Courtyard Creations KWS620J-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PAGE 1 OF 3 COURTYARD CREATIONS INC.
STOP DON’T RETURN TO STORE!
Step 1:
Place the right arm (#4) onto a non-abrasive surface,
such as a carpet. At the front of the bench, fasten
both the left arm (#3) and the right arm (#4) to the
seat assembly (#2) by using bolts (#5 and #6) and
washers (#8). Keep the bolts loose. See Figure 1.
Note:
The labels marked “L” and “R” on the arms (#3 and
#4) should coincide with Figure 1 to ensure proper
assembly.
KWS620J-WM
FIGURE 1
RIGHT ARM
BOLT M6*16
BOLT M6*14
SEAT ASSEMBLY
BOLT M6*35
WASHER d6.5*D13*1.0
BOLT CAP
HEX.KEY WRENCH 4MM
HEX.KEY WRENCH 6MM
BOLT CAP M6
LEFT ARM
PARTS LIST
PART
NO.
PART
NO.
1 1 7
2
4
2
8
1
1
8
9
10
11
12
1
1
1
2
4
2
3
4
5
6
17C02A0712003Y4
17FA05040301-Y4
18000337004
18000337006
17KAA0101----Y4
17KAA0201----Y4
KWS620J-CS02
KWS620J-CS03
KWS620J-CS01
KWS620J-CS04
17C33A0706001Y4
17C02A0755131Y4
BACK ASSEMBLY
MATERIAL
CODE
MATERIAL
CODE
PART PARTQ’TY Q’TY
Attention:
Make sure that each bolt needed for all steps
matches the corresponding figure to ensure proper
assembly.
16
5
610 2
4
3
9
8
14
#5 BOLT M6*16
#6 BOLT M6*14
L
R
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
!
!
!
!
!
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]

STOP DON’T RETURN TO STORE!
PAGE 2 OF 3
FIGURE 2 FIGURE 3
FULL ASSEMBLY
Step 3:
Fasten the back assembly (#1) to the arms (#3
and #4) by using bolts (#7). Make sure that all
of the bolts have been tightened completely and
cover them with bolt caps (#9 and #10).
See Figure 3.
Step 4:
You can use this bench with three positions. Pull the seat assembly to the different positions.
See Full Assembly.
35
6
7 10
710
10
1
#7 BOLT M6*35
14
#6 BOLT M6*14
2
3
4
3
4
Step 2:
At the rear of the bench, fasten both the left arm
(#3) and the right arm (#4) to the seat assembly
(#2) by using bolts (#6). Keep the bolts loose.
See Figure 2.
Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame parts.
•
We recommend the use of furniture covers when not in use.
• Inspect and tighten all bolts and fasteners
on a regular basis to ensure the proper performance and
safety of your bench.
• In order to prolong the life and beauty of your bench, we recommend that it be stored in a dry and
protected area during off season periods.
Back assembly

The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
STOP DON’T RETURN TO STORE!
PAGE 3 OF 3