Courtyard Creations XLS005U-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
XLS005U-WM
Weight limit for each shelf is 30kg or 66lbs.
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and fittings
required.
Keep children away during assembly. This item contains small parts that can be swallowed by children.
Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
PAGE 1 OF 3 COURTYARD CREATIONS INC.
!
!
!
!
!
!
STOP DON’T RETURN TO STORE!
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY
1 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
8
12
4
8
1
1
4
4
1
1
1
1
XLS005U-CS04-F
XLS005U-CS04-D
XLS005U-CS04-G
XLS005U-CS04-E
47LA66191
62XLS005UB101
62XLS005UB102
17C17A0403001Y4
17C01A0706001Y4
17FA05040301-Y4
17C33A0709001Y4
18000337001
18000337004
17KAA0101----Y4
RIGHT SUPPORT FRAME
LEFT SUPPORT FRAME
RIGHT LEG
LEFT LEG
MESH FRAME A
BACK FRAME
MESH FRAME B
UPPER STORY BACK
SCREW ST4.2*12
BOLT M6*16
BOLT CAP M6
WASHER d6.5*D13*1.0
BOLT M6*25
BOLT CAP
HEX.KEY WRENCH 4MM
Attention:
Make sure that each bolt needed for all steps matches the
corresponding figure to ensure proper assembly.
Note:
The label that are marked “1, 2, 3, 4” on the support frames
and the legs should coincide with Figure 1 & 2 to ensure proper
assembly.
FIGURE 1
9
1
1
Step 1:
Place the right support frame (#1) onto a non-abrasive surface,
such as a carpet. Insert the right leg (#3) to the right support
frame (#1) by using screws (#9). Repeat the same procedure
for the left support frame (#2) and the left leg (#4).
See Figure 1.
3
47LA71051
R
3
3
R
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex.Key Wrench (See Part #15)

PAGE 2 OF 3
STOP DON’T RETURN TO STORE!
FIGURE 2 FIGURE 3
Step 3:
Fasten the back frame (#6) to the legs (#3, #4) by using bolts
(#11) and washers (#12). Keep the bolts loose.
See Figure 3.
Step 4:
Put the mesh frame B (#7) into the holders located on the
legs (#3, #4). See Figure 4.
Step 5:
Fasten the upper story back (#8) to the support frames
(#1, #2) by using bolts (#11) and washers (#12).
See Figure 5.
Step 6:
Put the mesh frame B (#7) into the holders located on the
support frames (#1, #2).
Make sure that all of the bolts have
been tightened completely and cover them with bolt caps (#13,
#14).
See Figure 6.
7
7
4
7
FIGURE 6
FIGURE 5
Step 2:
Put the mesh frame A (#5) into the holders located on the
legs (#3, #4) by using bolts (#10) and washers (#12). Keep
the bolts loose. See Figure 2.
FIGURE 4
44
L
3
3
4
3
2
12
8
1
11
12 14
R
5
16
6
#10 BOLT M6*16
10 13
12 25
#11 BOLT M6*25
25
#11 BOLT M6*25
11
12 14
2
7
72
1

FULLASSEMBLY
PAGE 3 OF 3
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
MissingA Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THESTORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
STOP DON’T RETURN TO STORE!
Step 7:
See Full Assembly.
Cleaning and Maintenance
•Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach, acid, or other
solvents on the frame parts.
•Inspect and tighten all bolts and fasteners on a regular basis to ensure proper performance and safety of your stand.
•When moving the stand, lift. Do not drag this stand.
•We recommend the use of furniture covers when not in use.
•In order to prolong the life and beauty of your stand, we recommend that it be stored in a dry and protected area during
off season periods.