Crestron ZUM-FLOOR-HUB User manual

The Crestron® Zūm® Floor Hub enables centralized management and time
clock for Zūm wireless commercial lighting systems. The device provides a
web-based user interface for easy configuration, control, monitoring, and
scheduling. The time clock feature enables automation of room lighting
and sensing behavior. The Zūm Floor Hub supports up to 1,000 individual
rooms equipped with Zūm lighting systems. The device also enables
integration with other Crestron lighting systems, control systems, touch
screens, shading, HVAC, and more.
In the Box
1 ZUM-FLOOR-HUB, Zūm® Floor Hub
Additional Items
1 Connector, 4-Pin (2003576)
1 Power Pack, 24 VDC, 2.5 A, 100-240 VAC (2045873)
2 Bracket, Rack Ear, 1U (2032122)
4 Foot, 0.5 in. x 0.5 in. x 0.23 in., Rubber, Black (2002389)
1 Power Cord, 5 ft 10 in. (1.78 m) (2042043)
Installation
The ZUM-FLOOR-HUB can be mounted into a rack or placed onto a flat
surface.
Mounting Into a Rack
The ZUM-FLOOR-HUB occupies 1U of rack space.
To install the included rack ears:
1. Use a #1 or #2 Phillips screwdriver to remove the three screws from
each side of the front of the device as shown in the following illustration.
2. Use the screwdriver and the screws removed in the previous step to
attach the included rack ears to the device.
3. Mount the device into the rack using four mounting screws
(notincluded).
1
ZUM-FLOOR-HUB
Zūm® Floor Hub

Placing onto a Flat Surface
When placing the device onto a flat surface or stacking it with other
equipment, attach the included feet near the corners on the underside of
the device.
Make Connections
Hardware Hookup
Make the necessary connections as called out in Connect the Control
Subnet.
When making connections to the ZUM-FLOOR-HUB, note the following:
lUse Crestron power supplies for Crestron equipment.
lThe included cable(s) cannot be extended.
NOTES:
lEnsure the unit is properly grounded by connecting the chassis
ground lug to an earth ground (building steel).
lThe ZUM-FLOOR-HUB can be powered by the 4-position terminal
block connector labeled NET or with the (included) 24 VDC power
pack.
Connect the Control Subnet
The ZUM-FLOOR-HUB has a dedicated Control Subnet that is used for
communication between the control system and Crestron Ethernet
devices. This subnet allows for dedicated communication between the
control system and Crestron Ethernet devices without interferences
from other network traffic on the LAN.
NOTE: Do not connect the CONTROL SUBNET port to the LAN. The
CONTROL SUBNET port must be connected only to Crestron Ethernet
devices.
For details on using the Control Subnet, refer to the 3-Series® Control
Systems Reference Guide (Doc. 7150).
2
ZUM-FLOOR-HUB
Zūm® Floor Hub

Configure the ZUM-FLOOR-HUB
The ZUM-FLOOR-HUB is configured using the web interface. Connect to
the device by entering the device hostname into a web browser. The
hostname is comprised of “ZUM-FL-” and the last 8 digits of the MAC
address (e.g., ZUM-FL-7F8764BF). The New User Registration screen is
displayed during the first connection. Enter the Username, Password,
Firstname, Lastname, and Email Address, and then tap Submit.
The ZUM-FLOOR-HUB settings page opens next, as shown below.
For further configuration, refer to the ZUM-FLOOR-HUB Supplemental
Guide (Doc. 8355A).
3
ZUM-FLOOR-HUB
Zūm® Floor Hub

Visit the Product Page
Scan the QR code to visit the product page.
ZUM-FLOOR-HUB
www.crestron.com/model/6507931
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, 3-Series, Cresnet, and Zūm are either trademarks or
registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in
this document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names of others.
Crestron is not responsible for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc ID 7912B
07/27/20
4
ZUM-FLOOR-HUB
Zūm® Floor Hub