Contura C 850 User manual

C 850
www.contura.eu
Installation
Instructions

GB
50 CERTIFICATE
PRODUCT
Product type Stove lit with solid biofuels
Type designation Contura 850
Manufacturing number See rating plate on the stove
Intended area of use Heating of rooms in residential buildings
Fuel Wood
MANUFACTURER
Name NIBE AB / Contura
Address Box 134, Skulptörvägen 10
SE-285 23 Markaryd, Sweden
CHECKS
According to AVCP System 3
European standard EN 13240:2001 / A2:2004
Test institute Rein-Ruhr Feuerstätten Prüfstelle, NB 1625,
has checked declared performance and issued test report no. RRF-40 11 2656
PERFORMANCE DECLARATION
No. C850-CPR-130610-SE-1
DECLARED PERFORMANCE
Essential characteristics Performance Harmonised technical
specification
Reaction to fire A1 WT
Minimum distance to combustible material 100 mm to rear
500 mm to side
Other safety distances according to
the installation instructions
Risk of falling embers Approved
Emissions from combustion CO 0.07%
NOx 98 mg/m3
OGC 51 mg/m3
PM 20 mg/m3
Surface temperatures Approved
Cleaning options Approved
Mechanical durability Approved
Emissions of hazardous substances Approved
Nominal output 4 kW
Efficiency 82%
Flue gas temperature in connector at nominal
output
320°C
EN 13240:2001 / A2:2004
The undersigned is responsible for the manufacture and conformity with the declared performance.
Niklas Gunnarsson, Business area manager NIBE STOVES
Markaryd, 1st July 2013

GB
51
Table of contents
Technical details 52
Prior to installation 53
Connection to chimney 54
Supply of combustion air/Option 55
Installation distances 56
Assembly 57
Removal 58
A warm welcome to Contura.
A warm welcome to the Contura family. We hope
you will get a great deal of pleasure from your new
stove. As a new owner of a Contura stove you have
secured a product with timeless design and long
service life. Contura also has combustion that is both
environmentally friendly and efficient for the best heat
production.
Read through these installation instructions carefully
before installation. Read how to best light your stove
in the lighting instructions.
CONTENTS

GB
52
NOTE!
Report the installation of a stove to your local
authority.
The owner of the house is personally responsible
for ensuring compliance with the mandatory safety
requirements and must have the installation approved by
a qualified inspector. Your local chimney sweep must also
be informed about the installation as this will affect the
routines for regular chimney-sweeping services.
WARNING!
The stove becomes very hot
During operation, certain surfaces of the stove become
very hot and can cause burn injury if touched. Be aware
of the strong heat radiated through the hatch glass.
Placing flammable material closer than the safe distance
indicated may cause a fire. Pyre lighting can cause quick
gas ignition with the risk of damage to property and
personal injury.
FACTS
Output 3-6 kW
Nominal output 4 kW
Efficiency up to 82%
Model 850
Height (mm) 915
Width (mm) 460
Depth (mm) 360
Weight (kg) 85
Type approved in accordance with:
European standard EN-13240
Swedish approval
Norwegian standard NS 3059
German standard DIN Plus
Installation by authorised
technician
This manual contains instructions about
how the stoves must be assembled and
installed. To ensure the function and safety
of the stove, we recommend that the
installation is carried out by an authorised
technician. Contact one of our dealers who
can recommend suitable technicians.
Building application
These main instructions may give guidance
which would contravene national building
regulations. Please refer to supplementary
instructions or ask your local authority for
advice regarding building regulations.
Before installing a stove or erecting a
chimney it is necessary for you to make
a building application permission to your
local authority.
Structural support
Check that the wood joists are strong
enough to bear the weight of the stove and
chimney. The stove and chimney can usually
be placed on a normal wooden joist in a
single occupancy house if the total weight
does not exceed 400 kg.
Hearth plate
Due to the risk of falling embers, a
flammable floor must be protected by a
hearth plate. It must extend 300 mm in
front of the stove and 100 mm on each side
of the stove, or have a 200 mm extension
on each side of the opening. The hearth
plate can consist of natural stone, concrete,
metal plate or glass. A painted metal
or glass hearth plate is available as an
accessory for these models.
Important to remember!Technical details

1
2
3
4
5
GB
53
PRIOR TO INSTALLATION
Prior to installation
If the insert needs to be put down to
be moved, loose components should
be removed. This is described at the
end of these installation instructions.
1 Fire bars
2 Grate disc
3 Fire bricks
4 Type plate
5 Hot air grate

Ø
ca 180 mm
Ø
ca 180 mm
2 31
5 6
4
!
GB
54 CHIMNEY
Connection to chimney
Rear connection to a masonry chimney
Top connection to the chimney
Make sure that the connector
gasket does not work loose when
the connection pipe is placed
on the connector. If further
sealing material is required, heat-
resistant sealant may be used.
The hot air grille must be installed before chimney top
connection.
• The stove meets the requirements for connecting to chimneys
dimensioned for 350°C flue gas temperature.
• The external diameter of the connection sleeve is 150 mm.
• The stove requires a draft in the chimney of at least –12 Pa. The
draft is affected both by the length and area of the chimney, and
by how well sealed it is. Minimum recommended chimney length
is 3.5 m and suitable cross section area is 150-200 cm² (140-160
mm in diameter).
• A flue with sharp bends and horizontal routing reduces the
draught in the chimney. Maximum horizontal flue is 1 m, on the
condition that the vertical flue length is at least 5 m.
• It must be possible to sweep the full length of the flue and the
soot hatches must be easily accessible.
• Carefully check that the chimney is sealed and that there is no
leakage around soot hatches and flue connections.
In the bag with these installation instructions
are two wing screws for the cover.

!
HK
HK
40 mm
HK
40 mm
HK
40 mm
GB
55
SUPPLY AIR/ACCESSORY
Supply of combustion air
When a stove is installed in a room, the demand for air supply to the room
increases. Air can be provided indirectly via a vent in the outer wall or via a
duct from the outside that is connected to the connector on the underneath
of the stove. The amount of air needed for combustion is 20m3/h.
The connector has an external diameter of 67 mm. When duct routing
further than 1 m the pipe diameter must be increased to 100 mm and a
correspondingly larger wall vent must be selected.
In hot areas the duct should be insulated with 30 mm mineral wool covered
with a moisture inhibitor (plastic). It is important that the lead-in between
the pipe and the wall (or floor) is sealed using jointing compound.
A 1 m length of condensation insulated ducting for combustion air is
available as an accessory.
Through the external wall.
Indirect air supply through the external wall.
Through floor and foundation slab.
Through floor and wall-and-cavity foundation.
Installation variants
Leave a 40 mm gap between
the condensation insulation
and the bottom of the stove.
Outside air can be connected through the floor
plate or at two different heights through the
two panels in the back of the stove. Tap out the
knockout using a hammer.

C 850
GB
56
730
500
300
200
400
100
200
300
280
100
Combustible wall
INSTALLATION DISTANCES
* If the stove is placed on a hearth plate made of glass for example (accessory), the height from the floor is affected by a distance corresponding to the thickness of the hearth plate. Also applies to
separate glass hearth plates (accessory).
** To prevent discolouration of painted non-flammable walls we recommend that the same side distance as to combustible walls is used.
The minimum distance in front of
the stove opening to combustible
parts of the building or interior
decoration must be at least 1 m.
The dimension diagrams only
show the minimum permitted
installation distances for the
stove. When connecting to a steel
flue, also note the safety distance
requirements of the flue. The
safety distance between an un-
insulated flue and a combustible
part of the building should be at
least 450 mm.
Installation distances
WHEN INSTALLING TURNTABLE (OPTION) the fol-
lowing installation distances do not apply.
See the separate turntable installation instructions.
A = height from floor to chimney
connection upwards
B = height from floor to c/c chimney
connection rear
C = height from floor to air inlet
D = height from floor to lower edge
of hatch
Permitted area for
combustible parts
of the building
A separate glass hearth
plate (accessory) increases
the connection height to
the chimney by 6 mm.
460
915
D 335
2000
100
200
Combustible roof
360
180
A 877*
115
B 785*
C 300
45
Ø150
Air inlet Ø67
428
656
200
200
Combustible wall
430**
700
1000
230
50
200**
Fire-retardant wall of
brick or concrete
278**
506**
50**
50**
Fire-retardant wall of
brick or concrete
!

3
4
21
13
13
VANADIUM
No. 7
CHROME
GB
57
ASSEMBLY
Installing C 850
Final inspection of the installation
It is extremely important that the installation is inspected by an authorised chimney sweep before
the stove is used. Also read the ”Lighting instructions”, before lighting for the first time.

1
3
2
GB
58 REMOVAL
How to remove the fire bricks
Handle the vermiculite with care. Lift the smoke baffle with one hand whilst
removing the sides. The side posts need not be removed when sweeping. Reinstall
in reverse order.
Removal

811238 IAV SE-EX C850-3
2014-10-13
Contura reserves the right to change dimensions and
procedures described in these instructions at any time without
special notice. The current edition can be downloaded from
www.contura.eu
NIBE AB · Box 134 · 285 23 Markaryd · Sweden
www.contura.eu