Cornwell Tools CSEPR4T User manual

CSEPR4T
4 TON
CSEPR10T
10 TON
CSEPR4T/CSEPR10T 1 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit
Manufactured to comply with the
ASME PASE-2019 Safety Standard
Copyright © Professional Tool Products, 2020
All rights reserved
OPERATING MANUAL •WARNING INFORMATION •PARTS LIST
SPECIFICATIONS
Maximum Capacity ............ 4 Ton @ 7,250 psig ....... 10 Ton @ 7,250 psig
Ram Minimum Height ................... 10.5"...........................................12.7"
Stroke ............................................. 4.7"..............................................5.1"
Fluid Capacity ............................. 10.5 oz. .....................................17. 5 oz.
Net Weight .................................. 43 Lbs....................................68.3 Lbs.
Shipping Weight.........................45.2 Lbs. ................................. 71.7 Lbs.
CSEPR4T CSEPR10T

CSEPR4T/CSEPR10T 2 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit
IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING
BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.
It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the
device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or
not legible, contact Cornwell for replacements. If the operator is not fluent in English, the product and safety instructions shall be read to
and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator
comprehends its contents.
THE NATURE OF HAZARDOUS SITUATIONS
The use of portable automotive supporting devices are subject to certain hazards that cannot be prevented by mechanical means,
but only by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the
use and operation of the equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its
proper use. Examples of hazards are dropping, tipping or slipping of loads caused primarily by improperly securing loads, overloading,
off-centered loads, use on other than hard level surfaces, and using equipment for a purpose for which it was not designed.
METHODS TO AVOID HAZARDOUS SITUATIONS
• Read, study, understand and follow all instructions before operating this device.
• The kit owner is responsible for the kit being used in accordance with OSHA, state, and local safety standards.
• Wear eye protection that meets ANSI Z87.1 and OSHA standards, users and bystanders.
• Do not use kit beyond its rated capacity.
• When attachments and adapters are used with the kit, the rated capacity of the kit shall be no greater than the rated capacity of
the lowest rated component or combination of components that makes up the kit. Please refer to the Owner’s Manual section titled
APPLICABLE FORCE FOR COMPONENT SETUPS. Use a pressure gauge that indicates force applied. Wedge Rams are rated at
1-ton capacity. Rubber Heads are rated at 1/2-ton capacity in the 4-ton kit and 1-ton capacity in the 10-ton kit.
• Do not overextend the rams.
• When using extension tubes, position the shortest tube farthest away from the cylinder.
• Attachments and extension tubes must be aligned and fully engaged so the ram force is straight and avoids off-center conditions.
• Before operating, tighten all hose, gauge and manifold connections so they are secure and leak free. Do not over tighten or it may
cause premature thread failure or split pressure fittings. Tighten all hose quick disconnect fittings by hand only.
• Do not subject the hose to extreme heat or cold, sharp surfaces, abrasion, impact, kinking, twisting, curling, bending or any
condition that restricts or affects fluid flow.
• Make sure setup is stable and secure before performing any work.
• Use this kit for the intended purpose of vehicle body/frame repair only.
• Only components supplied with this kit shall be used with this kit.
• No alterations or modifications shall be made to any of the kit components.
• Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.
WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and
birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS
Failure to read this manual completely and thoroughly, understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and not comply with them, and neglecting the METHODS TO AVOID HAZARDOUS SITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
WARNING: Indicates a hazardous situation
which, if not avoided, could result in death
or serious injury.
WARNING
WARNING
WARNING
WARNING
WARNING INFORMATION

CSEPR4T/CSEPR10T 3 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit
SETUP
Please refer to the exploded view drawings on page 6-11 in this manual in order to identify parts:
1. Remove the hose from the pump. Remove any pipe dope tape from the pump. Put 2 layers of pipe dope tape around the threads of the
adapter, around the threads of the hose, and around the threads of the gauge. Thread the adapter in the pump until tight with the gauge
port sticking straight up. Tighten the hose in the end of the adapter. Tighten the gauge in the adapter with the face of the gauge pointing
toward the pump handle.
2. Install the ram at the end of the hose and secure the quick disconnect fittings together by hand tightening the threaded sleeve on the
ram fitting.
3. Insert the pump handle in the pump linkage receiver and rotate the handle clockwise until tight. Before operating the pump, turn the
reservoir vent screw in a counterclockwise direction until it stops.
4. During shipping or handling air may have become trapped in the hydraulic system. If the pump is not providing a full incremental pump
stroke or the ram feels spongy, it will be necessary to purge the air out of the hydraulic system:
a. Before operating the pump, turn the reservoir vent screw in a counterclockwise direction until it stops.
b. Place the pump horizontally on a table. Position the hose and ram over the edge of the table, lower than the pump with the ram piston
pointing down.
c. Close the pump’s release valve and pump the ram to its complete or its furthest extension. Open the pump’s release valve to retract
the ram all the way. Conduct this procedure several times without a load.
d. Repeat steps “b” and “c” until all air is purged from the system.
OPERATION
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1. Study the work to be done in order to determine the type ram and other attachments you will be using. Consult the enclosed chart titled
“Applicable force for component set ups” in order to determine the maximum allowable force to be used in your specific setup. All rams
have female hose disconnects attached to them, and the end of the hose has the male quick disconnect attached to it. Insert the male
quick disconnect at the end of the hose all the way in to the ram’s female quick disconnect. Slide the female connector’s threaded sleeve
on to the threads of the male connector and hand tighten. Never use any tools to tighten this connection.
2. Consult this Owner’s Manual section titled APPLICABLE FORCE FOR COMPONENT SET UPS for typical attachment and extension tube
setups and pay very close attention to the corresponding load ratings of certain attachment connections. The use of extension tubes,
ram or plunger toes greatly reduces the hydraulic system’s capacity. When using extension tubes, put the shortest tubes on the ends
of the setup.
3. The pump may be operated in the horizontal or vertical position but the pump must point down when used in the vertical position.
4. Make sure all hydraulic and attachment connections are fully engaged and tight so ram force is straight in order to avoid off-center
load conditions.
5. During setup, make sure the hose routing avoids kinks, twists, curls or bends that will impede hydraulic fluid flow. Do not use the hose
as a means to carry the kit components. Do not subject the hose to any hazards such as fire, extreme heat or cold, sharp surfaces, or
heavy impact. WARNING: Risk of fluid injection injury. NEVER GRASP LEAKING PRESSURIZED HOSE, FITTING OR COMPONENT,
OR EXPOSE BODY PARTS TO PRESSURIZED FLUID. SEVERE PERSONAL INJURY MAY RESULT.
6. Always use the force gauge to make sure you are within the required force range when operating the system.
7. In order to pump the ram it will be necessary to turn the release valve knob in a clockwise direction until tight. Tighten by hand only.
8. Pumping the handle up and down transfers the hydraulic fluid from the pump’s reservoir, through the hose, in to the cylinder and extends
the ram with each incremental pump stroke.
9. To release the pressure and return the ram back in to its cylinder, turn the release valve knob in a counterclockwise direction very slowly.
Turning the release valve knob slowly will determine the speed in which the ram will retract back into its cylinder.
IMPORTANT: The pump includes an overload valve that will activate at the pump’s rated capacity only. If the setup requires a reduced
rating, the operator is responsible for using the gauge to determine when to stop pumping since the overload valve is set to a higher
rating.
10. Make sure the ram is completely retracted inside its cylinder before disconnecting the hose from the cylinder.
11. The air and hydraulic quick disconnect fittings are repeatedly disconnected and exposed to shop or work place floors that are covered
with dirt and debris. It is important to use the dust caps provided to prevent contaminants from entering the hydraulic systems.
12. Based on continuous engagement and disengagement of the hose from the cylinder, eventually it will become necessary to add
hydraulic fluid to the pump’s reservoir. Completely retract the ram before adding hydraulic fluid. Do not overfill in order to avoid personal
injury and hydraulic malfunction. Use only hydraulic jack oil. Other fluids will cause damage to the hydraulic seals.

CSEPR4T/CSEPR10T 4 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the kit in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or any
other harmful elements. The jack must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2. Based on continuous engagement and disengagement of the hose from the cylinder, eventually it will become necessary to add hydraulic
fluid to the pump’s reservoir. Completely retract the ram before adding hydraulic fluid. Do not overfill in order to avoid personal injury and
hydraulic malfunction. Use only hydraulic jack oil. Other fluids will cause damage to the hydraulic seals.
Warning: In order to prevent seal damage and kit failure, never use alcohol, hydraulic brake fluid or transmission oil in the pump.
3. Every kit owner is responsible for keeping the kit labels clean and readable. Use a mild soap solution to wash external surfaces of the kit
components but not any moving hydraulic components.
4. Do not attempt to make any hydraulic repairs unless you are a qualified hydraulic repair person that is familiar with this equipment.
Repairs must be performed by an authorized service center.
TROUBLESHOOTING
Important: If repairs are necessary they must be performed in a dirt-free environment by qualified personnel who are familiar with this
equipment.
INSPECTION
Visual inspection should be made before each use of the engine stand, checking for damaged, loose or missing parts. Each engine stand must be
inspected by a manufacturer’s repair facility immediately, if subjected to an abnormal load or shock. Any stand which appears to be damaged in any
way, is found to be badly worn, or operates abnormally MUST BE REMOVED FROM SERVICE until necessary repairs are made by a manufacturer’s
authorized repair facility. It is recommended that an annual inspection of the stand be made by a manufacturer’s authorized repair facility and that
any defective parts, decals or warning labels be replaced with manufacturer’s specified parts. A list of authorized repair facilities is available from the
manufacturer.
PROBLEM ACTION
1. Unit will not lift rated load. Purge air from hydraulic system by following procedure under
SETUP.
2. Unit will not sustain rated load or feels “spongy” under rated load. Purge air from hydraulic system as above.
3. Unit will not lift to full height. Purge air from hydraulic system as above.
4. Handle tends to raise up while the unit is under rated load. Pump the handle rapidly several times to push oil past ball
valves in power unit.
5. Unit still does not operate. Contact Cornwell authorized hydraulic service center.

CSEPR4T/CSEPR10T 5 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit
WARRANTY COVERAGE
Cornwell Quality Tools Company (“Cornwell”) warrants this product against defects in material and workmanship for a period of TWO (2)
YEAR from the date of original retail purchase. Subject to the conditions and limitations set forth below, Cornwell will, at its option, either
repair or replace any part of the product(s) that proves defective by reason of improper workmanship or materials.
This warranty does not cover any damage to this product that results from accident, abuse, misuse, natural or personal disaster, or any
unauthorized disassembly, repair, or modification. Repairs, disassembly and modification are only authorized to be made by Cornwell or a
Cornwell Authorized Warranty Center.
WARRANTY SERVICE
In order to have your tool repaired, return the tool to any Cornwell Authorized Warranty Center, freight prepaid. Please include a copy of
your proof of purchase and a brief description of the problem. The tool will be inspected and if any part or parts are found to be defective in
material or workmanship, they will be repaired free of charge, and the repaired tool will be returned to you freight prepaid.
EXCLUSIONS AND LIMITATIONS
THIS WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND
CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. CORNWELL SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED
WARRANTIES, INCLUDING, TO THE EXTENT PERMITTED BY APPLICABLE LAW, ANY WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. IF CORNWELL CANNOT LAWFULLY DISCLAIM IMPLIED WARRANTIES UNDER THIS LIMITED WARRANTY,
ALL SUCH IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
IN NO EVENT SHALL CORNWELL BE LIABLE TO THE PURCHASER OR TO THE USER OF A CORNWELL PRODUCT FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, TORT, OR
ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, WITHOUT LIMITATION, EXPENSES, LOST REVENUES, LOST SAVINGS, LOST
PROFITS, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE PURCHASE, USE OR INABILITY TO USE THE
CORNWELL PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages or exclusions or limitation on the duration of
implied warranties or conditions, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights that vary by state.
Repair kits and replacement parts are available for many Cornwell products, regardless of whether or not the product is still covered by a
warranty plan.

13
2
2A
5.1
5.2
5.3
5.4
5.5
7 8 9 10 11 12 13 146
4
4 Ton Portable Repair Kit - Parts
Only items identified by part number are available for purchase.
CSEPR4T/CSEPR10T 6 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit
1 RS4TPNG Pump (incl. hose) - Neon Green 1
2 RS4TRNG Ram - Neon Green 1
2A RSHS Hose 1
3 RSSPRNG Spreader - Neon Green 1
4 RS4T01 Case 1
5.1 RS4T02.1NG 3.23"Extension - Neon Green 1
5.2 RS4T02.2NG 5.04"Extension - Neon Green 1
5.3 RS4T02.3NG 8.50"Extension - Neon Green 1
5.4 RS4T02.4NG 16.54"Extension - Neon Green 1
5.5 RS4T02.5NG 19.49"Extension - Neon Green 1
Item Part
No. No. Description Qty.
Item Part
No. No. Description Qty.
6 RS4T04ANG Ram Toe - Neon Green 1
7 RS4T05NG Plunger Toe - Neon Green 1
8 RS4T06NG Wedge Head - Neon Green 1
9 RS4T07NG V-Base - Neon Green 1
10 RS4T08 Male Connector 1
11 RS4T09NG Serrated Saddle - Neon Green 1
12 RS4T10 Rubber Head 1
13 RS4T03NG Flat Base - Neon Green 1
14 RSPG Pressure Gauge 1
RSCSEPR4TPLK Product Label Kit (not shown) 1

P1 Screw 1
P2 * O-Ring 1
P3 RSP12NG Back Cover - Neon Green 1
P4 Nylon Ring 1
P5 RSP09A Oil Filler Assembly (incl. #4) 1
P6 * O-Ring 2
P7 Tie Rod 1
P8 Reservoir 1
P9 Oil Filter 1
P10 Pump 1
P11 * Steel Ball 1
P12 * Spring 1
P13 * O-Ring 2
P14 Screw 1
P15 * Nylon Ring 1
P16 * Valve Base 1
P17 * Steel Ball 2
P18 Valve Cover 1
P19 * Nylon Ring 1
P20 * Sealing Ring 1
P21 * Washer 1
P22 * O-Ring 1
P23 * Washer 1
P24 Piston Base 1
P25 * O-Ring 1
P26 * Washer 1
Item Part
No. No. Description Qty.
Item Part
No. No. Description Qty.
P27 Piston 1
P28 * Steel Ball 1
P29 Ball Cap 1
P30 * Spring 1
P31 Screw 1
P32 Screw 1
P33 Screw Protector 1
P34 * O-Ring 1
P35 RSP15NG Release Valve - Neon Green 1
P36 Adapter 1
P37 Nut 1
P38 Gauge Adapter 1
P38A RSPGAA Gauge Adapter Assembly 1
(incl. #P36-P40)
P39 O-Ring 1
P40 Plunger 1
P41 RSPG Pressure Gauge 1
P42 RSHS Hydraulic Hose 1
P43 RSP17 Coupler 1
P44 RSP18 Hose Dust Cover 1
P45 Pin 1
P46 Retaining Ring 1
P47 Pin 1
P48 Handle Socket 1
P49 RS4TP41NG Handle (incl. #P50) - Neon Green 1
P50 Handle Sleeve 1
Only items identified by part number are available for purchase.
* Items identified by an asterisk are available in Pump Seal Kit, RSPSKA.
P1
P2
P3
P4
P5
P6
P7
P8
P6
P10
P9
P35
P34
P17
P36
P37
P38
P39
P40
P38A
P41
P42
P43
P44
P28
P29
P30
P31
P13
P32
P33
P14
P27
P26
P25
P24
P23
P22
P21
P20
P19
P18
P17
P16
P15
P13
P12
P11
P45
P46
P47
P48
P46
P49
P50
4 Ton Pump - Parts
CSEPR4T/CSEPR10T 7 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit

R01 RS4TR01 Cover 1
R02 Circlip 1
R03 Piston Rod 1
R04 * Circlip 1
R05 * Bushing 1
R06 * Nylon Ring 1
R07 * Sealing Ring 1
R08 * Circlip 1
R09 Spring 1
R10 Screw 1
R11 RS4TR12 Protection Cap 1
R12 Ring for Ram 1
R13 Cylinder 1
R14 Screw 1
RSCPRA Coupler 1
(incl. #S10, S11, P11, S12, S13)
S1 Pin 1
S2 Circlip 2
S3 Movable Jaw 1
S4 Spring 1
S5 Fixed Jaw 1
S6 Piston 1
S7 * Cup Seal 1
S8 * O-Ring 1
S9 End Cap 1
RSCPRA Coupler
(incl. #S10, S11, P11, S12, S13) 1
Item Part
No. No. Description Qty.
Item Part
No. No. Description Qty.
Only items identified by part number are available for purchase.
* Items identified by an asterisk are available in Ram Seal Kit, RS4TRSKA.
Only items identified by part number are available for purchase.
* Items identified by an asterisk are available in Spreader Seal Kit, RSSPRSK.
R11
R09
R01
R02
R03
R04
R05
R06
R07
R08
R10
R12
R13
R14
S10
S11
P11
S12
S13
S4
S2
S1
S3
S5
S2
S6
S7
S8
S9
S10
S11
P11
S12
S13
4 Ton Ram - Parts
4 Ton Spreader - Parts
CSEPR4T/CSEPR10T 8 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit

1 RS10TPNG Pump (incl. hose) - Neon Green 1
2 RS10TRNG Ram - Neon Green 1
2A RSHS Hose 1
3 RSSPRNG Spreader - Neon Green 1
4 RS10T01 Case 1
RS10T01WH Wheel with Hardware for Case 2
5.1 RS10T02.1NG 4.33"Extension - Neon Green 1
5.2 RS10T02.2NG 10.43"Extension - Neon Green 1
5.3 RS10T02.3NG 14.37"Extension - Neon Green 1
5.4 RS10T02.4NG 20.47"Extension - Neon Green 1
Item Part
No. No. Description Qty.
Item Part
No. No. Description Qty.
6 RS10T04ANG Ram Toe - Neon Green 1
7 RS10T05NG Plunger Toe - Neon Green 1
8 RS10T06NG Wedge Head - Neon Green 1
9 RS10T07NG V-Base - Neon Green 1
10 RS10T08 Male Connector 1
11 RS10T09NG Serrated Saddle - Neon Green 1
12 RS10T10 Rubber Head 1
13 RS10T03NG Flat Base - Neon Green 1
14 RSPG Pressure Gauge 1
RSCSEPR10TPLK Product Label Kit (not shown) 1
Only items identified by part number are available for purchase.
13
2
2A 5.1
5.2
5.3
5.4
7 8 9 10 11 12 13 146
4
10 Ton Portable Repair Kit - Parts
CSEPR4T/CSEPR10T 9 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit

P1 Screw 1
P2 * O-Ring 1
P3 RSP12NG Back Cover - Neon Green 1
P4 Nylon Ring 1
P5 RSP09A Oil Filler Assembly (incl. #P4) 1
P6 * O-Ring 2
P7 Tie Rod 1
P8 Reservoir 1
P9 Oil Filter 1
P10 Pump 1
P11 * Steel Ball 1
P12 * Spring 1
P13 * O-Ring 2
P14 Screw 1
P15 * Nylon Ring 1
P16 * Valve Base 1
P17 * Steel Ball 2
P18 Valve Cover 1
P19 * Nylon Ring 1
P20 * Sealing Ring 1
P21 * Washer 1
P22 * O-Ring 1
P23 * Washer 1
P24 Piston Base 1
P25 * O-Ring 1
P26 * Washer 1
Item Part
No. No. Description Qty.
Item Part
No. No. Description Qty.
P27 Piston 1
P28 * Steel Ball 1
P29 Ball Cap 1
P30 * Spring 1
P31 Screw 1
P32 Screw 1
P33 Screw Protector 1
P34 * O-Ring 1
P35 RSP15NG Release Valve - Neon Green 1
P36 Adapter 1
P37 Nut 1
P38 Gauge Adapter 1
P38A RSPGAA Gauge Adapter Assembly 1
(incl. #P36-P40)
P39 O-Ring 1
P40 Plunger 1
P41 RSPG Pressure Gauge 1
P42 RSHS Hydraulic Hose 1
P43 RSP17 Coupler 1
P44 RSP18 Hose Dust Cover 1
P45 Pin 1
P46 Retaining Ring 1
P47 Pin 1
P48 Handle Socket 1
P49 RS10TP41NG Handle (incl. #50) - Neon Green 1
P50 Handle Sleeve 1
Only items identified by part number are available for purchase.
* Items identified by an asterisk are available in Pump Seal Kit, RSPSKA.
P1
P2
P3
P4
P5
P6
P7
P8
P6
P10
P9
P35
P34
P17
P36
P37
P38
P39
P40
P41
P42
P43
P44
P28
P29
P30
P31
P13
P32
P33
P14
P27
P26
P25
P24
P23
P22
P21
P20
P19
P18
P17
P16
P15
P13
P12
P11
P45
P46
P47
P48
P46
P49
P50
P38A
10 Ton Pump - Parts
CSEPR4T/CSEPR10T 10 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit

R01 RS10TR01 Cover 1
R02 Circlip 1
R03 Piston Rod 1
R04 * Circlip 1
R05 * Bushing 1
R06 * Nylon Ring 1
R07 * Sealing Ring 1
R08 * Circlip 1
R09 Nut 1
R10 Spring 1
R11 Screw 1
R12 RS10TR12 Protection Cap 1
R13 Ring for Ram 1
R14 Cylinder 1
R15 Screw 1
RSCPRA Coupler
(incl. #S10, S11, P11, S12, S13) 1
S1 Pin 1
S2 Circlip 2
S3 Movable Jaw 1
S4 Spring 1
S5 Fixed Jaw 1
S6 Piston 1
S7 * Cup Seal 1
S8 * O-Ring 1
S9 End Cap 1
RSCPRA Coupler
(incl. #S10, S11, P11, S12, S13) 1
Item Part
No. No. Description Qty.
Item Part
No. No. Description Qty.
Only items identified by part number are available for purchase.
* Items identified by an asterisk are available in Ram Seal Kit, RS10TRSKA.
Only items identified by part number are available for purchase.
* Items identified by an asterisk are available in Spreader Seal Kit, RSSPRSK.
S4
S2
S1
S3
S5
S2
S6
S7
S8
S9
S10
S11
P11
S12
S13
R01
R02
R03
R04
R05
R06
R07
R08
R09
R10
R11
R12
R13
R14
R15
S10
S11
P11
S12
S13
10 Ton Ram - Parts
10 Ton Spreader - Parts
CSEPR4T/CSEPR10T 11 03/31/20
CSEPR4T AND CSEPR10T
4 Ton and 10 Ton Portable
Repair Kit