Consort D230 User manual

D230
June 2011
Consort
MANUAL
HANDLEIDING
MODE D’EMPLOI

D230 èwww.consort.be 2
Introduction
This instrument is manufactured with the latest technology and needs no particu-
lar maintenance. Consort certifies that this instrument was thoroughly inspected
and tested at the factory prior to shipment and found to meet all requirements
defined by contract under which it is furnished. However, dimensions and other
physical characteristics may differ.
The normal operating temperature should be between 0° and 40°C. Never use
the instrument in a room with high humidity (>95 %) or at very low temperatures
(condensation water!).
Connect the instrument only to an earthed power line. The required power source
is indicated on the label at the back of the instrument. Do not cut and splice the
power cord. When removing the power cord from the wall outlet, be sure to unplug
by holding the plug attachment and not by pulling the cord. Do not hold the plug
by wet hand.
Manufacturer
Consort bvba
Parklaan 36 Tel (+32)(14)41 12 79
B2300 Turnhout Fax (+32)(14)42 91 79
Belgium E-mail: [email protected]
Warranty
This instrument (excluding all accessories) is warranted against defective material
and workmanship for a period of thirty-six (36) months from the date of shipment
ex factory. Consort will repair all defective equipment returned to it during the
warranty period without charge, provided the equipment has been used under
normal laboratory conditions and in accordance with the operating limitations and
maintenance procedures in this instruction manual and when not having been
subject to accident, alteration, misuse or abuse. A return authorisation must be
obtained from Consort before returning any product for warranty repair on a
freight prepaid basis!
Consort is not liable for consequential damages arising out of the use or handling
of its products.
Servicing
In the event of this instrument being returned for servicing, the owner is requested
to remove the power supply lead and NOT to send the following items unless they
are suspect:
Manual
Cables
Accessories
If serious malfunctioning occurs, stop using the unit immediately and consult your
local Consort dealer.
Connections
1. The electrodes should be connected to the coaxial BNC connectors.
2. Automatic temperature compensation and temperature measurements are
possible by plugging a Pt1000 thermocompensator into the corresponding
banana terminals. Without compensator, the manual temperature compensa-
tion is automatically switched on.
3. Connect the first rack to the serial port of the computer using the RS232 cable
(DP9) supplied with the system.
4. Connect additional racks with each other and to the first rack using the special
cables D298.
5. Install the software on the computer and read the help file for further instruc-
tions.

D230 èwww.consort.be 3
Inleiding
Dit toestel is gebouwd volgens de modernste technologie en hoeft niet speciaal te
worden onderhouden. Consort bevestigt dat dit toestel grondig werd nagekeken
en getest alvorens te worden verstuurd, en beantwoordt aan alle vereisten van het
aankoopkontrakt. Er kunnen echter wel afwijkingen optreden in de afmetingen en
andere fysische eigenschappen. De normale werktemperatuur moet tussen 0° en
40°C liggen. Gebruik het toestel nooit in een ruimte met hoge vochtigheidsgraad
(>95 %) of bij zeer lage temperaturen (condenswater!).
Verbind het toestel uitsluitend met een geaard stopcontact. Controleer de juiste
netspanningswaarde op de achterwand alvorens het apparaat aan te sluiten op het
net. Maak geen insnijdingen of onderbrekingen in het netsnoer. Houd het netsnoer
steeds met de stekker vast om het uit het stopcontact te verwijderen en trek nooit
aan het snoer zelf. Zorg er steeds voor met droge handen te werken.
Fabrikant
Consort bvba
Parklaan 36 Tel (+32)(14)41 12 79
B2300 Turnhout Fax (+32)(14)42 91 79
België E-mail: [email protected]
Waarborg
Dit toestel (uitgezonderd alle toebehoren) is gewaarborgd tegen defect materi-
aal of constructiefouten voor een periode van zesendertig (36) maanden vanaf
de verzenddatum af fabriek. Consort zal elk toestel gratis herstellen, binnen
de waarborgperiode, voor zover het werd gebruikt onder normale laboratorium
omstandigheden volgens de werkvoorschriften en onderhoudsprocedures uit deze
gebruiksaanwijzing en wanneer de oorzaak van het defect niet een ongeluk, een
aanpassing, verkeerd gebruik of misbruik is. Er moet eerst een toelating van
Consort verkregen worden vooraleer eender welk toestel franco terug te sturen
voor herstelling onder waarborg!
Consort kan niet aansprakelijk worden gesteld voor eventuele schadelijke gevol-
gen van het gebruik of behandeling van zijn producten.
Onderhoud
Mocht dit toestel worden teruggestuurd voor onderhoud, gelieve het netsnoer af te
koppelen en volgende toebehoren NIET mee te sturen, tenzij ze verdacht zijn:
Handleiding
Kabels
Toebehoren
In geval van ernstige storing, stop onmiddellijk het gebruik van het toestel en
raadpleeg uw plaatselijke Consort verdeler.
Verbindingen
1. De elektroden moeten met de BNC-ingangen verbonden worden.
2. Automatische temperatuurcompensatie en meting zijn mogelijk wanneer
Pt1000 thermocompensators aan de banaan-klemmen aangesloten worden.
Zonder Pt1000 is de manuele temperatuurcompensatie automatisch ingescha-
keld.
3. Verbind het eerste meetrek met de seriële poort van de computer met behulp
van de bijgeleverde RS232 kabel (DP9).
4. Verbind de andere meetrekken onderling en met het eerste meetrek met
behulp van de speciale kabels D298.
5. Installeer de software op de computer en lees het help-bestand voor verdere
instructies.

D230 èwww.consort.be 4
Préface
Cet appareil est construit selon les dernières technologies et ne nécessite aucun
entretien particulier. Consort certifie que cet appareil a été contrôlé et vérifié
sévèrement à l'usine avant livraison afin de convenir aux exigences définies par le
contrat d'achat. Néanmoins, il peut y avoir des différences dans les dimensions ou
autres caractéristiques physiques.
La température d'utilisation normale doit être entre 0° et 40°C. N'utilisez jamais
l'appareil dans un lieu humide (>95 %) ou à une température très basse (conden-
sation d'eau!).
Brancher l'appareil uniquement à une prise avec terre. N'utiliser qu'une source
d'alimentation électrique correspondante aux indications figurant au dos de l'appa-
reil. Ne pas couper ou réparer le cordon d'alimentation. En débranchant le cordon
de la prise, ne jamais tirer sur le cordon lui même mais toujours saisir la fiche. Ne
jamais saisir la fiche de raccordement avec des mains mouillées.
Fabricant
Consort bvba
Parklaan 36 Tel (+32)(14)41 12 79
B2300 Turnhout Fax (+32)(14)42 91 79
Belgique E-mail: [email protected]
Garantie
Cet appareil (sauf tous les accessoires) est garanti pendant trente-six (36) mois, à
partir de la date d'expédition départ usine, contre toute faute du matériel et main
d'oeuvre. Consort réparera gratuitement chaque appareil défectueux, qui lui est
retourné, à condition que l'appareil a été utilisé dans des conditions normales de
laboratoire selon les limitations opérationnelles et les procédés d'entretien de ce
mode d'emploi et que le défaut n'est pas dû à un accident, une adaptation, un mal-
traitement ou un abus. Avant de retourner, aux frais de l'utilisateur, tout appareil
pour réparation sous garantie, il faut d'abord obtenir l'approbation de Consort!
Consort décline toute responsabilité pour des dommages éventuels causés par
l'usage ou la manipulation de ses produits.
Service
En cas de retour de cet appareil pour service après vente, débrancher le cordon
secteur et NE PAS renvoyer les accessoires suivants, sauf s'ils sont suspects:
Mode d'emploi
Câbles
Accessoires
En cas de mauvais fonctionnement sérieux, arrêtez d'utiliser l'appareil immédiate-
ment et consultez votre agent Consort local.
Connections
1. Raccordez les électrodes aux prises BNC.
2. Afin de pouvoir faire une compensation automatique ainsi que des mesures
de la température, branchez des sondes de température Pt1000 aux prises
banane. Si vous n'utilisez pas de Pt1000, la compensation manuelle est auto-
matiquement en fonction.
3. Raccordez la première centrale au port série de l'ordinateur au moyen du câble
RS232 (DP9) fourni avec le système.
4. Raccordez les autres centrales entre elles, puis avec la première centrale, au
moyen des câbles D298.
5. Installez le logiciel sur l'ordinateur et lisez le fichier aide pour des instructions
supplémentaires.

Temp. 1.68 4.01 6.87 9.18 12.45 NIST buffers
0°C 1.666 pH 4.003 pH 6.984 pH 9.464 pH 13.423 pH
5°C 1.668 pH 3.999 pH 6.951 pH 9.395 pH 13.207 pH
10°C 1.670 pH 3.998 pH 6.923 pH 9.332 pH 13.003 pH
15°C 1.672 pH 3.999 pH 6.900 pH 9.276 pH 12.810 pH
20°C 1.675 pH 4.002 pH 6.881 pH 9.225 pH 12.627 pH
25°C 1.679 pH 4.008 pH 6.865 pH 9.180 pH 12.454 pH
30°C 1.683 pH 4.015 pH 6.853 pH 9.139 pH 12.289 pH
40°C 1.694 pH 4.035 pH 6.838 pH 9.068 pH 11.984 pH
50°C 1.707 pH 4.060 pH 6.833 pH 9.011 pH 11.705 pH
60°C 1.723 pH 4.091 pH 6.836 pH 8.962 pH 11.449 pH
70°C 1.743 pH 4.126 pH 6.845 pH 8.921 pH
80°C 1.766 pH 4.164 pH 6.859 pH 8.885 pH
Temp. 3 M KCl Redox standard
0°C 224 mV
5°C 219 mV
10°C 214 mV
15°C 212 mV
20°C 204 mV
25°C 199 mV
30°C 194 mV
35°C 189 mV
40°C 184 mV
45°C 179 mV
50°C 174 mV
Temp. 0.01 M 0.1 M 1 M Conductivity standards
0°C 776 µS 7.15 mS 65.4 mS
5°C 896 µS 8.22 mS 74.1 mS
10°C 1020 µS 9.33 mS 83.2 mS
15°C 1147 µS 10.48 mS 92.5 mS
20°C 1278 µS 11.67 mS 102.1 mS
25°C 1413 µS 12.88 mS 111.8 mS
30°C 1552 µS 14.12 mS 121.7 mS
Temp. 4.00 7.00 9.21 10.01 Standard buffers
5°C 3.99 pH 7.08 pH 9.45 pH 10.24 pH
10°C 3.99 pH 7.06 pH 9.38 pH 10.18 pH
20°C 3.99 pH 7.02 pH 9.26 pH 10.06 pH
25°C 4.00 pH 7.00 pH 9.21 pH 10.01 pH
30°C 4.01 pH 6.99 pH 9.16 pH 9.97 pH
40°C 4.03 pH 6.98 pH 9.06 pH 9.89 pH
50°C 4.06 pH 6.97 pH 8.99 pH 9.83 pH
60°C 4.09 pH 6.98 pH 8.93 pH 9.79 pH

Specifications D230
pH Range 0...14 pH
Resolution 0.001 pH
Accuracy 0.1% ± 1 digit
Calibration 1...2 points
Buffers 9 pre-programmed
2 user specified
Temperature Compensation -30...+130°C
ISO-pH 6...8 pH
Slope 80...120%
mV Range ±2000 mV
Resolution 0.1 mV
Accuracy 0.1% ± 1 digit
Calibration 1 point
ION Range 0.01 ng/l...100 g/l
Resolution 3 digits
Accuracy 0.5% ± 1 digit
Calibration 2 points + blank
DISS. OXYGEN Range 0...60 mg/l (0...600%)
Resolution 0.01 mg/l (0.1%)
Accuracy 1% ± 1 digit
Calibration 1 point
Temperature Compensation 0...50°C
CONDUCTIVITY Range 0...2000 mS/cm
Resolution 0.001 µS/cm
Accuracy 0.5% f.s. of range
Calibration 1 point
Standards 0.01/0.1/1 M KCl
3 user specified
Cell Constant 0.01/0.1/1/10 cm-1 ± 50%
Temperature Compensation -30...+130°C
Reference Temperature 20° or 25°C
Temperature Coefficient natural waters (EN27888)
Capacitive Compensation ü
TDS Range 0...100 g/l
Resolution 0.01 mg/l
TEMPERATURE Range -30...+130°C
Resolution 0.1°C
Accuracy 0.3°C
Calibration ±10°C
CHANNELS pH/mV/Ion/Oxygen 4...28
Conductivity 4...28
Temperature 4...28
INPUTS pH/mV/Ion/Oxygen BNC, 1012 Ω
Conductivity BNC
Temperature 2 banana, for Pt1000
CALIBRATION GLP ü
DATA-LOGGING Values/channel unlimited + °C/date/time
Interval 4 s ... 24 h
SOFTWARE Languages EN, NL, FR
SECURITY Password Protection ü
POWER SUPPLY Mains 210...250 VAC
DIMENSIONS WxDxH 48x24x13 cm
WEIGHT Meter 12 kg

WARRANTY CERTIFICATE
This instrument (excluding all accessories) is warranted against defective material and
workmanship for a period of thirty-six (36) months from the date of shipment ex fac-
tory.
CONSORT will repair all defective equipment returned to it during the warranty period
without charge, provided the equipment has been used under normal laboratory condi-
tions and in accordance with the operating limitations and maintenance procedures in
this instruction manual and when not having been subject to accident, alteration, misuse
or abuse.
A return authorisation must be obtained from CONSORT before returning any product for
warranty repair on a freight prepaid basis!
DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
Multi-parameter analyser
content of the type numbers
D230, D291, D292
to which this declaration relates is in conformity
with the following standards
EN61010
LOW VOLTAGE DIRECTIVE 73/23/EEG
EN50081-1
EN50082-1
EN60555-2
EMC DIRECTIVE 89/336/EEG
Turnhout, June 20, 2002
on behalf of Consort bvba
Table of contents
Languages:
Other Consort Measuring Instrument manuals

Consort
Consort Z621 User manual

Consort
Consort C931 User manual

Consort
Consort R735 User manual

Consort
Consort K912 User manual

Consort
Consort C3010 User manual

Consort
Consort C6010 User manual

Consort
Consort T871 User manual

Consort
Consort LabArt C51 User manual

Consort
Consort R311 User manual

Consort
Consort K611 User manual
Popular Measuring Instrument manuals by other brands

PCB Piezotronics
PCB Piezotronics 3711F112G Installation and operating manual

LSI LASTEM
LSI LASTEM Heat Shield Quick user guide

QuadTech
QuadTech 1730T instruction manual

Extech Instruments
Extech Instruments DC400 user guide

Lutron Electronics
Lutron Electronics CT-2012 Operation manual

Deif
Deif XDi Series Designers handbook