Crestron infiNET CLW-SLVS1RF User manual

Crestron CLW-SW1/4RF,
CLW-SWS1/4RF, CLW-SLVS1RF
infiNET™ Switches
Operations Guide

This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
Windows®and Windows®XP are registered trademarks of Microsoft Corporation in the United States and other countries.
©2005 Crestron Electronics, Inc

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
Contents
infiNET™ Switches: CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF 1
Introduction ...............................................................................................................................1
Features and Functions................................................................................................1
Specifications ..............................................................................................................2
Physical Description....................................................................................................4
Industry Compliance ...................................................................................................7
Acquiring the Switch on the infiNET Network .........................................................................8
Acquiring the Switch................................................................................................... 8
Removing Gateway Information from a Switch..........................................................9
Operation ...................................................................................................................................9
Mode Selection Switch................................................................................................ 9
-SLVS1RF.................................................................................................................11
Restoring Default Settings......................................................................................... 11
LED Behavior............................................................................................................11
Identity Code ...........................................................................................................................12
Using Touch Settable ID (TSID) to Set MNET ID ...................................................12
Manually Setting the MNET ID in Crestron Toolbox............................................... 19
Programming Software............................................................................................................21
Earliest Version Software Requirements for the PC .................................................22
Programming with D3 Pro & SystemBuilder............................................................ 22
Programming with SIMPL Windows ........................................................................23
Uploading and Upgrading........................................................................................................ 28
Establishing Communications ...................................................................................28
Troubleshooting Communications ............................................................................31
Uploading a SIMPL Windows Program.................................................................... 31
Firmware Upgrade..................................................................................................... 34
Problem Solving ...................................................................................................................... 36
Troubleshooting......................................................................................................... 36
Bootloader .................................................................................................................37
Further Inquiries ........................................................................................................ 38
Future Updates .......................................................................................................... 38
Return and Warranty Policies .................................................................................................. 39
Merchandise Returns / Repair Service ...................................................................... 39
CRESTRON Limited Warranty.................................................................................39
Operations Guide - DOC. 6397 Contents •i

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
infiNET™ Switches:
CLW-SW1/4RF, -SWS1/4RF,
-SLVS1RF
Introduction
Features and Functions
The CLW-SW1RF (-SW1RF) one-button switch and CLW-SW4RF (-SW4RF)
four-button switch are stand-alone wall box switches that can also act as wireless
infiNET™ devices that report to a Crestron®control processor via a Crestron
infiNET wireless gateway.
infiNET Switches Functional Summary
• Two-way infiNET switches
⇒
⇒
⇒
⇒
2.4 GHz infiNET mesh network technology
Range up to 150 feet indoors, or 250 ft outdoors (subject to site-
specific conditions)
Range may be increased with the use of additional infiNET devices
or C2N-MNETRPT repeaters
“Wi-Fi” friendly operating frequency to avoid interference
• One-button and four-button configurations available in white, black,
and almond
• Can be ordered with custom-engraved buttons
• Can operate as a local load control or infiNET keypad.
These switches can be operated with a user-adjustable delay up to 10 minutes and 55
seconds. For more information, refer to “Operation” on page 9 for more information.
These infiNET switches are a part of Crestron’s line of lighting products using
infiNET mesh network technology. infiNET technology is “Wi-Fi” friendly and
provides fault tolerance and increased effective signal strength as network devices
are added.
As an infiNET device, these switches communicate with a Crestron control system
via a C2N-MNETGW infiNET Gateway. Up to 30 infiNET devices (including
C2N-MNETRPT infiNET Repeaters) can communicate with one C2N-MNETGW
Operations Guide - DOC. 6397 infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •1

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
infiNET Gateway and, if more devices are needed, more C2N-MNETGW gateways
may be added to a Cresnet®network.
Crestron infiNET switches operate on the 2.4 GHz “ISM band” (2400 MHz to
2483.6 MHz) at 10 mW. The output power of these devices allow RF signals to
travel approximately 150 feet indoors and 250 feet outdoors (subject to site-specific
conditions) without the use of repeaters or other infiNET devices. The range is
dependent on construction of the building, obstructions, and RF interference from
other devices. The location of the dimmer is an important factor in determining RF
performance. Adding more infiNET devices or repeaters to the network effectively
increases the range, strength, and reliability of the network.
The -SW1RF and -SW4RF feature a three-position mode selection switch. Refer to
“Operation” on page 9 for more information. In the absence of control system
communications, the switch can still be used to control the attached load.
The CLW-SWS1RF (-SWS1RF) and CLW-SWS4RF (-SWS4RF) are similar to the
-SW1RF and -SW4RF (respectively) with the added capability of working with one
or more slave units (CLW-SLVS1RF) in a multi-switch / single circuit application.
For more information, refer to the latest version of the infiNET Switches Installation
Guide (Doc. 6293) which is available from the Crestron website
(www.crestron.com/manuals).
The CLW-SLVS1RF (-SLVS1RF) is a slave unit that when used in conjunction with
the -SWS1RF or -SWS4RF acts as an additional switch control point in a multi-
switch / single circuit application. It does not connect to an infiNET system and
cannot be used without a -SWS1RF or -SWS4RF. The -SLVS1RF does not have a
mode selection switch. It can only be programmed when used in conjunction with a
-SWS4RF (refer to “Attaching and Detaching the Electrical Load” on page 27).
Otherwise, it will emulate the RUN mode of the -SWS1RF (even if connected to a
-SWS4RF) unless the mode selection switch of the master is set to “OFF”.
These switches can be ordered with custom engraved buttons already installed by
Crestron. Engraved buttons cannot be installed or changed in the field. Contact
Crestron for more information.
These switches are available in white, almond, and black. White units are designated
by part numbers ending in “W”. Almond units are designated by part numbers
ending in “A”. Black units are designated by part numbers ending in “B”. Each
dimmer can be covered with a decorative faceplate (not supplied).
For installation instructions, refer to the latest version of the infiNET Switches
Installation Guide (Doc. 6293), which is available from the Crestron website.
Specifications
Following are specifications for the -SW1RF, -SW4RF, -SWS1RF, -SWS4RF, and
-SLVS1RF.
CLW-SW1/4RF, CLW-SWS1/4RF, & CLW-SLVS1RF Specifications
SPECIFICATION DETAILS
Power Requirements Line Power, 120 VAC, 60 Hz
Operating Frequency 2400 MHz to 2483.6 MHz
(802.15.4 compliant)
RF Output Power 10 mW
(continued on following page)
2 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
CLW-SW1/4RF, CLW-SWS1/4RF, & CLW-SLVS1RF Specifications (continued)
SPECIFICATION DETAILS
Operating Ranges¹
Typical Distance
Indoors (without repeater)
Typical Distance Outdoors
150 ft
250 ft, subject to site-specific conditions
Default MNET ID -SW1RF/-SW4RF: 01/01
-SWS1RF/-SWS4RF: 01/01
Switch Type Single-Pole, Single-Throw
Load Type Incandescent, Tungsten-Halogen,
Fluorescent / High Intensity Discharge (HID),
Electronic Low Voltage, Magnetic Low
Voltage, Neon / Cold Cathode, Ceiling Fan
2-Series Control System Update
File2,3
Version 3.154 or later
Load Ratings4
Incandescent / Tungsten-
Halogen
-SW1RF/-SW4RF: 1000W
-SWS1RF/-SWS4RF: 1000W
-SLVS1RF: N/A
Magnetic Low Voltage5-SW1RF/-SW4RF: 1000VA/750W
-SWS1RF/-SWS4RF: 1000VA/750W
-SLVS1RF: N/A
Neon / Cold Cathode5-SW1RF/-SW4RF: 1000VA/750W
-SWS1RF/-SWS4RF: 1000VA/750W
-SLVS1RF: N/A
Electronic Low Voltage -SW1RF/-SW4RF: 1000W
-SWS1RF/-SWS4RF: 1000W
-SLVS1RF: N/A
Ceiling Fan -SW1RF/-SW4RF: 3A
-SWS1RF/-SWS4RF: 3A
-SLVS1RF: N/A
Minimum Load 40W / 0.5A
Operating Temperature and
Humidity
32°F to 104°F (0°C to 40°C)
10 to 90% Relative Humidity
(Non-Condensing)
-SW1RF/-SW4RF and
-SWS1RF/-SWS4RF:
Height: 4.13 in (10.48 cm)
Width: 2.38 in (6.03 cm)
Depth: 1.88 in (4.77 cm)
Weight: 4.9 oz (0.67 kg)
Dimensions and Weight
-SLVS1RF:
Height: 4.13 in (10.48 cm)
Width: 1.75 in (4.45 cm)
Depth: 1.88 in (4.77 cm)
Weight: 3.6 oz (0.50 kg)
1. The range is dependent on its placement and the building in which it is used. The construction of the
building, obstructions, and RF interference from other devices are factors determining the effective
range of the unit.
2. The latest software versions can be obtained from the Crestron website. Refer to the NOTE
following these footnotes.
3. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product
Catalog for a complete list of 2-Series control systems.
4. Refer to Derating Charts for Multigang Installations in the latest version of the infiNET Switches
Installation Guide (Doc. 6293) which is available from the Crestron website.
Operations Guide - DOC. 6397 infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •3

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
5. VA ratings are for input power to the transformer. If you do not know the input power requirement
of the transformer, use the bulb’s wattage rating to determine proper rating.
NOTE: Crestron software and any files on the website are for Authorized Crestron
dealers and Crestron Authorized Independent Programmers (CAIP) only. New users
may be required to register to obtain access to certain areas of the site (including the
FTP site).
Physical Description
The -SW1RF and -SWS1RF have a light emitting diode (LED) with adjustable
brightness (via Crestron programming software), a rocker button, and a three-
position mode selection switch as shown in the following diagrams. The button may
be pushed at the top or bottom to perform certain functions. Pushing the button in the
middle does not do anything. The function of the pushbutton is determined by the
position of the mode selection switch. For more information, refer to “Operation” on
page 9.
Parts of CLW-SW1RF and -SWS1RF
Button
Mode Selection Switch
RUN SET OFF
CLW-SW1RF/-SWS1RF Shown in White
4 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397

Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF infiNET™ Switches
Physical View of CLW-SW1RF/-SWS1RF (Clockwise from Top; Top, Side, and Front)
1.75 in
(4.45 cm)
2.38 in
(6.03 cm)
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
1.88 in
(4.77 cm)
2.70 in
(6.86 cm)
1.50 in
(3.81 cm)
OFFSETRUN
The -SW4RF and -SWS4RF have a light emitting diode (LED) with adjustable
brightness (via Crestron programming software), four pushbuttons, and a three-
position mode selection switch as shown in the following diagrams. Each of the
buttons may be pushed to perform certain functions. The function of each pushbutton
is determined by the position of the mode selection switch. For more information,
refer to “Operation” on page 9.
Parts of CLW-SW4RF, -SWS4RF
Button 2
Mode Selection Switch
Button 4Button 3
Button 1
RUN SET OFF
CLW-SW4RF/-SWS4RF Shown in White
Operations Guide - DOC. 6397 infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF •5

infiNET™ Switches Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF
Physical View of CLW-SW4RF/-SWS4RF (Clockwise from Top; Top, Side, and Front)
RUN SET OFF
1.75 in
(4.45 cm)
2.38 in
(6.03 cm)
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
1.88 in
(4.77 cm)
2.70 in
(6.86 cm)
1.50 in
(3.81 cm)
The -SLVS1RF is similar in appearance to the -SW1RF and -SWS1RF but does not
have the three-position mode selection switch. The brightness of the LED on the
-SLVS1RF is not programmable.
CLW-SLVS1RF Shown in White
6 •infiNET Switches: Crestron CLW-SW1/4RF, -SWS1/4RF, -SLVS1RF Operations Guide - DOC. 6397