Courtyard Creations TGS38SW-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
TGS38SW-WM
Do not sit or stand on this table.
Do not discard any of the packaging until you have checked that you have all the parts and pack
of fittings.
Keep children away during assembly. This item contains small parts which can be swallowed by
children. Children should always be under direct adult supervision while using the product.
Retain the assembly instructions for future reference.
Please quote following FQC NO. when contacting service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
PAGE 1 OF 2 COURTYARD CREATIONS INC.
!
!
!
!
!
STOP DON’T RETURN TO STORE!
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
1 1
2
3
4
5
6
7
8
4 4
4
1
4
1
4
TGS38SW-CS01
TGS38SW-CS02
62TGS38SWY101
17C17A0403001Y4
17C33A0709001Y4
17FA05040301-Y4
1800337004
17KAA0101----Y4
TABLE TOP
LEG
CENTER CONNECTOR
SCREW ST4.2*12
BOLT M6*25
WASHER d6.5*D13*1.0
BOLT CAP
HEX.KEY WRENCH 4MM
FIGURE 1
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Part #8)
Step 1:
Place the table top (#1) onto a non-abrasive
surface, such as a carpet, with its underside
facing up. Insert the legs (#2) into the plastic
holders on the table top (#1) rim. Fasten them
together by using screws (#4). See Figure 1.
1
2
2
2
2
4

Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free
TEL: [phone]
FAX: [phone]
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
SHOULD YOU NOTLOCATE ALL OF THE ABOVE PARTS, PLEASE INSPECTALL
PACKING MATERIAL FOR ANY SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED IN SHIPMENT.
SHOULD YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTIS MISSING OR DAMAGED,PLEASE CALL THE HELP LINE 1-877-539-7436
BEFORERETURNING THE ITEM TO THE STORE.
PLEASE PROVIDE THEFOLLOWING INFORMATION:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
SHOWN ON ASSEMBLY INSTRUCTIONS.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
PAGE 2 OF 2
STOP DON’T RETURN TO STORE!
FIGURE 2
FIGURE 3
Step 2:
Fasten the center connector (#3) to the middle
of the legs (#2) by using bolts (#5) and washers
(#6). Make sure that all of the bolts have been
tightened completely, and then cover them with
bolt caps (#7). See Figure 2.
NOTE:
The arrow mark on the center connector (#3) must
coincide with figure 2 to ensure proper assembly.
Step 3:
Turn the table to its upright position. See Figure 3.
Cleaning and Maintenance
•Wash frame parts with mild soap and water,
rinse thoroughly, and dry frame completely.
Do not use bleach, acid, or other solvents on
the frame parts.
•Wash glass with mild soap and water, rinse
thoroughly, and dry glass completely.
•Please inspect and tighten all bolts and
fasteners on a regular basis to ensure proper
performance and safety of your table.
•When moving the table, do not drag.
•We recommend the use of furniture covers
when not in use.
•In order to prolong the life and beauty of your
table, we recommend it be stored in a dry and
protected area during off season periods.
2
2
5
6
7
2
2
3