Courtyard Creations KLS132S-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
KLS132S-WM
PAGE 1 OF 2 COURTYARD CREATIONS INC.
STOP DON’T RETURN TO STORE!
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings
required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
!
!
!
!
!
PARTS LIST
PART
NO. PART Q’TY
1 1
1
1
2
12
8
1
2
3
4
5
6
7
12
11
10
9
2
8
2
1
1
MATERIAL CODE PART
NO. PART Q’TYMATERIAL CODE
LEFT LEG
RIGHT LEG
BOLT M6*16
BOLT M6*35
PLASTIC NUT M6*P1.0
BOLT CAP
BOLT CAP M6
NUT WRENCH 10&13MM
HEX.KEY WRENCH 4MM
BACK ASSEMBLY
SEAT ASSEMBLY
KLS132S-CS01
KLS132S-CS02
KLS132S-CS03
KLS132S-CS04
17C33A0706001Y4
17C01A0712001Y4
8
WASHER d6.5*D13*1.0
17FA05040301-Y4
18000C23001
18000337004
18000337001
17KAA0101----Y4
17KAB1101----Y4
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
Step 1:
Place the right leg (#4) onto a non-abrasive surface,
such as a carpet, with its holes facing upwards. At the
rear, fasten the seat assembly (#2) to legs (#3 and #4)
by using bolts (#5) and washers (#7). Keep the bolts
loose. See Figure 1.
Note:
The labels marked “L” and “R” on legs (#3 and #4)
should coincide with Figure 1 to ensure proper
assembly.
FIGURE 1
16
3
2
5
7
9
5
7
9
#5 BOLT M6*16
L
4R

6
2
7
7
8
10
Step 3:
Fasten the back assembly (#1) to the seat assembly
(#2) by using bolts (#6), washers (#7), and plastic nuts
(#8). Make sure that all of the bolts have been tightened
completely and cover them with bolt caps (#9 and #10).
See Figure 3.
Step 4:
Turn the lounge to its upright position. See Figure 4.
FIGURE 3
FIGURE 4
35
#6 BOLT M6*35
Step 2:
At the front, fasten the seat assembly (#2) to legs (#3
and #4) by using bolts (#5) and washers (#7). Keep the
bolts loose. See Figure 2.
FIGURE 2
57
9
5
7
9
16
#5 BOLT M6*16
3
2
4
Cleaning and Maintenance
•Wash frame parts with mild soap and water, rinse
thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame parts.
•We recommend the use of furniture covers when not
in use.
•Inspect and tight en all bolts and fasteners on a regular
basis t o ensure the proper performance and safety of
your lounge.
•In order to prolong the life and beauty of your lounge,
we recommend that it be stored in a dry and protected
area during off season periods.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
1
STOP DON’T RETURN TO STORE!
PAGE 2 OF 2