Contura Turntable C500 User manual

NIBE AB · Box 134 · 285 23 Markaryd · Suède
www.contura.eu
Installation
instruction
Turntable
C500/C600
www.contura.eu

GB
51
The owner of the house is personally responsible for ensur-
ing compliance with the mandatory safety requirements and
must have the installation approved by a qualified inspec-
tor. Be aware of the strong heat radiated through the hatch
glass. Placing combustible material closer than the safe dis-
tance indicated may cause a fire.
General
These instructions explain how to install a stove on a turntable
base. Read these installation instructions carefully before installa-
tion. The turntable enables you to rotate the stove to the desired
viewing position. Depending on the installation alternative chosen,
the stove may be adjusted to any position within a 90° or 180° wide
angle. If the stove is placed free-standing in the centre of a room
away from a combustible wall, it is also possible to rotate the stove
through a full 360°. The axis of rotation is a notional line that rises
from the centre of rotation of the turntable itself, up through the
body of the stove and through the centre of the sleeve that con-
nects the top of the stove to the flue above.
For direct supply of combustion air from outdoors through the
turntable a separate outdoor air connection is required (acces-
sory). Connection is carried out in conjunction with the installation
of the turntable according to the instructions provided with the
outdoor air connection.
Safety zone
No combustible constructional or decorative element must come
within the prescribed safety zone at any time. Note that the size
of the safety zone varies depending on the type of installation and
the angle of rotation. Follow the instructions and check the safety
zone is free when the turntable is rotated.
Floor plate
Always bear in mind how the stove will be rotated when calculating
the size of the floor plate required. For information about the size
of the floor plate, please refer to the installation instructions sup-
plied with the stove itself. It is always essential that the surface
on which the floor plate stands is flat and level under all circum-
stances.
The turntable is suitable for the following models:
Contura 510, 520T, 550, 550A, 556, 586, 560K, 560T, 570,
580, 585, 590, 590T.
Contura 620T, 630, 630T, 635, 650, 655, 660K, 660T.
!
Vridcentrum
Axis of rotation

GB
52
Installation distance to combustible walls
The distances between stove and wall must always be at least as
great as those specified in the diagrams below. Measurements
are given in mm. Follow the instructions on page 52 for correct
location of the turntable.
When connecting combustion air through the turntable, the cen-
tre of the supply air hole in the floor (Ø100) must be at the same
distance as the turntable’s axis of rotation. Installation dimen-
sions, A and B, refer to measurement from wall to axis of rotation.
Contura 510, 520, 520T, 590T
Contura 556, 556T, 586, 596, 596T
Angle of rotation 90°
Angle of rotation 90° Angle of rotation 180°
Angle of rotation 180°
Angle of rotation 90° Angle of rotation 180°
Contura 620T, 630, 630T, 635, 650, 655, 660K, 660T
Non-combustible wall
The gap between the stove and a non-combustible wall,
classed as a fire-wall, may be as little as 50 mm. When
installing against a non–combustible wall, always ensure
that the turntable can rotate freely. The eccentric rotation
can affect the free rotation. Note that heat radiation can
discolour painted walls.
45° 45°
0°
B=1330
A=310
Combustible wall
Safety zone
A
n
g
l
e
o
f
r
o
t
a
t
i
o
n
B=1330
A=800
90° 90°
0°
Combustible wall
Safety zone
A
n
g
l
e
o
f
r
o
t
a
t
i
o
n
B=1330
A=800
90° 90°
0°
Combustible wall
Safety zone
A
n
g
l
e
o
f
r
o
t
a
t
i
o
n
B=1330
A=325
45°
45°
0°
Combustible wall
Safety zone
A
n
g
l
e
o
f
r
o
t
a
t
i
o
n
B=1330
A=800
90° 90°
0°
Combustible wall
Safety zone
A
n
g
l
e
o
f
r
o
t
a
t
i
o
n
45° 45°
0°
B=1330
A=410
Combustible wall
Safety zone
A
n
g
l
e
o
f
r
o
t
a
t
i
o
n

GB
53
Adapting the stove
Stove with Foot
Stove with Pedestal
Follow the stove’s installation instruc-
tions when mounting the insert’s foot
pedestal.
!

GB
54
Positioning and Installation
The bottom section of the turntable is positioned so that installa-
tion dimensions A and B are met. Note that A and B are different
depending on the model and angle of rotation. The bottom section
is positioned on a secure, flat surface. If possible, the bottom sec-
tion can be secured in the floor surface using screws. The arrow
on the bottom section marks the stove’s neutral position where it
can be turned an equal amount in both directions. If the turntable/
stove is to be connected to a supply air duct in the floor, an out-
door air connector (accessory) is required.
Outdoor air connection (accessory)
x10
90°
A
B
x9

GB
55
90°
180°
360°

GB
56
The turntable brake is preset and should not normally be
changed. It can be adjusted after the stove is installed on
the turntable. Rotate the turntable until the panel protrudes
under the cut out in the upper section of the turntable.
Then adjust the brake force.

GB
57
Check that the axis of rotation of the turntable is the correct
distance from combustible walls, check that A and B are met
according to page 2. Also check that there is no combustible
material in the safety zone.
Make the marking for hole in the ceiling when the turntable has
been positioned. Work from the centre axis of the turntable.
Checking safety zone
Making hole for chimney
B=1330
A

GB
58
Stove with Foot
Assembling the stove
C500
C600

GB
59
Stove with Pedestal
Unscrew the two screws holding the factory installed collar and
replace it with the rotating collar, carried on bearings, supplied with
the turntable.
Installing rotating collar
1 2
3

NIBE AB · Box 134 · SE-285 23 Markaryd · Sweden
www.contura.eu
811071 IAV SE-EX Turntable 2010 C500/C600-2
2015-09-21