Crestron TSR-302 User manual

Crestron TSR-302
Handheld Touch Screen Remote
Configuration Guide

The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Crestron Toolbox, and Rava are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United
States and/or other countries. Wi-Fi, WPA, and WPA2 are either trademarks or registered trademarks of Wi-Fi Alliance in the United States and/or
other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors
in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2014 Crestron Electronics, Inc.

Crestron TSR-302 Handheld Touch Screen Remote
Configuration Guide – DOC. 7663A Contents
•
i
Contents
Handheld Touch Screen Remote: TSR-302 1
Access the Setup Screens........................................................................................................... 1
Configure the TSR-302.............................................................................................................. 3
RF Setup ...................................................................................................................... 3
Audio Setup .................................................................................................................8
Display Setup .............................................................................................................. 8
Timeouts......................................................................................................................9
WiFi Setup................................................................................................................. 10
Diagnostics ................................................................................................................ 16
About ......................................................................................................................... 21
Save & Exit ............................................................................................................... 22

Crestron TSR-302 Handheld Touch Screen Remote
Configuration Guide – DOC. 7663A Handheld Touch Screen Remote: TSR-302
•
1
Handheld Touch Screen Remote:
TSR-302
Access the Setup Screens
The main menu is the starting point for configuring the TSR-302 from Crestron®.
NOTE: If no project has been loaded or if an invalid project has been loaded, the
TSR-302 defaults to a screen that allows access to the main menu.
The setup screens enable basic configuration of the TSR-302 prior to regular
operation.
If a project is running, the main menu can be accessed using one of two methods: via
the first four buttons on the device or via Crestron Toolbox™.
Via Device Buttons Press (Power), (Home), MENU, and GUIDE on the TSR-302 in sequence
twice (press , , MENU, GUIDE, , , MENU, GUIDE) within a 5 second
period.
Via Crestron Toolbox Perform the following procedure to access the main menu via Crestron Toolbox.
1. Establish communication with the TSR-302.
2. Right-click on the device and select Functions >Setup Mode.
3. Select Enter Setup Mode. The main menu is displayed, as shown in the
illustration on the following page.
NOTE: Select Exit Setup Mode to exit the setup menu.

Handheld Touch Screen Remote Crestron TSR-302
2
•
Handheld Touch Screen Remote: TSR-302 Configuration Guide – DOC. 7663A
TSR-302 Main Menu
The main menu displays the current battery status, the gateway (RF) signal strength,
and Wi-Fi®signal strength and also has RF Setup, Audio Setup, Display Setup,
Timeouts, WiFi Setup, and Diagnostics buttons. In addition, there is a button that
toggles on-screen messages on and off, a button that provides information about the
TSR-302, and a Save & Exit button. The functions of each are detailed in the next
section of this guide.

Crestron TSR-302 Handheld Touch Screen Remote
Configuration Guide – DOC. 7663A Handheld Touch Screen Remote: TSR-302
•
3
Configure the TSR-302
RF Setup
From the main menu, touch RF Setup to display the RF Setup menu.
RF Setup Menu
The RF Setup screen shows the RF signal strength and has controls for enabling or
disabling roaming.
Before a TSR-302 can be used with a Crestron control system, it must first be
acquired by a CEN(I)-ERFGW-POE Extended Range RF Wireless Gateway (sold
separately).
Single Gateway Setup When roaming is not enabled, i.e., a single gateway is used, there is a Single
Gateway Setup button at the bottom of the screen.
To acquire a TSR-302, perform the following steps:
1. Use a stylus or other thin-tipped object to press ACQUIRE on the
CEN(I)-ERFGW-POE gateway to enter Acquire mode. The accompanying
LED illuminates, indicating the unit is ready to link with the touch screen.
(The gateway can also be put into Acquire mode via Crestron Toolbox.)
2. Place the TSR-302 in Acquire mode by touching Acquire on the RF Setup
menu, shown in the following illustration. The screen displays an “Acquire
in progress” message and the TSR-302 is automatically acquired by the
gateway within 2 minutes.

Handheld Touch Screen Remote Crestron TSR-302
4
•
Handheld Touch Screen Remote: TSR-302 Configuration Guide – DOC. 7663A
RF Setup Menu (Acquire in Progress)
3. When the process is complete, the screen displays an “Acquire OK”
message. Press ACQUIRE on the gateway to exit Acquire mode. The LED
turns off.
RF Setup Menu (Acquire OK)
NOTE: Select an RF channel between 12 and 23 for maximum range. Channels 11
and 24 through 26 have less range but are available if RF interference requires
moving the RF channel.
NOTE: The RF ID of the unit must match the RF ID specified in the SIMPL
Windows program.
For details, refer to Best Practices for Installation and Setup of Crestron RF Products
(Doc. 6689) at www.crestron.com/manuals.

Crestron TSR-302 Handheld Touch Screen Remote
Configuration Guide – DOC. 7663A Handheld Touch Screen Remote: TSR-302
•
5
Gateway Roaming Setup When roaming is enabled, i.e., more than one gateway is used, there is a Gateway
Roaming Setup button at the bottom of the screen.
RF Setup Menu (Gateway Roaming Enabled)
Touch Gateway Roaming Setup to display the RF Roaming Setup menu.
RF Roaming Setup Menu
Touch RF Settings to access the RF Settings screen

Handheld Touch Screen Remote Crestron TSR-302
6
•
Handheld Touch Screen Remote: TSR-302 Configuration Guide – DOC. 7663A
RF Settings Screen
After making any desired settings, touch to return to the RF Roaming Setup
menu.
Enable multiple gateways to acquire a TSR-302 by performing the following steps:
NOTE: Only one gateway at a time can be in Acquire mode.
1. Use a stylus or other thin-tipped object to press ACQUIRE on one of the
gateways to enter Acquire mode. The accompanying LED illuminates,
indicating the unit is ready to link with the touch screen. (The gateway can
also be put into Acquire mode via Crestron Toolbox.)
2. On the RF Roaming Setup menu, touch Acquire Gateways to display the
Roaming Setup menu.
Roaming Setup Menu