Crestron UC-BRKT-100-SD-Z-ASSY User manual

The Crestron® UC-BRKT-100-SD-Z-ASSY simplifies installation of a Crestron Flex UC conference system, providing all the necessary components
connected and mounted on a single VESA® compliant mounting bracket. The bracket mounts behind a display device in a conference room or
directly to drywall using the included anchors. The UC-BRKT-100-SD-Z-ASSY is intended for use with M-Series and B-Series of Crestron Flex single
display conference systems. For more information, visit www.crestron.com/flex.
Check the Box
Item Qty
Anchor, Drywall, Plastic, 3/8 in. x 1/2 in. (P/N 2052565) 2
Key, Anchor (P/N 4529654) 1
Bit, Spanner, 1/4 in. (P/N 2052847) 1
Screw, 6-32 x 3/8 in., Undercut Head, Spanner (P/N 2052846) 2
Screw, 8-AB x 1-1/2 in., Pan Head, Combo (P/N 2052567) 2
Power Cord (P/N 2053985) 1
Tie Wrap (P/N 2047935) 4
Install the Wall Bracket Assembly
The wall bracket can be mounted to VESA compliant display devices or building structure. Anchors and screws are also supplied for installation on
walls 3/8 in. to 3/4 in. thickness.
NOTES:
• The integrated cable tie wraps are reusable. Take care to avoid damage to the cable tie wraps.
• The wall bracket assembly includes an opening and pass through screw holes for placement over a single gang US electrical wall box that can
be covered by a decorative wall plate. If the wall plate opening will be positioned over an electrical wall box, longer screws will be needed to
secure the decorative wall plate to the electrical box. Do not attempt to secure the wall bracket assembly with the wall plate opening screws.
UC-BRKT-100-SD-Z-ASSY (connecting cables not shown)
16.00 in.
406.40 mm
14.00 in.
355.60 mm
7.00 in.
177.80 mm
15.30 in.
388.62 mm
15.42 in.
391.67 mm
13.30 in.
337.82 mm
5.00 in.
127.00 mm
11.11 in.
282.07 mm
1.68 in.
42.78 mm
UC-ENGINE-SD-Z
Connector Cover
Connector Cover
Wall Plate Opening
Power Pack
Reusable Cable Tie Wrap (x4)
HD-CONV-USB-200
UC-BRKT-100-SD-Z-ASSY
UC Engine Assembly

Open the Connector Covers
Connector Cover
#1
#1
UC-ENGINE-SD-Z
Connector Cover
Connect Devices
Connect touch screens, conference systems, display devices, network cables, and peripherals to components on the UC-BRKT-100-SD-Z-ASSY. Refer
to the quick start guide included with the Crestron Flex UC System.
CAUTION: The bracket assembly has cables and devices that are connected at the factory. DO NOT DISCONNECT ANY DEVICES OR CABLES THAT
ARE ALREADY CONNECTED.
Secure Connector Covers
Connector Cover
or
NOTE: For additional security, replace the screws with the included spanner screws. A 1/4 in. bit is supplied to install the spanner screws.
For Additional Information
Scan or click the QR codes below for detailed product information.
UC-BRKT-100-SD-Z-
ASSY
Flex Solutions
Compliance and Legal
Original Instructions: The U.S. English version of this document is the original instructions. All other languages are a translation of the original instructions.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. VESA is either a trademark or registered trademark of Video Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to
either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: [phone]
www.crestron.com
Quick Start - Doc. 8527A
(2054416)
10/18/19
Specifications subject to
change without notice.