Converters.TV 15385 User manual

UHD Matrix 4in 2out HDCP 2.2
- # 15385
Operation Manual

Introduction
The 6G UHD 4 by 2 HDMI Wall Plate Matrix is the most advance HDMI solution
or your true Ultra High-De inition signal distribution. It allows you to manipulate
one 6G HDMI input signals with switching into two 6G HDMI displays
simultaneously. With supports 4K2K@60, 48-bit Deep Color, Hi-De audio and other
eatures de ined by HDMI speci ications. The device can be operated easily through
Telnet, WebGUI, IR remote and on-panel controls.
pplications
•Entertainment Room / Home Theater
•Show Room / Demo Room
•Lecture Room/Hall Presentation
•Show Room/Demo Room
•Public Commercial Display
Features
•HDMI with 6G 4Kx2K supported, HDCP 2.2 and DVI compliant
•Supports 4 HDMI inputs o one 6G and 2 HDMI outputs o two 6G
•Supports HDTV resolutions up to 4Kx2K (3840x2160@24/25/30/50/60 &
4096x2160 @24/25/30/50/60Hz)
•Supports data rate up to 6Gbps and Deep Color up to 1080p 48-bit
•Supports pass-through o HD audio ormats o LPCM 2/5.1/7.1CH, Dolby
Digital 2~5.1CH, DTS 2~5.1CH, Dolby Digital Plus, Dolby TrueHD, Dolby
Atmos and DTS-HD Master Audio
•Compliant with DVI source
System
Requirements
Input source equipment such as Blu-ray/DVD/PS3 player or Set-Top-Box and output
HDMI TV/Display and or audio ampli ier with connection cables.

Operation Top Panel
Controls and
Functions
1. POWER: Press the Power key to turn on the device and the LED will illuminated in
green, press again to set it to standby mode and the LED will turn red. This device
obtain power last memory unction there ore, when power supply is re-plugged it will
return to last power status.
2. IR Window: This IR Receiver receives IR signal rom the remote control included in
the package only.
3 OUTPUT 1~ 4 & B1~B4: Press these IN buttons to select or each output with an input source to
display.
Left Panel
1. HDMI IN 1~4: Connect rom source equipment such as Blu-ray/ DVD/PS3 player,
Set-Top Box or any HDMI equipped source device or input signal sending.
Note: Only port 1 supports 6G signal and other ports support up to 3G signal.

Right Panel
1. HDMI OUT ~B: Connect to HDMI TV / display or HD ampli ier or output image
and audio or audio display up to 6G each port.
Bottom Panel
1. L N: Connect to PC / Laptop with active internet service or Telnet / WebGUI control
with RJ-45 terminated cable.
2. RS232: Connect to PC / Laptop to control the device.
3. IR IN: Connect the IR Receiver cable rom the package or receive IR signal rom the
remote control.
4. SERVICE: This is reserved or irmware update use only.
5. DC 5V: Connect with adapter included rom the package and
connect to AC wall outlet or power supply. Once it’s
connected all LEDs on the panel will light up or ew seconds to
represent a success ul connection.
Remote Control
1. POWER: Press Power key to turn on the device or set to
standby mode.
2. OUTPUT 1~ 4 & B1~B4: Press these OUT buttons once
a time to select an input source or an output display.

IR Cable Pin
ssignment
RS-232 Protocol
Wall Plate Remote Controller
Pin Assignment Pin Assignment
1 NC 1 NC
2 TxD 2 RxD
3 RxD 3 TxD
4 NC ► 4 NC
5 GND ◄ 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 19200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit : 1

RS-232 and
Telnet Commands
Command Description
A 1~A 4 Switch output A to 1~4
B 1~B 4 Switch output B to 1~4
IPCONFIG Display the current IP con ig
IPDHCP 0=Set IP mode to static, 1=Set IP mode to DHCP
SIPADDR Set Ethernet IP address
SNETMASK Set Ethernet netmask
SGATEWAY Set Ethernet gateway
HTTPPORT Set http port number
RSTIP IP con iguration reset to actory de aults (DHCP)
IP mode: static, IP address: 192.168.1.50
Netmask: 255.255.255.0, Gateway: 192.168.1.1
Http port: 80, Telnet port: 23
P0 Power o
P1 Power on
ST Displays the current matrix state and irmware
version
? Display all available commands
REBOOT Reboot the unit
FADEFAULT Reset all settings to actory de ault
UPDATE Firmware update
Note: Any commands will be not executed unless followed with a carriage
return. All commands are case-sensitive
Telnet Control
Be ore attempting to use the Telnet control, please ensure that both the Matrix (via the
'LAN /CONTROL' port) and the PC/Laptop are connected to the same active networks.
To access the telnet control in Windows 7, click on ‘Start’ menu and type “cmd” in the
Search ield then press enter.
Under Windows XP go to the ‘Start’ menu and click on “Run”, type “cmd” and press
enter.
Under Mac OS X, go to Go→Application→Utilities→Terminal

Once in the command line inter ace (CLI) type "telnet", then the IP address o the unit and
"23", then hit enter.
This will bring us into the unit which we wish to control. Type "help" to list the available
commands.
Note: Commands will be not executed unless followed by a carriage return.
Commands are case-insensitive. If the IP is changed then the IP Address
required for Telnet access will also change accordingly.

.
Web GUI Control
On a PC/Laptop which is connected to an active network system, open a web browser and
type device’s IP address ( actory de ault static IP: 192.168.1.50) on the web address entry
bar. The browser will display the device’s control page or users to control.
Specifications
Video Bandwidth 600 MHz/6 Gbps
Input Ports 4×HDMI 1×IP Control (RJ-45)
1×IR 1×RS-232 (9-pin D-sub) 1×USB
(Service only)
Output Ports 2×HDMI
Supported Resolutions 480i~1080p@24/50/60
4K2K@24/25/30/50/60 &
VGA~WUXGA
IR Frequency 38 kHz
Baud Rate 19200 bps
Power Supply 5 V/2.6 A DC (US/EU standards
CE/FCC/UL (certified)
ESD Protection Human body model:
±8 kV (air-gap discharge)
±6 kV (contact discharge)
Dimensions 150 mm (W)×162 mm (D)×31 mm (H)
Weight 744 g
Chassis Material Metal
Color Black
Operating Temperature 0˚C~40˚C/32˚F~104˚F
Storage Temperature −20˚C~60˚C/−4˚F~140˚F
Relative Humidity 20~90% RH (non-condensing)

Connection
Diagram

Supported
Resolutions
Resolution Input Output
640×480@60/72/75/85 √ √
720×480@60 √ √
720×576p@50 √ √
800×600@60/72/75/ √ √
1024×768@60/70/75 √ √
1280×720@50/60 √ √
1280×720p@60 √ √
1280×768@60 √ √
1280×800@60 √ √
1280×1024@60 √ √
1360×768@60 √ √
1600×1200@60 √ √
1920×1080i@50 √ √
1920×1080i@60 √ √
1920×1080p@24/25/30/50/60 √ √
1920×1200@60(RB) √ √
3840×2160@24/25/30/50/60 √ √
4096×2160@24/25/30/50/60 √ √