table 16 DIP Switch SW1 Description .................................................... 26
Table 17 Connector CN2 Description .................................................... 27
Table 18 DIP Switch M18 Pinout Description ......................................... 28
Table 19 Connector X39 Pinout Description .......................................... 28
Table 20 DIP Switch M17 / M18 Description.......................................... 29
Table 21 Jumper X45 Description .......................................................... 29
Table 22 DIP Switch M11 Description .................................................... 34
Table 23 Connector X8 Pinout Description ............................................ 35
Table 24 Connector CN1 Pinout Description ......................................... 35
Table 25 Connector X14 Pinout Description .......................................... 36
Table 26 Jumper X16 Description .......................................................... 36
Table 27 Connector X13 Pinout Description .......................................... 37
Table 28 Connector X18 Pinout Description .......................................... 38
Table 29 Connector X17 Pinout Description .......................................... 38
Table 30 Connector X42 Pinout Description .......................................... 39
Table 31 Jumper X43 Description .......................................................... 40
Table 32 I2S or HDA Codec Selection.................................................... 40
Table 33 MIC-IN (Connector X19) Pinout Description........................... 41
Table 34 Line_OUT (Connector X21) Pinout Description ....................... 41
Table 35 SPDIF-OUT (Connector X20) Pinout Description..................... 42
Table 36 Jumper X34 Pin Description .................................................... 43
Table 37 Jumper X34 Pin Description .................................................... 44
Table 38 Jumper X35 Pin Description ................................................... 44
Table 39 DIP M12 Pinout Description .................................................... 45
Table 40 Connector X31 / X32 Pinout Description................................. 45
Table 41 Connector X31 / X32 Pinout Description................................. 46
Table 42 Connector X23 Pinout Description .......................................... 47
Table 43 Connector X26 / X30 Pinout Description................................. 48
Table 44 Jumper X22 / X27 Pinout Description ..................................... 48
Table 45 Jumper X25 / X28 Pinout Description ..................................... 49
Table 46 Jumper X24 / X29 Pinout Description ..................................... 49
Table 47 Connector X50 Description ..................................................... 49
Table 48 Connector X58 Description ..................................................... 50
Table 49 Connector X37 Description ..................................................... 52
Table 50 Jumper X56 Description .......................................................... 54
Table 51 GPIO Alternate Function and Routing..................................... 54
Table 52 Jumper X40 Description .......................................................... 55
Table 53 GPIO Connector X38 Description............................................ 55
Table 54 Jumper X44 Description .......................................................... 55
Table 55 Connector X62 Description ..................................................... 56

Copyright © 2017 congatec AG SEVALm10 10/58
1 Introduction
1.1 SMARC®Concept
The Standardization Group for Embedded Technologies e.V (SGET) defined the SMARC standard for small form factor computer modules that
target applications with ultra low power, low cost and high performance. The SMARC connector and interfaces are optimized for high-speed
communication, and are suitable for ARM SoCs and low power x86 SoCs.
The SMARC standard bridges the gap between the COM Express standard and the Qseven standard by offering most of the interfaces defined
in the COM Express specification at a lower power—between 2 W and 6 W during active operation. With a footprint of 82 mm x 50 mm or
82 mm x 80 mm, the SMARC standard promotes the design of highly integrated, energy efficient systems.
Due to its small size and lower power demands, PC appliance designers can design low cost devices as well as explore a huge variety of product
development options—from compact space-saving designs to fully functional systems. This solution allows scalability, product diversification
and faster time to market.
1.2 conga-SEVAL
The conga-SEVAL is designed based on the SMARC Design Guide Specification. By providing most of the functional requirement for any
SMARC application, the conga-SEVAL carrier board provides manufacturers and developers with a platform to jump-start the development of
systems and applications based on SMARC specification. This solution helps to reduce product design cycle and encourages rapid innovation
in system design, to meet the ever-changing needs of the market.
The conga-SEVAL supports both 82 mm x 50 mm and 82 mm x 80 mm SMARC modules and can be used for:
•validating SMARC module
•evaluating customer platform
•debugging or testing production platform
•reference purpose

Copyright © 2017 congatec AG SEVALm10 11/58
2 Connector Layout
The connector layout picture below shows each connector and its name designator. Jumpers and their respective pins are also shown. Select
the Adobe ‘Zoom-In-Tool’ and zoom in on a given component to see its designator. Hover over the component and the ‘Zoom-In-Tool’ will
change indicating there is a link. Click on the link to navigate to the area in the document where the component is described. Use the mouse
icon in the top left hand corner of the destination page to return to the connector layout picture.
HDMI
DP++

Copyright © 2017 congatec AG SEVALm10 12/58
3 Specifications
3.1 Mechanical Dimensions
•294 mm x 172 mm
•Height approximately 25 mm (top side)
3.2 Environmental Specifications
Temperature Operation: 0° to 60°C Storage: -40° to +85°C (commercial temperature)
Temperature Operation: -40° to 85°C Storage: -40° to +85°C (industrial temperature)
Humidity Operation: 10% to 90% Storage: 5% to 95%
Note
The above operating temperatures must be strictly adhered to at all times. The maximum operating temperature refers to any measurable
spot on the modules surface. Humidity specifications are for non-condensing conditions.
3.3 Power Supply
The conga-SEVAL supports the following power sources:
•standard 24-pin ATX power supply (connector X51)
•12 V - 24 V DC variable input power supply (connector M23, M24)
•3 V - 5.25 V DC variable input power supply (connector M25, M26)
•USB Type-C Power Delivery (12V - 20V)

Copyright © 2017 congatec AG SEVALm10 13/58
3.3.1 ATX / AT Power Supply
With an ATX power supply, the SMARC®module starts after the power-on button M19 is pressed. To force the ATX power supply to always be
on, set jumper X53 to position 2-3. This setting is ideal for debugging purposes.
Table 1 ATX Power (Connector X51) Pinout Description
Pin Signal Description Pin Signal Description
1 +3.3V Power Supply +3.3 VDC 13 +3.3V Power Supply +3.3 VDC
2 +3.3V Power Supply +3.3 VDC 14 -12V Power Supply -12 VDC
3 GND Power Ground 15 GND Power Ground
4 +5V Power Supply +5 VDC 16 PS_ON# Power Supply On (active low). Short this
pin to GND to switch power supply ON,
disconnect from GND to switch OFF.
5 GND Power Ground 17 GND Power Ground
6 +5V Power Supply +5 VDC 18 GND Power Ground
7 GND Power Ground 19 GND Power Ground
8 PWR_OK Power Ok 20 N.C Not connected
9 5V_SB Standby Power Supply +5 VDC 21 +5V Power Supply +5 VDC
10 +12V Power Supply +12 VDC 22 +5V Power Supply +5 VDC
11 +12V Power Supply +12 VDC 23 +5V Power Supply +5 VDC
12 +3.3V Power Supply +3.3 VDC 24 GND Power Ground
Table 2 Jumper X53 Description
Pin Configuration
1-2 ATX Mode (Default)
2-3 ATX PSU always on
Connector Type
X51: ATX 2.0 Power Connector
X53: 2.54 mm grid jumper
ATX Power Connector X51
2 31
Jumper X53

Copyright © 2017 congatec AG SEVALm10 14/58
3.3.2 DC Power Supply
The conga-SEVAL features the following connectors for DC power supply:
•12V - 24V DC power supply via connectors M23 and M24
– supplies power to the carrier board and module
•3V - 5.25V DC power supply via connectors M25 and M26.
– supplies power to only the SMARC module
Table 3 Connector M23-M24 Description
Connector Description
M23 Ground
M24 Carrier board input voltage (12 – 24V)
Table 4 Connector M25-M26 Description
Connector Description
M25 Ground
M26 SMARC module input voltage (3.0V – 5.25V)
Connector Type
M23 - M26: 4 mm banana plug
GND
(M23)
12V - 24V
(M24)
GND
(M25)
3.0V - 5.25V
(M26)

Copyright © 2017 congatec AG SEVALm10 15/58
3.3.3 USB Type-C Power Delivery
The conga-SEVAL can be powered by a USB Type-C device attached to connector X4. The USB Type-C port supports USB power delivery up
to 20 V @ 5 A. The port delivers 20 V only when the carrier board receives an input voltage of 20 V. In this mode, the LED D10 glows.
If the input voltage is lower than 20 V, the port provides 12 V or 5 V or both depending on the power delivery profile negotiated with the USB
Type C sink.
Connector Type
X4: USB Type-C receptacle
3.4 Jumper Settings for Power Options
3.4.3.1 Runtime Voltage Control
Use jumper X54 to select the SMARC signal that should enable the runtime voltage of the conga-SEVAL.
Jumper X54 Description
Pin Configuration
1-2 CARRIER_STBY# signal enables carrier board runtime voltages (default)
2-3 CARRIER_PWRON signal enables carrier board runtime voltages
Connector Type
X54: 2.54 mm grid jumper
USB Type-C - X4
D10
2 31
Jumper X54

Copyright © 2017 congatec AG SEVALm10 16/58
3.4.3.2 Standby Voltage Control
Use jumper X55 to select how the conga-SEVAL standby voltages are controlled.
Table 5 Jumper X55 Description
Pin Configuration
1-2 CARRIER_PWRON signal controls the carrier board standby voltages
2-3 Carier board standby voltages are always enabled
Connector Type
X55: 2.54 mm grid jumper
3.4.3.3 Supply Voltage for Module
Use jumper X59 to set the module’s input voltage to 3.3 V or 5 V.
Table 6 Jumper X59 Description
Pin Configuration
1-2 3.3 V
2-3 5 V
Note
Jumper X59 has no effect if the module’s supply voltage is via connector M25 and M26.
Connector Type
X59: 2.54 mm grid jumper
2 31
Jumper X55
2 31
Jumper X59

Copyright © 2017 congatec AG SEVALm10 17/58
3.4.3.4 Power Monitoring (VIN_PWRBAD#)
Use jumper X60 to select the power rail that notifies the module that the operating voltages are within ranges required for operation.
Table 7 Jumper X60 Description
Pin Configuration
1-2 5 V ATX power good signal (only for debugging)
3-4 Carrier board power good signal (M23, M24)
5-6 +3.3V ATX power good signal
7-8 Module power good signal (M25, M26)
2-4 No VIN PWRBAD# control
Connector Type
X60: 2.54 mm, 2x4 pin header
3.4.3.5 Module Power Path
When you power the module via M25 and M26, use jumper X61 to configure how the conga-SEVAL handles the switching of the module’s
power path.
Table 8 Jumper X61 Description
Pin Configuration
1-2 Automatic
2-3 AT_SMARC
Note
Setting jumper X61 to position 2-3 switches the module’s power path to connector M25 and M26, even if the conga-SEVAL is powered via
M23 and M24.
Connector Type
X61: 2.54 mm grid jumper
Jumper X60
1 3
6
5
8
7
2 4
2 31
Jumper X61

Copyright © 2017 congatec AG SEVALm10 18/58
3.5 Status LEDs D68 - D71, D73 - D75
LEDs D68 - D71 indicate the status of the power rails on the conga-SEVAL. LEDs D73 - D75 indicate the voltage source for the SMARC module.
The description of the LEDs is shown in the table below:
Table 9 Status LEDs Description
LED Power State
D68 5 V standby voltage on conga-SEVAL
D69 3.3 V standby voltage on conga-SEVAL
D70 5 V runtime voltage on conga-SEVAL
D71 3.3 V runtime voltage on conga-SEVAL
D73 5 V supplied from conga-SEVAL 5 V DC/DC to SMARC module
D74 3.3 V supplied from conga-SEVAL 3.3 V DC/DC to SMARC module
D75 3.0 V – 5.25 V supplied via connectors M25 and M26 to SMARC module
3.6 SMARC Battery Support Signals
The conga-SEVAL provides SMARC battery support signals on connector CN3. Set jumper X52 to position 1-2 if a smart battery system is
connected to conga-SEVAL. This setting ensures the conga-SEVAL enables the necessary DC/DC voltage regulators.
Table 10 Jumper X52 Description
Pin Configuration
1-2 SBM3 present
2-3 SBM3 not present
Table 11 CN3 Description
Pin Signal
1 CHARGING#
2 CHARGER_PRSNT#
3 BATLOW#
4 GND
D68 D69 D70 D71 D73 D74 D75
2 31
Jumper X52
CN3 - Battery Support

Copyright © 2017 congatec AG SEVALm10 19/58
Connector Type
CN3: 2.00 mm, 1 x 4 box header
X52: 2.54 mm grid jumper
3.7 CMOS Battery
The conga-SEVAL provides a board-mounted battery holder (M27) for a CMOS battery. The CMOS battery supplies the power required to
maintain the module’s RTC and CMOS memory. The required battery type on the conga-SEVAL is CR2032.
Set jumper X57 to position 2-3 to disconnect the RTC battery.
Table 12 Jumper X57 Description
Pin Configuration
1 - 2 Connect RTC battery (default)
2 - 3 Disconnect RTC battery
Connector Type
X57: 2.54 mm grid jumper
Warning
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
CMOS Battery - M27
2 31
Jumper X57

Copyright © 2017 congatec AG SEVALm10 20/58
4 Connector Subsystem
Table 13 SMARC Edge Finger Connector Pinout
P-PIN Primary (Top) Side S-Pin Secondary (Bottom) Side
S1 CSI1_TX+ / I2C_CAM1_CK
P1 SMB_ALERT_1V8# S2 CSI1_TX- / I2C_CAM1_DAT
P2 GND S3 GND
P3 CSI1_CK+ S4 RSVD
P4 CSI1_CK- S5 CSI0_TX- / I2C_CAM0_CK
P5 GBE1_SDP S6 CAM_MCK
P6 GBE0_SDP S7 CSI0_TX+ / I2C_CAM0_DAT
P7 CSI1_RX0+ S8 CSI0_CK+
P8 CSI1_RX0- S9 CSI0_CK-
P9 GND S10 GND
P10 CSI1_RX1+ S11 CSI0_RX0+
P11 CSI1_RX1- S12 CSI0_RX0-
P12 GND S13 GND
P13 CSI1_RX2+ S14 CSI0_RX1+
P14 CSI1_RX2- S15 CSI0_RX1-
P15 GND S16 GND
P16 CSI1_RX3+ S17 GBE1_MDI0+
P17 CSI1_RX3- S18 GBE1_MDI0-
P18 GND S19 GBE1_LINK100#
P19 GBE0_MDI3- S20 GBE1_MDI1+
P20 GBE0_MDI3+ S21 GBE1_MDI1-
P21 GBE0_LINK100# S22 GBE1_LINK1000#
P22 GBE0_LINK1000# S23 GBE1_MDI2+
P23 GBE0_MDI2- S24 GBE1_MDI2-
P24 GBE0_MDI2+ S25 GND
P25 GBE0_LINK_ACT# S26 GBE1_MDI3+
P26 GBE0_MDI1- S27 GBE1_MDI3-
P27 GBE0_MDI1+ S28 GBE1_CTREF
P28 GBE0_CTREF S29 PCIE_D_TX+
P29 GBE0_MDI0- S30 PCIE_D_TX-