Courtyard Creations RUS426K-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PAGE 1 OF 7
RUS426K-WM
Use the correct bolts as indicated. Do not tighten any of the bolts until the swing is completely
assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
COURTYARD CREATIONS INC.
!
!
!
!
!
STOP DON’T RETURN TO STORE!
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]

A. Read the instructions thoroughly. Acquaint yourself with the inventory of parts
and the accompanying drawings to ensure safe and proper assembly.
B. You will need the following tools:
- Phillips Screwdriver
- Nut Wrench (See Part #35)
- Hex. Key Wrench (See Part #34)
C. Lay out all of the parts and identify them using the table below.
PAGE 2 OF 7
PARTS LIST
PART
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
2
4
1
1
1
2
4
28
7
4
28
12
6
2
4
1
12
2
2
2
2
1
2
1
2
4
5
6
1
1
1
2
1
1
4
RUS426K-CS09-8
17C01A0716072Y4
17C01A0714003Y4
17C01A0821061Y4
17FA08060601-Y4
17FA05050401-Y4
18060616261601
18000C06001
17D03A040401-Y4
18000C23001
18000337005
18000337002
18000319005
18000615004
2820072014001
18000018001
17KAA0204----Y4
17KAB1201----Y4
61R426KD00001BA
WASHER d8.5*D17*1.6
WASHER d6.5*D16*1.2
WASHER d8.5*D16*18
BOLT M6*45
BOLT M8*60
BOLT M6*40
CANOPY/FRAME CONNECTOR
LEG CAP
PLASTIC SCREW
HEX.KEY WRENCH 6MM
NUT WRENCH 13&17MM
CANOPY
62RUS426KI102
62RUS426KH102
62RUS426KN102
62RUS426KN101
62RUS426KI101
62RUS4040H102
RUS426K-CS11-3
RUS426K-CS11-4
62RUS426KH101
62RUS426KH104
RUS426K-CS01-2
RUS426K-CS01-3
62RUS426KM101
17GA20405201-Y3
17C17A1306001Y4
17C01A0835011Y4
17C01A0721091Y4
TOP CROSS BEAM W/ADJUSTABLE TEETH
REAR CROSS BRACE
LATERAL CROSS BRACE
FRONT UPRIGHT SUPPORT
REAR UPRIGHT SUPPORT
SWING ARM TUBE
FRONT/REAR CANOPY BRACE
U-SHAPED SIDE CANOPY BRACE
LEFT SEAT ASSEMBLY
RIGHT SEAT ASSEMBLY
FRONT SUPPORT BRACE
BACK SUPPORT BRACE
SWING ARM LEFT
SWING ARM RIGHT
SUSPENSION SPRING
SCREW ST4.2*16
BOLT M8*105
BOLT M6*60
MATERIAL
CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
STOP DON’T RETURN TO STORE!
PLASTIC NUT M8*P1.25
NUT M8*1.25
PLASTIC NUT M6*P1.0
PLASTIC CAP M6
BOLT CAP M8
BOLT CAP M6

Step 5:
Slide the canopy/frame connectors (#31) onto
the U-shaped side canopy braces (#7) and
fasten into position by using screws (#16).
Make sure that the teeth on the canopy
connectors are facing towards the inside of the
swing. See Fig. B – Step 1 and Step 2.
PAGE 3 OF 7
Fig. A
Fig. B
Note:
When fastening with bolts and nuts, always use
a washer (#22 and #23) between the tube and
the bolt and the tube and the nut.
Step 1:
Fasten the front and rear upright support (#2
and #3) at the top, by using bolts (#17),
washers (#22), and plastic nuts (#25). Repeat
the same procedure for both sides. Do not fully
tighten the plastic nuts and bolts yet.
See Fig. A – Step 1.
Step 2:
Attach the top cross beam w/adjustable teeth
(#1) to both ends of the upright supports (#2
and #3). See Fig. A – Step 2.
Step 3:
Fasten the lateral cross braces (#4) to the
uprights supports (#2 and #3) by using bolts
(#18), washers (#23), and plastic nuts (#27).
See Fig. A – Step 3.
Step 4:
Fasten the rear cross brace (#5) to the rear
upright supports (#3) by using bolts (#18),
washers (#23), and plastic nuts (#27). Insert
the leg caps (#33) into all of the base feet.
Tighten all of the plastic nuts and bolts.
See Fig. A – Step 4 and Step 5.
Step 1
Step 2
Step 3
Step 5
STOP DON’T RETURN TO STORE!
22
2
2
18
33
33
7
7
16
16
23
23
29
27 2
2
2
3
3
33
44
1
3
22
28
28
22
22
25
25
17
17
Do not tighten bolts
after Step 1. Fasten
all bolts after Fig A.
Step 4
18
23
29
27
33
5
23
Step 1 Step 2
31

PAGE 4 OF 7
Fig. C
Step 3
Step 4
Step 5
Step 6:
Insert the front/rear canopy braces (#6) into the
sleeves on the canopy (#36). See Fig. C – Step 3.
Step 7:
Insert the front/rear canopy brace (#6) tube ends
into the U-shaped side canopy braces (#7).
See Fig. C – Step 4.
Step 8:
Insert the U-shaped side canopy brace (#7)
corners into the pockets on the canopy (#36).
See Fig. C – Step 5.
Fig. D
STOP DON’T RETURN TO STORE!
36
36
36
36
1
6
6
6
77
6
Step 9:
Fasten the canopy/frame connectors (#31) on the
canopy assembly to the adjustable teeth on the top
cross beam w/adjustable teeth (#1) by using plastic
screws (#32). Repeat this procedure for both sides.
See Fig. D – Step 1 and Step 2.
32 31
31 32
Step 1
Step 2

PAGE 5 OF 7
STOP DON’T RETURN TO STORE!
Fig. E
Fig. F
Step 10:
Place the left seat assembly (#8) and the right seat
assembly (#9) onto a non-abrasive surface, such
as a carpet. Fasten the front support brace (10) to
the left seat assembly (#8) and the right seat
assembly (#9) by using bolts (#17), washers (#22),
and nuts (#26). See Fig. E – Step 1.
Step 11:
At the rear of both seat assemblies (#8 and #9),
fasten the back support brace (11) by using bolts
(#19) and washers (#23). See Fig. E – Step 2.
Note:
The arrow marks on the back support brace (#11)
should coincide with Fig. E – Step 2 to ensure
proper assembly.
Step 12:
Open the left seat assembly (#8) and the right seat
assembly (#9). Insert the swing arm left (#12) and
the swing arm right (#13) into the back of the left
seat assembly (#8) and the right seat assembly
(#9). Secure in place using bolts (#19) and washers
(#23). Repeat the same procedure for both
sides. Insert the swing arm left (#12) and swing arm
right (#13) into the front of the left seat assembly
(#8) and the right seat assembly (#9). Secure in
place using bolts (#20), washers (#23), and plastic
nuts (#27). Repeat the same procedure for both
sides. Insert the swing arm left (#12) and swing arm
right (#13) into the mid front of the left seat
assembly (#8) and the right seat assembly (#9).
Secure in place using bolts (#21) and washers (#22
and #24). See Fig. E – Step 3.
Step 13:
Attach the swing arm tubes (#14) to the swing
arms (#12 and #13) by using bolts (#20), washers
(#23), and plastic nuts (#27). Repeat the same
procedure for both sides. See Fig. F.
22
19
19
21 28
8
9
29
29
29
28
26
17
9
9
10
8
8
22
23
23
19
Step 1
Step 2
Step 3
11
12
8
12
24
20
20
29
29
23
23
23
14
14
14
14
27
27
13
22
23
12
13
23

PAGE 6 OF 7
STOP DON’T RETURN TO STORE!
Fig. G
Step 14:
Hook the suspension springs (#15) into the top of
both holes in the swing arm tubes (#14). Repeat the
same procedure for both sides. See Fig. G.
Step 15:
Hang the other ends of the suspension springs
(#15) into the holes located in the angled brace on
the top cross beam w/adjustable teeth (#1). Repeat
the same procedure for both sides.
See Fig. H – Step 1 and Step 2.
Step 16:
Tighten the bolts on the seat assemblies (#8 and
#9). To assure stability, double check that all of the
bolts have been completely tightened and cover
them with bolt caps (#28 and #29) and plastic caps
(#30).
Warning:
Make sure that both ends of the suspension
springs (#15) go completely through the holes in
the angled braces on the top cross beam
w/adjustable teeth (#1) and the swing arm tubes
(#14).
Fig. H
14
14
15 15
15
15
14 14
15
1
15
30
Step 1
Step 2

PAGE 7 OF 7
STOP DON’T RETURN TO STORE!
Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use
bleach, acid, or other solvents on the frame or fabric.
• The cushions and canopy may be surface washed with mild soap and water if necessary. Commercial foaming
upholstery cleaner may also be used. Rinse well and hang to dry. Do not machine wash or dry.
• We recommend the use of furniture covers to protect your swing when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your swing.
• In order to prolong the life and beauty of your swing, we recommend that the cushions and fabric parts be
stored in a dry and protected area during off season periods (i.e. overnight or on rainy days).
Special Warnings
• The user of this swing should always inspect it before each use.
• It is essential to place this swing on level ground and not less than 6 feet from any obstruction; such as fences,
garages, houses, overhanging branches,laundry lines, or electrical wires.
• Check the tightness of all of the nuts and bolts on a regular basis.
• Make sure that the suspension springs are properly secured before each use.
• Always remove the canopy in heavy wind conditions; otherwise, the canopy may tip over and cause damage to
its parts.
• The manufacturer will not accept responsibility for unauthorized repairs or modifications to the swing or its
parts.
• Oil all of the metal parts that move regularly.
• Weight limit is 500lbs.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.