Crestron UC-2-Z User manual

The Crestron® UC-2-Z(-I) is a tabletop conference device included in
select Crestron Flex conference systems.
For instructions on system connection and configuration, refer to the
system's Quick Start Guide listed below:
lUC-MM30-Z(-I) and UC-MM30-Z-L(-I)
lUC-MMX30-Z(-I) and UC-MMX30-Z-L(-I)
In the Box
1 UC-2-Z(-I), Crestron Flex Tabletop Conference Device for
Zoom Rooms™ Systems
Additional Items
1 PoE+ Injector (2055605)
2 Cable, CAT5e, RJ-45 - RJ-45, 11.8 ft (3.6 m) (2056204)
1 Cable, USB 2.0, A - Micro B, 5.8 ft (1.8 m) (2055579)
Buttons and Indicators
Tap one of the four mute buttons located at each corner of the device to
mute or unmute the integrated microphone.
A light bar is located above the screen. LEDs are located behind the
mute buttons and light bar and will respond to muting or unmuting the
microphone.
The four mute buttons and the light bar will display red or green to
indicate the following states:
lLighted green: The microphone is unmuted.
lLighted red: The microphone is muted.
lFlashing green: The device is powering on.
UC-2-Z(-I) QuickStart
Crestron Flex Tabletop Conference Device for Zoom Rooms™ Systems
1

Factory Reset the Device
A factory reset may be performed when troubleshooting the conference
device.
To perform a factory reset on the conference device:
1. Power cycle the device by disconnecting and reconnecting the CAT5e
cable from the conference device.
2. When the device powers on and the LEDs flash green, tap the button
below the Crestron® logo 10 times. A factory reset confirmation
screen appears.
3. Tap one of the mute buttons to move the selector on the factory
reset confirmation screen to Yes. Tap the button below the Crestron
logo to confirm the factory reset.
4. The device will reboot. Configure the device according to the Crestron
Flex system's Quick Start Guide.
Visit the Product Page
Scan the QR code to visit the Crestron Flex conference system's product
page.
UC-MM30-Z
www.crestron.com/model/6511341
UC-MM30-Z-I
www.crestron.com/model/6511342
UC-MM30-Z-L
www.crestron.com/model/6512206
UC-MM30-Z-L-I
www.crestron.com/model/6512307
2
UC-2-Z(-I) QuickStart
Crestron Flex Tabletop Conference Device for Zoom Rooms™ Systems

UC-MMX30-Z
www.crestron.com/model/6511631
UC-MMX30-Z-I
www.crestron.com/model/6511632
UC-MMX30-Z-L
www.crestron.com/model/6512190
UC-MMX30-Z-L-I
www.crestron.com/model/6512191
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Regulatory Model: M201928001
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Zoom Rooms is
either a trademark or registered trademark of Zoom Video Communications, Inc. in the
United States and/or other countries. Other trademarks, registered trademarks, and
trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the
marks and names of others. Crestron is not responsible for errors in typography or
photography.
©2021 Crestron Electronics, Inc.
Doc. 8783A
09/29/21
3
UC-2-Z(-I) QuickStart
Crestron Flex Tabletop Conference Device for Zoom Rooms™ Systems