Cornwell Tools CSEPR4TA User manual

CSEPR4TA
4 TON
CSEPR10TA
10 TON
CSEPR4TA/CSEPR10TA 1 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit
Manufactured to comply with the
ASME PASE-2019 Safety Standard
Copyright © Professional Tool Products, 2021
All rights reserved
OPERATING MANUAL •WARNING INFORMATION •PARTS LIST
SPECIFICATIONS
Maximum Capacity ............ 4 Ton @ 7,250 psig ....... 10 Ton @ 7,250 psig
Ram Minimum Height ................... 10.5"...........................................12.7"
Stroke ............................................. 4.7"..............................................5.1"
Fluid Capacity ............................. 12.8 oz. ....................................... 22 oz.
Net Weight .................................. 43 Lbs....................................68.3 Lbs.
Shipping Weight.........................45.2 Lbs. ................................. 71.7 Lbs.
CSEPR4TA CSEPR10TA

CSEPR4TA/CSEPR10TA 2 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the
device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or
not legible, contact Cornwell for replacements. If the operator is not fluent in English, the product and safety instructions shall be read to
and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator
comprehends its contents.
THE NATURE OF HAZARDOUS SITUATIONS
The use of portable automotive supporting devices are subject to certain hazards that cannot be prevented by mechanical means,
but only by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the
use and operation of the equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its
proper use. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads, overloading,
off-centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not designed.
METHODS TO AVOID HAZARDOUS SITUATIONS
• Read, study, understand, and follow all instructions before operating this device.
• The kit owner is responsible for the kit being used in accordance with OSHA, state, and local safety standards.
• User and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.
• Do not use beyond rated capacity.
• When attachments and adapters are used with the kit, the rated capacity of the kit shall be no greater than the rated capacity of the lowest
rated component or combination of components that makes up the kit. Refer to the Owner’s Manual section titled “APPLYING FORCE” for
typical applications and corresponding load capacities.
• Use a pressure gauge that indicates force applied.
• Spreader Ram is rated at 1/2 ton capacity.
• Rubber Heads are rated at 1/2 ton capacity in the 4 ton kit and 1 ton capacity in the 10 ton kit.
• Do not overextend the rams.
• When using extension tubes, position the shortest tube farthest away from the cylinder.
• Attachments and extension tubes must be aligned and fully engaged so the ram force is straight and avoids off-center conditions.
• Before operating, tighten all hose, gauge and manifold connections so they are secure and leak free. Do not over tighten or it may cause
 prematurethreadfailureorsplitpressurettings.Tightenallhosequickdisconnectttingsbyhandonly.
• Do not subject the hose to extreme heat or cold, sharp surfaces, abrasion, impact, kinking, twisting, curling, bending or any condition that
 restrictsoraffectsuidow.
• Make sure setup is stable and secure before performing any work.
• Use this kit for the intended purpose of vehicle body/frame repair only.
• Only components supplied with this kit shall be used with this kit.
• Noalterationsormodicationsshallbemadetoanyofthekitcomponents.
• Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.
WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and birth
defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
Failure to read this manual completely and thoroughly, understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS, MAINTE-
NANCE INSTRUCTIONS and not comply with them, and neglecting the METHODS TO AVOID HAZARDOUS SITUATIONS could cause
accidents resulting in serious or fatal personal injury and/or property damage.
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
WARNING: Indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
WARNING
WARNING
WARNING
WARNING
WARNING INFORMATION

CSEPR4TA/CSEPR10TA 3 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit
PORTABLE HYDRAULIC POWER KIT SETUP INSTRUCTIONS
This is the Safety Alert Symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
SETUP
Please refer to the exploded view drawings on page 7-12 in this manual in order to identify parts:
1. Refer to the parts list and drawing in this manual to identify parts mentioned in this setup procedure.
2. Before installing the force gage (P39) remove the plug A in the hose end of the pump (01). Thread the gage into the gage fitting (P41) and
connect with the receiver (P42) by turning it clockwise. Make sure the connection is tight to prevent leakage.
3. Open the release valve (P29) by turning it counterclockwise until it stops, then pump the handle 4 or 5 full incremented pump strokes to
purge air from the hydraulic system.
4. Install ram (02) or spreader (03) at the end of hose (P30) and secure the quick disconnect fittings together by hand tightening the threaded
sleeve (R06-4T & R15-10T) on the female coupler (R15-4T & R16-10T) to the male coupler (P31) at the end of the hose (P30).
P39
P40
P41
P42
OPERATION
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1. Study the work to be done in order to determine the type ram and other attachments you will be using. Consult the enclosed
chart titled “Applicable force for component set ups” in order to determine the maximum allowable force to be used
in your specific setup. All rams have female hose disconnects attached to them, and the end of the hose has the male quick
disconnect attached to it. Insert the end of the hose (P30) all the way in to the ram’s female quick disconnect (R15). Slide the female
connector’s threaded sleeve (R06-4T & R15-10T) on to the threads at the end of the hose (P30) and hand tighten. Never use any tools
to tighten this connection.
2. Consult this Owner’s Manual section titled APPLICABLE FORCE FOR COMPONENT SET UPS for typical attachment and extension
tube setups and pay very close attention to the corresponding load ratings of certain attachment connections. The use of extension
tubes, ram or plunger toes greatly reduces the hydraulic system’s capacity. When using extension tubes, put the shortest tubes on
the ends of the setup.
3. The pump (1) may be operated in the horizontal or vertical position but the pump (1) must point down when used in the vertical
position.
4. Make sure all hydraulic and attachment connections are fully engaged and tight so ram force is straight in order to avoid off-center
load conditions.
5. During setup, make sure the hose routing avoids kinks, twists, curls or bends that will impede hydraulic fluid flow. Do not use the
hose (P30) as a means to carry the kit components. Do not subject the hose (P30) to any hazards such as fire, extreme heat or cold,
sharp surfaces, or heavy impact. IF A HOSE (P30) RUPTURES, BURSTS, OR NEEDS TO BE DISCONNECTED, IMMEDIATELY SHUT
THE PUMP (1) OFF AND OPEN THE RELEASE VALVE (P29) TO RELEASE HYDRAULIC PRESSURE. NEVER GRASP A LEAKING
PRESSURIZED HOSE, FITTING OR COMPONENT WITH YOUR HANDS OR SUFFER SERIOUS INJURY.
6. Always use the pressure gauge (14) to make sure you are within the required force range when operating the system.
7. In order to pump the ram (2), it will be necessary to turn the release valve knob (P29) in a clockwise direction until tight. Tighten by
hand only.
8. Pumping the handle (P34) up and down transfers the hydraulic fluid from the pump’s reservoir (P6), through the hose (P30), in to the
cylinder and extends the ram with each incremental pump stroke.
9. To release the pressure and return the ram (2) back in to its cylinder (R13-4T & R14-10T) , turn the release valve knob (P29) in a
counterclockwise direction very slowly. Turning the release valve knob (P29) slowly will determine the speed in which the ram (2) will
retract back into its cylinder (R13-4T & R14-10T).
IMPORTANT: The pump includes an overload valve that will activate at the pump’s rated capacity only. If the setup requires a re-
duced rating, the operator is responsible for using the gauge to determine when to stop pumping since the overload valve (P24) is
set to a higher rating.
10. Make sure the ram (2) is completely retracted inside its cylinder (R13-4T & R14-10T) before disconnecting the hose from the cylinder.

CSEPR4TA/CSEPR10TA 4 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit
11. The the hose (P30) and the ram (2) are repeatedly disconnected and exposed to shop or work place floors that are covered with dirt
and debris. It is important to use the dust caps (P32) provided to prevent contaminants from entering the air and hydraulic systems.
12. Based on continuous engagement and disengagement of the hose (P30) from the cylinder (R13-4T & R14-10T), eventually it will
become necessary to add hydraulic fluid to the pump’s reservoir (P6). Completely retract the ram before adding hydraulic fluid. Do
not overfill in order to avoid personal injury and hydraulic malfunction. Use only hydraulic jack oil, Chevron Hydraulic Oil AW ISO 32
or its equivalent Unocal Unax AW 150. Other fluids will cause damage to the hydraulic seals.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the kit in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or any
other harmful elements. The jack must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. Based on continuous engagement and disengagement of the hose from the cylinder, eventually it will become necessary to add hydraulic
fluid to the pump’s reservoir. Completely retract the ram before adding hydraulic fluid. Do not overfill in order to avoid personal injury and
hydraulic malfunction. Use only hydraulic jack oil. Other fluids will cause damage to the hydraulic seals.
Warning: In order to prevent seal damage and kit failure, never use alcohol, hydraulic brake fluid or transmission oil in the pump.
3. Every kit owner is responsible for keeping the kit labels clean and readable. Use a mild soap solution to wash external surfaces of the kit
components but not any moving hydraulic components.
4. Do not attempt to make any hydraulic repairs unless you are a qualified hydraulic repair person that is familiar with this equipment.
Repairs must be performed by an authorized service center.
Spreader Capacity
100% of Ram Capacity 100% of Ram Capacity
100% of Plunger Toe Capacity
25% of Ram Capacity
100% of Rubber Head Capacity
50% of Plunger Toe Capacity
25% of Ram Capacity
6% of Ram Capacity
APPLICABLE FORCE
FOR COMPONENT SET UPS
12% of Ram Capacity

CSEPR4TA/CSEPR10TA 5 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit
TROUBLESHOOTING
Important: If repairs are necessary they must be performed in a dirt-free environment by qualified personnel who are familiar with this
equipment.
INSPECTION
Visual inspection should be made before each use of the engine stand, checking for damaged, loose or missing parts. Each engine stand must be
inspected by a manufacturer’s repair facility immediately, if subjected to an abnormal load or shock. Any stand which appears to be damaged in any
way, is found to be badly worn, or operates abnormally MUST BE REMOVED FROM SERVICE until necessary repairs are made by a manufacturer’s
authorized repair facility. It is recommended that an annual inspection of the stand be made by a manufacturer’s authorized repair facility and that
any defective parts, decals or warning labels be replaced with manufacturer’s specified parts. A list of authorized repair facilities is available from the
manufacturer.
WARRANTY COVERAGE
Cornwell Quality Tools Company (“Cornwell”) warrants this product against defects in material and workmanship for a period of TWO (2)
YEAR from the date of original retail purchase. Subject to the conditions and limitations set forth below, Cornwell will, at its option, either
repair or replace any part of the product(s) that proves defective by reason of improper workmanship or materials.
This warranty does not cover any damage to this product that results from accident, abuse, misuse, natural or personal disaster, or any
unauthorized disassembly, repair, or modification. Repairs, disassembly and modification are only authorized to be made by Cornwell or a
Cornwell Authorized Warranty Center.
PROBLEM ACTION
1. Ram will not lift rated Load. Turn reservoir fill screw (P7) counterclockwise two complete
revolutions and wait 10 seconds. Turn screw clockwise until tight
and proceed to pump. If that does not fix the problem check the
pump reservoir's fluid level. The proper amount of fluid should
be CSEPR4TA - 12.8 ounces and CSEPR10TA - 22 ounces. Use
only hydraulic jack oil. For any other problems contact Cornwell
authorized hydraulic service center.
2. Unit will not sustain rated load or feels “spongy” under rated load. Purge air from hydraulic system as above.
3. Unit will not lift to full height. Purge air from hydraulic system as above.
4. Handle tends to raise up while the unit is under rated load. Pump the handle rapidly several times to push oil past ball
valves in power unit.
5. Unit still does not operate. Contact Cornwell authorized hydraulic service center.

CSEPR4TA/CSEPR10TA 6 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit
WARRANTY SERVICE
In order to have your tool repaired, return the tool to any Cornwell Authorized Warranty Center, freight prepaid. Please include a copy of
your proof of purchase and a brief description of the problem. The tool will be inspected and if any part or parts are found to be defective in
material or workmanship, they will be repaired free of charge, and the repaired tool will be returned to you freight prepaid.
EXCLUSIONS AND LIMITATIONS
THIS WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND
CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. CORNWELL SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING, TO THE EXTENT PERMITTED BY APPLICABLE LAW, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. IF CORNWELL CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY,
ALL SUCH IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
IN NO EVENT SHALL CORNWELL BE LIABLE TO THE PURCHASER OR TO THE USER OF A CORNWELL PRODUCT FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, TORT, OR
ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, WITHOUT LIMITATION, EXPENSES, LOST REVENUES, LOST SAVINGS, LOST
PROFITS, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE PURCHASE, USE OR INABILITY TO USE THE
CORNWELL PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitation on the duration of
implied warranties or conditions, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights that vary by state.
Repair kits and replacement parts are available for many Cornwell products, regardless of whether or not the product is still covered by a
warranty plan.

4 Ton Portable Repair Kit - Parts
CSEPR4TA/CSEPR10TA 7 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit
Item # Part # Description Qty
1 RS4TPANG Pump w/Hose, Neon Green 1
RSHS Hose 1
2 RS4TRNG Ram, Neon Green 1
3 RSSPRANG Spreader, Neon Green 1
4 RS4T01 Case 1
5.1 RS4T02.1NG 3.23"(82mm) Extension, Neon Green 1
5.2 RS4T02.2NG 5.04"(128mm) Extension, Neon Green 1
5.3 RS4T02.3NG 8.50"(216mm) Extension, Neon Green 1
5.4 RS4T02.4NG 16.54"(420mm) Extension, Neon Green 1
5.5 RS4T02.5NG 19.49"(495mm) Extension, Neon Green 1
6 RS4T04ANG Ram Toe, Neon Green 1
Item # Part # Description Qty
7 RS4T05NG Plunger Toe, Neon Green 1
8 RS4T06NG Wedge Head, Neon Green 1
9 RS4T07NG V-Base, Neon Green 1
10 RS4T08 Male Connector 1
11 RS4T09NG Serrated Saddle, Neon Green 1
12 RS4T10 Rubber Head 1
13 RS4T03NG Flat Base, Neon Green 1
14 RSPGA Pressure Gauge Assembly 1
Not
Shown
RSCSEPR4TALK Product Label Kit 1
P39
P40
P41
P42
14

RS4TPANG - 4 Ton Pump
* Items identified by an asterisk are available in pump seal kit, RS4TPSKA.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
P1
P2
P3
P4
P5
P6
P25
P7
P10
P11
P12
P13
P14
P20
P18-1
P18-2
P17
P16
P15
P4
P8
P9
P10
P28
P29
P21
P22
P23
P24
P25
P26
P27
P31
P32
P30
P19
P34
P35
P36 P38
P37
P33
P37
P39
P40
P41
P42
P39
Item # Part # Description Qty
P1 Screw 1
P2 * O-ring 1
P3 RS4TPFNG Pump Foot, Neon Green 1
P4 * O-ring 2
P5 Tie Rod 1
P6 Reservoir 1
P7 Breather Screw 1
P8 Oil Filter 1
P9 Valve Block 1
P10 * Ball 3
P11 * Ball 1
P12 * Spring 1
P13 * Washer 1
P14 Plug Screw 1
P15 * Copper Ring 1
P16 * Piston Seat 1
P17 * Anti-dust Ring 1
P18 * Sealing Ring (incl 18-1 & 18-2) 1
P19 Screw 1
P20 Piston 1
P21 * Ball 1
Item # Part # Description Qty
P22 * Ball Cup 1
P23 * Spring 1
P24 * Screw 1
P25 * O-ring 2
P26 Screw 1
P27 Screw Cap 1
P28 * O-ring 1
P29 RSP15NG Release Valve, Neon Green 1
P30 RSHS Hose 1
P31 RSP17 Male Coupler 1
P32 RSP18 Hose Dust Cover 1
P33 Magnet 1
P34 RS4THNDLNG Handle, Neon Green 1
P35 Handle Sleeve 1
P36 Pin 1
P37 Sealing Ring 2
P38 Pin 1
P39 RSPGA Pressure Gauge (incl P39 - P42) 1
P40 O-ring 1
P41 Gauge Fitting 1
P42 Nut 1
CSEPR4TA/CSEPR10TA 8 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit

RS4TRNG - 4 Ton Ram
RSSPRANG - 4 Ton Spreader
*Items identified by an asterisk are available in Ram Seal Kit, RS4TRSKA.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
Item # Part # Description Qty
R01 RS4TR01 Cover 1
R02 Circlip 1
R03 Piston Rod 1
R04 * Circlip 1
R05 * Bushing 1
R06 Nut 1
R07 * Sealing Ring Set 1
R08 * Retaining Ring 1
R09 Spring 1
R10 Screw 1
R11 RS4TR12 Protection Cap 1
R12 Limit Ring 1
R13 Cylinder 1
R14 Screw 1
R15 Female Coupler 1
R16 O-ring 1
R17 Dust Cover 1
R18 Sealing Ring 1
N/S RSRCPLR Ram Coupler (incl R06,
R15–R18)
1
*Items identified by an asterisk are available in Spreader Seal Kit, RSSPRASK.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
Item # Part # Description Qty
S1 Pin 1
S2 Circlip 1
S3 Movable Jaw 1
S4 Spring 1
S5 Fixed Jaw 1
S6 Piston 1
S7 * Cup Seal 1
S8 * O-ring 1
S9 End Cap 1
S10 Nut 1
S11 Coupler 1
S12 O-ring 1
S13 Dust Cover 1
S14 Sealing ring 1
N/S RSSPRCPLR Spreader Coupler (incl
S10 – S14)
1
CSEPR4TA/CSEPR10TA 9 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit

10 Ton Portable Repair Kit - Parts
Item # Part # Description Qty
01 RS10TPANG Pump w/Hose, Neon Green 1
RSHS Hose 1
02 RS10TRNG Ram, Neon Green 1
03 RSSPRANG Spreader, Neon Green 1
04 RS10T01 Case 1
RS10T01WH Wheel for Case 2
5.1 RS10T02.1NG 3.23"(82mm) Extension, Neon Green 1
5.2 RS10T02.2NG 5.04"(128mm) Extension, Neon Green 1
5.3 RS10T02.3NG 8.50"(216mm) Extension, Neon Green 1
5.4 RS10T02.4NG 16.54"(420mm) Extension, Neon Green 1
06 07 08 09 10 11
05.1
05.2
05.3
05.4
12 13
04
01
02
03
P39
P40
P41
P42
14
Item # Part # Description Qty
06 RS10T04ANG Ram Toe, Neon Green 1
07 RS10T05NG Plunger Toe, Neon Green 1
08 RS10T06NG Wedge Head,Neon Green 1
09 RS10T07NG V-Base, Neon Green 1
10 RS10T08 Male Connector 1
11 RS10T09NG Serrated Saddle, Neon Green 1
12 RS10T10 Rubber Head 1
13 RS10T03NG Flat Base, Neon Green 1
14 RSPGA Pressure Gauge Assembly 1
N/S RSCSEPR10TALK Product Label Kit 1
CSEPR4TA/CSEPR10TA 10 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit

RS10TPANG - 10 Ton Pump
*Items identified by an asterisk are available in pump seal kit, RS10TPSKA.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
Item # Part # Description Qty
P1 Screw 1
P2 * O-ring 1
P3 RS10TPFNG Pump Foot, Neon Green 1
P4 * O-ring 2
P5 Tie Rod 1
P6 Reservoir 1
P7 Breather Screw 1
P8 Oil Filter 1
P9 Valve Block 1
P10 * Ball 3
P11 * Ball 1
P12 * Spring 1
P13 * Washer 1
P14 Plug Screw 1
P15 * Copper Ring 1
P16 * Piston Seat 1
P17 * Anti-dust Ring 1
P18 * Sealing Ring (incl 18-1 & 18-2) 1
P19 Screw 1
P20 Piston 1
P21 * Ball 1
Item # Part # Description Qty
P22 * Ball Cup 1
P23 * Spring 1
P24 * Screw 1
P25 * O-ring 2
P26 Screw 1
P27 Screw Cap 1
P28 * O-ring 1
P29 RSP15NG Release Valve, Neon Green 1
P30 RSHS Hose 1
P31 RSP17 Male Coupler 1
P32 RSP18 Hose Dust Cover 1
P33 Magnet 1
P34 RS10THNDLNG Handle, Neon Green 1
P35 Handle Sleeve 1
P36 Pin 1
P37 Sealing Ring 2
P38 Pin 1
P39 RSPGA Pressure Gauge (incl P39 - P42) 1
P40 O-ring 1
P41 Gauge Fitting 1
P42 Nut 1
P1
P2
P3
P4
P5
P6
P25
P7
P10
P11
P12
P13
P14
P20
P18-1
P18-2
P17
P16
P15
P4
P8
P9
P10
P28
P29
P21
P22
P23
P24
P25
P26
P27
P31
P32
P30
P19
P34
P35
P36 P38
P37
P33
P37
P39
P40
P41
P42
P39
CSEPR4TA/CSEPR10TA 11 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit

RS10TRNG - 10 Ton Ram
RSSPRANG - 10 Ton Spreader
*Items identified by an asterisk are available in Ram Seal Kit, RS10TRSKA.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
*Items identified by an asterisk are available in Spreader Seal Kit, RSSPRASK.
NOTE: Items which are not identified by a part number or with an asterisk are not available separately.
Item# Part# Description Qty
R01 RS10TR01 Cover 1
R02 Circlip 1
R03 Piston Rod 1
R04 * Circlip 1
R05 * Bushing 1
R06 * Sealing Ring Set 1
R07 Pin 1
R08 * Circlip 1
R09 Nut 1
R10 Spring 1
R11 RS10TR12 Screw 1
R12 Protection Cap 1
R13 Limit Ring 1
R14 Cylinder 1
R15 Nut 1
R16 Female Coupler 1
R17 O-ring 1
R18 Dust Cap 1
R19 Sealing Ring 1
N/S RSRCPLR Ram Coupler (incl R15–R19) 1
Item# Part# Description Qty
S1 Pin 1
S2 Circlip 1
S3 Movable Jaw 1
S4 Spring 1
S5 Fixed Jaw 1
S6 Piston 1
S7 * Cup Seal 1
S8 * O-ring 1
S9 End Cap 1
S10 Nut 1
S11 Coupler 1
S12 O-ring 1
S13 Dust Cover 1
S14 Sealing ring 1
N/S RSSPRCPLR
Spreader Coupler (incl S10 – S14) 1
CSEPR4TA/CSEPR10TA 12 03/18/21
CSEPR4TA AND CSEPR10TA
4 Ton and 10 Ton Portable
Repair Kit