Crestron UC-M70-NC-T User manual

The UC-M70-NC-T Crestron Flex tabletop conferencing system provides
a large room conference solution for use with Microsoft Teams® Rooms
software. It supports single or dual video displays and features a
Crestron Flex tabletop conference device and UC bracket assembly.
Minimum Requirements:
lA Microsoft Teams certified USB Camera (not included).
lA video display (not included) connected to the UCEngine. A second
display is optional.
lA Microsoft Teams Rooms provisioned account (not included).
In the Box
Tabletop Conference Device
1 Tabletop Conference Device, Microsoft Teams video
(6510716)
1 Cable, CAT5e, RJ-45 - RJ-45, 12 ft (3.7 m) (2033988)
1 Cable Retention Plate (2047908)
3 Tie Wrap (2047935)
UC Bracket Assembly
1 UC Bracket Assembly with UC Engine and HDMI® content
ingest (UC-BRKT-200-S-T-ASSY,6512689)
2 Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (9.5mm x
12.7mm) (2052565)
1 Key, Anchor (4529654)
2 Screw, 8-AB x 1-1/2 in. (38.1 mm), Pan Head, Combo
(2052567)
4 Tie Wrap (2047935)
Additional Items
1 Microphone pod (6508084)
1 Cable, CAT6a, RJ-45 - RJ-45, 20 ft (6.1 m) (6507640)
1 Cable, CAT5e, RJ-45 - RJ-45, 7 ft (2.1 m) (6509924)
1 Cable, DisplayPort™ to HDMI, 6 ft (1.8 m) (6508282)
1 Cable, HDMI, 20 ft (6.1 m) (6503567)
1 Cable, HDMI, 6 ft (1.8 m) (6512150)
1 Cable, USB 2.0, A - Micro-B, 6 ft (1.8 m) (6510947)
1 Cable, USB Extension, USB Type A Male-to-Female, 15 ft
(4.6m) (6508260)
1 Power supply (6500187)
1
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

Mount Devices
Mount the UC Bracket Assembly
Mount the UC Bracket Assembly to VESA® compliant display devices, a
wall, or other building structure. Anchors and screws are supplied for
installation on walls with 3/8 in. (9.5mm) to 3/4 in. (19mm) thickness.
CAUTION: Preinstalled screws may protrude from the back of the
UC Bracket Assembly. Exercise caution when handling the UC
Bracket Assembly to avoid scratching or damaging surfaces.
NOTE: The integrated cable tie wraps are reusable. Avoid damaging
the cable tie wraps.
Install the Cable Retention Plate
The included cable retention plate provides tie-down points for cables
that connect to the Crestron® conference device.
Remove the adhesive backing from the cable retention plate and install
the plate on the underside of the conference device as shown in the
following diagram. Ensure the cable retention plate is firmly attached
before securing cables.
CAUTION: When turning over the device, place the device on a soft
surface to avoid damage.
NOTE: If a swivel mount kit (CCS-UCA-SMK) is to be used, use the
cable retention bracket included with the swivel mount kit as
described in the CCS-UCA-SMK DO Guide (Doc. 7882).
2
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

Connect
Identify the UC Bracket Assembly
The UC Bracket Assembly is available in two models. Identify the model included with your Crestron Flex system. Tap or click the corresponding
image below to navigate to the appropriate connection instructions.
UC Bracket Assembly with HD-CONV-USB-200 UC Bracket Assembly with HD-CONV-USB-300
3
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

System Overview
For UC Bracket Assembly with HD-CONV-USB-200
When connections are complete, the system appears as shown below. Refer to Make Connections for detailed connection instructions.
4
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

For UC Bracket Assembly with HD-CONV-USB-300
When connections are complete, the system appears as shown below. Refer to Make Connections for detailed connection instructions.
5
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

Make Connections
NOTE: For reference, the UC Bracket Assembly is shown with the HD-CONV-USB-200 in the following connection diagrams. Unless otherwise
indicated in this guide, the connections remain the same for the UC Bracket Assembly with HD-CONV-USB-200 and HD-CONV-USB-300.
1. Make UC Engine connections as shown in the following illustrations. The conference device can communicate with the UC Engine over a direct
connection or a network connection. Select one of the connection types as described below.
lMake a direct connection for simple installation and setup. Only use the direct connect adapter to connect the conference device to the UC
Engine. Do not use the direct connect adapter to connect the UC Engine to the network.
Direct Connection
6
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

lMake a network connection if the system is to be managed by the XiO Cloud® service.
NOTE: When a network connection is used, disconnect the direct connect adapter from the UC Engine.
Network Connection
7
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

2. Connect displays to the UC Engine.
8
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

3. Connect a camera (not included) to the UC Engine as shown in the image below. Do not connect the camera to any of the other USB ports.
9
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

4. Connect a laptop to the HD-CONV-USB-200 or HD-CONV-USB-300.
5. Bundle the cables to the bracket assembly with the integrated cable tie wraps. The cable tie wraps are reusable.
10
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

Bundle Cables
Bundle the cables together and use a provided tie wrap to secure the
bundle to one of the positions on the cable retention plate at the rear of
the device. Avoid bundling power and data cables together.
Configure
Apply Power
Press the power button on the bottom of the UC Engine and apply
power to all of the other devices in the system. The conference device
will display its IP address.
Configure the Conference Device
NOTE:If a Direct Connection was made between the conference
device and the UC Engine, skip to Configure the System.
1. On a computer, enter the IP address displayed on the conference
device into a web browser.
NOTES:
lThe device and computer must be on the same network switch
and VLAN.
lA login with administrative rights for the device is required.
2. Log in to the device and navigate to DEVICE >Applications.
3. Enter the following information in the appropriate fields:
lTeams Video PC Address: Enter the IP address or hostname of the
UC Engine.
NOTE: The hostname is printed on a label affixed to the UC
Engine.
lTeams Video PC Port: By default, port number 49500 is used. If a
different port number has been configured on the UC Engine,
enter that port number instead.
lTeams Video Username: Enter the login username for the UC
Engine. (The default username is “admin”.)
lTeams Video Password: Enter the login password for the UC
Engine. (The default password is “sfb”.)
4. Select Save Changes.
Configure the System
Use the conference device and your Microsoft Teams credentials to
configure the UC Engine. For detailed information on deploying
Microsoft Teams Rooms, refer to the Microsoft Teams Rooms
documentation.
11
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms

Visit the Product Page
Scan the QR code to visit the product page.
UC-M70-NC-T
www.crestron.com/model/6513793
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software
is licensed to Crestron dealers, CSPs, and end-users under a separate End-User
License Agreement. Both of these Agreements can be found on the Crestron website
at www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information,
visit www.crestron.com/opensource.
Crestron, the Crestron logo and XiO Cloud are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the
United States and/or other countries. Microsoft Teams is either a trademark or
registered trademark of Microsoft Corporation in the United States and/or other
countries. DisplayPort and VESA are either trademarks or registered trademarks of
Video Electronics Standards Association in the United States and/or other countries.
Other trademarks, registered trademarks, and trade names may be used in this
document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names of
others. Crestron is not responsible for errors in typography or photography.
©2024 Crestron Electronics, Inc.
Doc. 9473A
01/25/24
12
UC-M70-NC-T QuickStart
Crestron Flex Tabletop Large Room Conference System for Microsoft Teams® Rooms