Crivit 14129 User manual

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/66/EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/ off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40 Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7 V
Tail light
Model designation: XC-117D/D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries / re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A/LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/66/ EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/66/ EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/66/ EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/66/EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40 Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/ 66/EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40 Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/ 66/EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40 Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/66/EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/ 66 / EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2 x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40 Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7 V
Tail light
Model designation: XC-117D/D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A/LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/66/EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40 Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

GB/IE/NI GB/IE/NI
GB/IE/NI GB/IE/NI GB/IE/NI
recommended for rechargeable batteries with
1300mAh.
Cleaning and Care
Never fully immerse the lights. Do not use corrosive
or abrasive cleaning agents. Doing so will damage
the lights.
Clean the LED bicycle light set with a slightly damp,
lint-free cloth.
Disposal
The packaging is made of environmentally
friendly materials, which may be disposed of
through your local recycling facilities.
Contact your local refuse disposal authority for more
details on how to dispose of your worn-out product.
To help protect the environment, please
dispose of the product properly, not without
household waste, when it has reached the
end of its useful life. Please contact your local
authority for information on collection points
and their opening hours.
Defective or used batteries/rechargeable batteries must
be recycled according to 2006/ 66/EC and its
amendments. Return batteries/rechargeable batteries
and/or the appliance using the recycling facilities
provided.
Environmental damage due to
incorrect battery/rechargeable
battery disposal!
Never dispose of batteries/rechargeable batteries in your
household waste. They may contain toxic heavy metals
and are subject to hazardous waste regulations. The
chemical symbols of the heavy metals are: Cd = cadmium,
Hg = mercury, Pb = lead. Therefore, dispose of used
batteries/rechargeable batteries through your local
collection site.
Improper battery disposal destroys valuable resources
and the hazardous substances in the batteries may pose
a significant danger to the health and environment.
Separate collection/disposal of old batteries prevents
dangers to the health and environment, and valuable
resources regained by recycling.
Warranty
Dear customer,
This device is covered by a 3-year warranty from the
date of purchase. In the event of product defects, you
have legal rights against the retailer of this product.
Your statutory rights are not limited in any way by our
warranty detailed below.
Warranty terms
The warranty period begins on the date of purchase.
Please retain the original receipt safely. This documen-
tation is required as the proof of purchase. Should a
defect in material or manufacture occur within three
years from the date of purchase of this product, we will
repair or replace - at our choice - it free of charge. This
warranty is conditional on the defective device and the
receipt of purchase being presented within the three
year warranty period, and that there is a brief written
description of the nature of the defect and of the date it
arose. If the defect is covered by our warranty, you will
receive the repaired product or a replacement. A repair
or exchange of the device does not extend a new war-
ranty period. The warranty period will not be extended
by repairs made under warranty. This also applies to
replaced and repaired parts. Any damage or defects
present at the time of purchase must be reported imme-
diately after unpacking. Repairs made after the expira-
tion of the warranty period are subject to payment.
Extent of warranty
The device was manufactured to strict quality guide-
lines and diligently inspected prior to shipment. The
warranty applies to defects in material or manufacture.
This warranty does not apply to product parts subject
to regular wear and therefore considered wear parts or
Installation
Installing the headlight (see Fig. A)
Unscrew the retaining screw 3from the bracket 1.
Position the bracket 1in the desired location on
the handlebar. If necessary, use the reducer
rubbers 2to ensure an optimal fit.
Reinstall the retaining screw 3.
Tighten the screw hand tight. To prevent damage,
do not use tools for this step.
To adjust to the optimal angle to the direction of
travel, loosen the angle adjustment screw 7
2–3 turns using a cross-tip screwdriver.
Adjust to the desired angle and tighten the angle
adjustment screw 7.
Slide the headlight 6into the bracket 1until you
hear it lock into place.
To release, press the headlight lock 8and slide
the headlight 6forward out of the bracket 1.
ATTENTION! Routinely verify the headlamp ad-
justment. The light cone must point straight ahead,
in the direction of travel, and must not be adjusted
too high so as not to blind oncoming traffic.
Installing the tail light
(see Fig. B and C)
Secure the bracket 9to the seat post or the rear
cross-bar using the rubber tab 11 . Be sure there
are no objects in front of the tail light 14 .
Tighten and hook in the rubber tab 11 .
Loosen the retaining screw 15 on the bracket 9
and adjust to the desired angle.
Then tighten the screw. Tighten the screw hand
tight. To prevent damage, do not use tools for this
step.
Slide the tail light 14 into the bracket 9until you
hear it lock into place.
To release the tail light 14 , pull down on the tail
light lock 10 and slide off the tail light 14 .
ATTENTION! The tail lamp must be installed and
adjusted so the reference axis is parallel to the me-
dian longitudinal plane of the vehicle and parallel
to the road.
Inserting batteries into the tail
light (see Fig. D)
Slide the battery cover 16 off to the back.
Insert the batteries into the tail light (2x AAA
1.5V). Ensure the correct polarity.
Then reassemble the light.
Operation
Switching on/off
The headlight 6has three brightnesses.
On/Off switch
press once Power mode (40 Lux) for
riding in unlit areas
press twice Standard mode (20Lux)
for riding in lit areas
press three times Eco mode (10Lux) for
riding in well lit areas
press four times off
Charging the headlight (see Fig. E)
Remove the rubber cover from the battery charging
socket 18 and connect the USB cable 17 to the
battery charging socket 18 .
Then connect the USB plug of the USB cable 17 to
a computer/laptop/standard USB charger with
5V DC and 500–1000mA. Using chargers with
different specifications can damage the rechargea-
ble battery, thus the headlight. Doing so will void
the warranty.
The headlight 6has a battery indicator. If the
indicator lights up red, the rechargeable batteries
are drained. The indicator will light up green whilst
charging. When the rechargeable batteries are
ready to be used again, the indicator will extin-
guish and you can use the headlight 6.
For the included rechargeable batteries to operate
at full power, please do not charge the battery for less
than 10 hours the first time. Please do not stop charg-
ing sooner, even if the LED is already extinguished.
After this, a charging time of approx. 3.5hours is
Rated output: 1W
Protection type: IP44 according to
DIN EN 60529
Rechargeable Li-ion battery: 1300 mAh, 3.7V
Tail light
Model designation: XC-117D /D-LED 3
Rated output: 0.2W
Protection type: IP44 according to
DIN EN 60529
Batteries: 2 x 1.5V AAA LR03
Note: Only use rechargeable 1.2V batteries or
comparable 1.5 V alkaline batteries for the rear light.
Safety instructions
DANGER TO LIFE
AND RISK OF ACCIDENT FOR IN-
FANTS AND CHILDREN! Never leave
children unsupervised with the packing material
due to the suffocation hazard posed by swallowing
parts thereof. Children frequently underestimate the
dangers.
Always keep the product away from children. This
product is not a toy!
This product is not intended to be used by persons
(including children) with impaired physical, sensory
or mental capacity, or lacking experience or knowl-
edge unless supervised by a person responsible for
their safety. Please note, damages caused by incor-
rect handling, non-compliance with the operating
instructions or interference with the device by
unauthorised individuals are excluded.
Never take the product apart. Improper repairs
may result in considerable danger to the user.
Repairs should only be carried out by specialist
personnel. The LED lights are not replaceable.
RISK OF LOSS OF LIFE AND
ACCIDENT! Using the incorrect charger may
cause the headlight 6to be damaged, overheat
or even explode. Doing so will void the warranty.
Safety advice concerning
batteries/rechargeable
batteries
CAUTION! EXPLOSION HAZARD!
Never recharge the batteries!
Remove batteries during extended periods of non-use.
When inserting the battery ensure the polarity is
correct! This is shown in the battery compartment.
If necessary, clean the battery and device contacts
before inserting the battery.
Remove spent batteries immediately from the
device. There is an increased risk of leaks!
Always replace all the batteries at the same time.
Do not mix alkaline batteries and rechargeable
batteries.
Never mix old and new batteries.
Do not dispose of battery/rechargeable batteries
in household waste!
Every consumer is legally obliged to dispose of
batteries/rechargeable batteries in the proper
manner!
CAUTION! EXPLOSION HAZARD!
Keep battery/rechargeable batteries
away from children, do not throw batter-
ies/rechargeable batteries into fire, do not short-
circuit and do not take apart.
Failure to observe this notice may result in deep dis-
charging the batteries. This poses a risk of leaking.
If the batteries have leaked inside the product,
please remove them immediately to prevent prod-
uct damage!
Avoid contact with the skin, eyes and mucous mem-
branes if fluid has leaked from the batteries/re-
chargeable battery. In the event of contact with
battery acid, thoroughly flush the affected area with
clean water and seek immediate medical attention.
Never recharge single-use batteries! Explosion
hazard!
Note: If the red rechargeable battery/battery
control light 513 on the headlight 6or the tail
light 14 lights up, please replace the batteries or
recharge the rechargeable batteries immediately.
Please note, once the battery indicator lights up,
the lights no longer comply with the Road Traffic Act.
List of pictograms used
Read the instructions!
Danger to life and risk of accident for
infants and children!
Observe the warnings and safety
notices!
Caution! Explosion hazard!
Green Dot - Packaging recycling.
Symbol identifying electrical and
electronic devices.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
USB – Universal Serial Bus – Connection
port, e.g. on a computer (charging only).
K XXXXX
Federal Motor Transport Authority test
symbol (K followed by approval number).
Product and packaging should be disposed
in an environmentally friendly manner.
21
PAP
Recycling code for cardboard disposal.
LED Bike Light Set
Introduction
Congratulations on the purchase of your new
device. In doing so you have chosen a
top-quality product. The instructions for use
are to be considered as part of this product. It contains
important safety, assembly and disposal information.
Before using the product, please familiarise yourself
with all the safety information and instructions for use.
The product must only be used as described and for
the specified fields of application. If you pass the prod-
uct on to anyone else, please be sure to also include all
documentation.
Intended use
This product is suitable for lighting the roadway whilst
cycling. The LED Bicycle Light Set is approved as exclu-
sive lighting for all bicycles. Light distribution must not
be impaired by other bicycle parts or luggage. The
product is intended for outdoor use. Any use other than
the aforementioned or any product modification is pro-
hibited and can result in injuries and product damage.
The manufacturer is not liable for damages resulting
from improper use. This product is not intended for
commercial use.
Parts Description
1Headlight bracket
2Reducer rubber
3Headlight bracket retaining screw
4Headlight on/off switch
5Headlight battery/rechargeable battery control light
6Headlight
7Headlight angle adjustment screw
8Headlight lock
9Tail light bracket
10 Tail light lock
11 Tail light bracket rubber tab
12 Tail light on/off switch
13 Tail light battery control lamp
14 Tail light
15 Tail light retaining screw
16 Tail light battery cover
17 USB cable
18 Charging socket
Scope of delivery
1 Headlight
1 Tail light
1 Headlight bracket
1 Tail light bracket
2 Batteries AAA
Reducer rubbers
1 USB cable
1 Instructions for assembly
and use
Technical Data
Headlight
Model designation: XC-195A /LI-1
A B
D
C
ESC F1
~
`
!
1
F2
@
TAB
CAPS
E
3
11
6
1 9 102
4 5
12 13
14
16
7
17
8
18
15
LED BIKE LIGHT SET
LED-FAHRRADLEUCHTEN-SET
Bedienungs- und Sicherheitshinweise
LED BIKE LIGHT SET
Operation and Safety Notes
Model-No. 14129
IAN 278494

DE/AT/CH DE/AT/CH
DE/AT/CH DE/AT/CH
Garantiebedingungen
Die Garantiefrist beginnt mit dem Kaufdatum. Bitte
bewahren Sie den Original-Kassenbon gut auf. Diese
Unterlage wird als Nachweis für den Kauf benötigt. Tritt
innerhalb von drei Jahren ab dem Kaufdatum dieses
Produkts ein Material- oder Fabrikationsfehler auf, wird
das Produkt von uns – nach unserer Wahl – für Sie
kostenlos repariert oder ersetzt. Diese Garantieleistung
setzt voraus, dass innerhalb der Drei-Jahres-Frist das
defekte Gerät und der Kaufbeleg (Kassenbon) vorgelegt
und schriftlich kurz beschrieben wird, worin der Mangel
besteht und wann er aufgetreten ist. Wenn der Defekt
von unserer Garantie gedeckt ist, erhalten Sie das
reparierte oder ein neues Produkt zurück. Mit Reparatur
oder Austausch des Produkts beginnt kein neuer Garantie-
zeitraum. Die Garantiezeit wird durch die Gewährleis-
tung nicht verlängert. Dies gilt auch für ersetzte und
reparierte Teile. Eventuell schon beim Kauf vorhandene
Schäden und Mängel müssen sofort nach dem Auspacken
gemeldet werden. Nach Ablauf der Garantiezeit
anfallende Reparaturen sind kostenpflichtig.
Garantieumfang
Das Gerät wurde nach strengen Qualitätsrichtlinien
sorgfältig produziert und vor Anlieferung gewissenhaft
geprüft. Die Garantieleistung gilt für Material- oder
Fabrikationsfehler. Diese Garantie erstreckt sich nicht
auf Produktteile, die normaler Abnutzung ausgesetzt
sind und daher als Verschleißteile angesehen werden
können oder für Beschädigungen an zerbrechlichen
Teilen, z. B. Schalter, Akkus oder die aus Glas gefertigt
sind. Diese Garantie verfällt, wenn das Produkt beschä-
digt, nicht sachgemäß benutzt oder gewartet wurde.
Für eine sachgemäße Benutzung des Produkts sind alle
in der Bedienungsanleitung aufgeführten Anweisungen
genau einzuhalten. Verwendungszwecke und Handlun-
gen, von denen in der Bedienungsanleitung abgeraten
oder vor denen gewarnt wird, sind unbedingt zu ver-
meiden. Das Produkt ist lediglich für den privaten und
nicht für den gewerblichen Gebrauch bestimmt. Bei
missbräuchlicher und unsachgemäßer Behandlung,
Gewaltanwendung und bei Eingriffen, die nicht von
unserer autorisierten Service-Niederlassung vorgenom-
men wurden, erlischt die Garantie.
Um eine schnelle Bearbeitung Ihres Anliegens zu ge-
währleisten, folgen Sie bitte den folgenden Hinweisen:
· Bitte halten Sie für alle Anfragen den Kassenbon
und die Artikelnummer als Nachweis für den Kauf
bereit.
· Die Artikelnummer entnehmen Sie bitte dem
Typenschild oder dem Titelblatt dieser Anleitung.
· Sollten Funktionsfehler oder sonstige Mängel auf-
treten, kontaktieren Sie bitte zunächst die nachfol-
gend benannte Serviceabteilung telefonisch oder
per E-Mail.
· Ein als defekt erfasstes Produkt können Sie dann
unter Beifügung des Kaufbelegs (Kassenbon) und
Angabe, worin der Mangel besteht und wann er
aufgetreten ist, für Sie portofrei an die Ihnen
mitgeteilte Service-Anschrift übersenden. Bitte
beachten Sie, dass unbedingt vor Versand die
Serviceabteilung informiert werden muss!
Auf www.lidl-service.com können Sie diese und viele
weitere Handbücher, Produktvideos und Software
herunterladen.
KLB GmbH
Diekbree 8, DE-48157 Münster, DEUTSCHLAND
DE
Tel: [phone]
E-Mail: [e-mail]
www.klb-service.eu
AT
Tel: [phone]
E-Mail: [e-mail]
www.klb-service.eu
CH
Tel: [phone]
E-Mail: [e-mail]
www.klb-service.eu
IAN 278494
Scheinwerfer laden (s. Abb. E)
Entfernen Sie die Gummiabdeckung von der Ak-
ku-Ladebuchse 18 und verbinden das USB-Kabel
17 mit der Akku-Ladebuchse 18 .
Anschließend verbinden Sie den USB-Stecker des
USB-Kabels 17 mit einem Computer/Laptop/USB-
Standard-Ladegerät mit 5V DC und 500–1000mA.
Bei Verwendung von Ladegeräten mit anderen
Spezifikationen kann der Akku und damit der
Scheinwerfer beschädigt werden. In diesem Fall
erlischt die Gewährleistung.
Der Scheinwerfer 6verfügt über eine Ladean-
zeige. Leuchtet die Anzeige rot, so sind die Akkus
entladen. Während des Ladevorgangs leuchtet die
Anzeige grün. Sind die Akkus wieder einsatzbereit,
erlischt die Anzeige und Sie können den Schein-
werfer 6benutzen.
Um die volle Leistung der mitgelieferten Akkus zu
erhalten, laden Sie bitte die Akkus beim ersten Mal
nicht kürzer als 10Stunden. Bitte beenden Sie den
Ladevorgang nicht früher, auch wenn die LED be-
reits erloschen ist. Anschließend wird eine Ladezeit
von ca. 3,5 Stunden bei Akkus mit 1300mAh
empfohlen.
Reinigung und Pflege
Die Leuchten niemals komplett unter Wasser tau-
chen. Benutzen Sie keine ätzenden oder scheuern-
den Reinigungsmittel. Hierdurch entstehen
Beschädigungen an den Leuchten.
Reinigen Sie das LED-Fahrradleuchten-Set mit
einem leicht feuchten, fusselfreien Tuch.
Entsorgung
Die Verpackung besteht aus umweltfreundli-
chen Materialien, die Sie über die örtlichen
Recyclingstellen entsorgen können.
Möglichkeiten zur Entsorgung des ausgedienten
Produkts erfahren Sie bei Ihrer Gemeinde oder Stadt-
verwaltung.
Werfen Sie Ihr Produkt, wenn es ausgedient
hat, im Interesse des Umweltschutzes nicht in
den
Hausmüll, sondern führen Sie es einer
fachgerechten
Entsorgung zu. Über Sammel-
stellen und deren Öffnungszeiten können
Sie sich bei Ihrer zuständigen Verwaltung
informieren.
Defekte oder verbrauchte Batterien/Akkus müssen ge-
mäß Richtlinie 2006/66 /EG und deren Änderungen
recycelt werden. Geben Sie Batterien/Akkus und/oder
das Gerät über die angebotenen Sammeleinrichtungen
zurück.
Umweltschäden durch falsche
Entsorgung der Batterien/Akkus!
Batterien/Akkus dürfen nicht über den Hausmüll ent-
sorgt werden. Sie können giftige Schwermetalle enthal-
ten und unterliegen der Sondermüllbehandlung. Die
chemischen Symbole der Schwermetalle sind wie folgt:
Cd = Cadmium, Hg = Quecksilber, Pb = Blei. Geben
Sie deshalb verbrauchte Batterien /Akkus bei einer
kommunalen Sammelstelle ab.
Bei unsachgemäßer Entsorgung der Batterien gehen
wertvolle Ressourcen verloren und durch in den Batte-
rien enthaltene Schadstoffe kann es zu einer erhebli-
chen Gefahr für Gesundheit und Umwelt kommen.
Durch die getrennte Sammlung /Entsorgung von Altbat-
terien werden Gefahren für Gesundheit und Umwelt
vermieden und durch Recycling wertvolle Rohstoffe
zurückgewonnen.
Garantie
Sehr geehrte Kundin, sehr geehrter Kunde,
Sie erhalten auf dieses Gerät 3 Jahre Garantie ab
Kaufdatum. Im Falle von Mängeln dieses Produkts ste-
hen Ihnen gegen den Verkäufer des Produkts gesetzli-
che Rechte zu. Diese gesetzlichen Rechte werden durch
unsere im Folgenden dargestellte Garantie nicht einge-
schränkt.
Bitte beachten Sie, dass nach dem Aufleuchten der
Batterieanzeige die Leuchten nicht mehr der StVZO
entsprechen.
Montage
Scheinwerfer montieren
(s. Abb. A)
Drehen Sie die Halteschraube 3aus dem Halter 1.
Positionieren Sie den Halter 1an der gewünsch-
ten Stelle am Lenker. Verwenden Sie gegebenen-
falls die Reduziergummis 2, um eine optimale
Passform zu gewährleisten.
Drehen Sie die Halteschraube 3wieder ein.
Ziehen Sie dabei die Schraube handfest. Verwen-
den Sie hierzu kein Werkzeug, um Beschädigun-
gen zu vermeiden.
Um den optimalen Winkel zur Fahrtrichtung einzu-
stellen, lösen Sie mit einem Kreuzschraubendreher
die Winkelverstellschraube 7um 2-3 Umdrehungen.
Stellen Sie den gewünschten Winkel ein und zie-
hen die Winkelverstellschraube 7wieder fest.
Schieben Sie den Scheinwerfer 6auf den Halter 1
bis er hörbar einrastet.
Zum Lösen drücken Sie die Scheinwerferarretierung
8und schieben den Scheinwerfer 6vom Halter
1aus nach vorne.
ACHTUNG! Überprüfen Sie regelmäßig die rich-
tige Einstellung Ihres Scheinwerfers. Der Lichtkegel
muss geradeaus in Fahrtrichtung zeigen und darf
nicht zu hoch eingestellt sein, um den Gegenver-
kehr nicht zu blenden.
Rücklicht montieren
(s. Abb. B und C)
Befestigen Sie den Halter 9anhand der Gummi-
lasche 11 an der Sattelstütze oder der Hinterbau-
strebe. Achten Sie dabei darauf, dass sich keine
Gegenstände vor dem Rücklicht 14 befinden.
Ziehen Sie die Gummilasche 11 straff und haken
Sie diese ein.
Lösen Sie die Halteschraube 15 des Halters 9
und stellen Sie den gewünschten Winkel ein.
Anschließend ziehen Sie die Schraube wieder fest.
Ziehen Sie dabei die Schraube handfest. Verwen-
den Sie hierzu kein Werkzeug, um Beschädigun-
gen zu vermeiden.
Schieben Sie das Rücklicht 14 auf den Halter 9
bis er hörbar einrastet.
Zum Lösen des Rücklichts 14 ziehen Sie die Rück-
lichtarretierung 10 nach unten und ziehen das
Rücklicht 14 ab.
ACHTUNG! Das Rücklicht muss so angebaut und
eingestellt werden, dass die Bezugsachse parallel
zur Fahrzeuglängsmittelebene und parallel zur
Fahrbahn liegt.
Batterien ins Rücklicht einlegen
(s. Abb. D)
Schieben Sie den Batteriefachdeckel 16 nach
hinten ab.
Legen Sie die Batterien in das Rücklicht ein
(2x AAA 1,5V). Achten Sie dabei auf die korrekte
Polung.
Setzen Sie anschließend die Leuchte wieder
zusammen.
Bedienung
Ein-/ausschalten
Der Scheinwerfer 6besitzt drei Leuchtstärken.
Ein-/Aus-Schalter
einmal drücken Power Modus (40Lux) für
Fahrten in unbeleuchteter
Umgebung
zweimal drücken Standard Modus (20 Lux)
für Fahrten in beleuchteter
Umgebung
dreimal drücken Eco Modus (10 Lux) für
Fahrten in gut beleuchteter
Umgebung
viermal drücken ausschalten
Technische Daten
Scheinwerfer
Typ-Bezeichnung: XC-195A/LI-1
Nennleistung: 1W
Schutzart: IP44 nach DIN EN 60529
Li-Ion-Akku: 1300mAh, 3,7V
Rücklicht
Typ-Bezeichnung: XC-117D /D-LED 3
Nennleistung: 0,2W
Schutzart: IP44 nach DIN EN 60529
Batterien: 2 x 1,5V AAA LR03
Hinweis: Bitte verwenden Sie bei dem Rücklicht
ausschließlich Akkus mit 1,2V oder vergleichbare
Alkaline-Batterien mit 1,5V.
Sicherheitshinweise
LEBENS- UND
UNFALLGEFAHR FÜR KLEINKIN-
DER UND KINDER! Lassen Sie Kinder
niemals unbeaufsichtigt mit dem Verpackungsmate-
rial, denn es besteht Erstickungsgefahr durch das
Verschlucken von Verpackungsteilen. Kinder unter-
schätzen häufig die Gefahren.
Halten Sie das Produkt stets von Kindern fern. Das
Produkt ist kein Spielzeug!
Dieses Produkt ist nicht dafür bestimmt, durch Perso-
nen (einschließlich Kinder) mit eingeschränkten
physischen, sensorischen oder geistigen Fähigkeiten
oder mangels Erfahrungen bzw. Wissen benutzt zu
werden. Es sei denn, sie werden durch eine für ihre
Sicherheit zuständige Person beaufsichtigt. Beachten
Sie, dass Beschädigungen durch unsachgemäße
Handhabung, Nichtbeachtung der Bedienungsan-
leitung oder Eingriff durch nicht autorisierte Perso-
nen von der Gewährleistung ausgeschlossen sind.
Nehmen Sie das Produkt keinesfalls auseinander.
Durch unsachgemäße Reparaturen können nicht
unerhebliche Gefahren für den Benutzer entstehen.
Lassen Sie Reparaturen nur von Fachkräften durch-
führen. Die LED sind nicht austauschbar.
LEBENS- UND UNFALLGE-
FAHR! Bei Verwendung eines falschen Ladegerä-
tes kann der Scheinwerfer 6beschädigt werden,
überhitzen und sogar explodieren. In diesem Fall
erlischt die Gewährleistung.
Sicherheitshinweise zu
Batterien/Akkus
VORSICHT! EXPLOSIONSGEFAHR!
Laden Sie Batterien niemals wieder auf!
Entfernen Sie bei längerer Nichtverwendung die
Batterien aus dem Produkt.
Achten Sie beim Einlegen auf die richtige Polarität!
Diese wird im Batteriefach angezeigt.
Reinigen Sie Batterie- und Gerätekontakt vor dem
Einlegen falls erforderlich.
Entfernen Sie erschöpfte Batterien umgehend aus
dem Gerät. Es besteht erhöhte Auslaufgefahr!
Tauschen Sie immer alle Batterien gleichzeitig aus.
Verwenden Sie keine Alkalibatterie zusammen mit
einem wiederaufladbaren Akku.
Kombinieren Sie keine neuen Batterien mit alten.
Batterien /Akkus gehören nicht in den Hausmüll!
Jeder Verbraucher ist gesetzlich verpflichtet,
Batterien/Akkus ordnungsgemäß zu entsorgen!
VORSICHT! EXPLOSIONSGEFAHR!
Halten Sie Batterien/Akkus von Kindern
fern, werfen Sie die Batterien/Akkus
nicht ins Feuer, schließen Sie sie nicht kurz und
nehmen Sie sie nicht auseinander.
Bei Nichtbeachtung der Hinweise können die Bat-
terien über ihre Endspannung hinaus entladen wer-
den. Es besteht dann die Gefahr des Auslaufens.
Falls die Batterien in Ihrem Gerät ausgelaufen sein
sollten, entnehmen Sie diese sofort, um Schäden
am Gerät vorzubeugen!
Vermeiden Sie Kontakt mit Haut, Augen und
Schleimhäuten, falls Flüssigkeit aus den Batterien /
Akkus ausgetreten ist. Spülen Sie bei Kontakt mit
Batteriesäure die betroffenen Stellen sofort mit
reichlich klarem Wasser und suchen Sie umgehend
einen Arzt auf.
Batterien niemals wieder aufladen! Explosionsgefahr!
Hinweis: Leuchtet die rote Akku-/Batterie-Kontroll-
leuchte 513 im Scheinwerfer 6oder im Rück-
licht 14 auf, so ersetzen Sie bitte die Batterien bzw.
laden die Akkus wieder umgehend auf.
Legende der verwendeten Piktogramme
Anweisungen lesen!
Lebens- und Unfallgefahr für
Kleinkinder und Kinder!
Warn- und Sicherheitshinweise
beachten!
Vorsicht! Explosionsgefahr!
Grüner Punkt - Recycling von
Verpackungen.
Symbol zur Erkennung von Elektro-
und Elektronikgeräten.
Umweltschäden durch falsche
Entsorgung der Batterien/Akkus!
USB – Universal Serial Bus – Verbin-
dungsstelle zum Anschluss z. B. an einen
Computer (nur aufladen).
K XXXXX
Prüfzeichen des Kraftfahrt-Bundesamtes
(K mit nachfolgender Zulassungsnummer).
Produkte und Verpackungen sollen
umweltschonend entsorgt werden.
21
PAP
Recycling-Code zur Entsorgung von
Pappe.
LED-Fahrradleuchten-Set
Einleitung
Herzlichen Glückwunsch zum Kauf Ihres
neuen Gerätes. Sie haben sich damit für ein
hochwertiges Produkt entschieden. Die Bedie-
nungsanleitung ist Bestandteil dieses Produktes. Sie ent-
hält wichtige Hinweise zur Sicherheit, Montage und
Entsorgung. Machen Sie sich vor der Benutzung des
Produktes mit allen Bedien- und Sicherheitshinweisen
vertraut. Benutzen Sie das Produkt nur wie beschrieben
und für die angegebenen Einsatzbereiche. Händigen
Sie alle Unterlagen bei Weitergabe des Produktes an
Dritte mit aus.
Bestimmungsgemäße
Verwendung
Das Produkt ist zur Fahrbahnausleuchtung beim Fahr-
radfahren geeignet. Das LED-Fahrradleuchten-Set ist für
alle Fahrräder als alleinige Beleuchtung zugelassen.
Die Lichtverteilung darf durch keine anderen Fahrrad-
teile oder Gepäckstücke behindert werden. Das Pro-
dukt ist zur Anwendung im Außenbereich bestimmt.
Eine andere Verwendung als zuvor beschrieben oder
eine Veränderung des Produktes ist nicht zulässig und
kann zu Verletzungen und Beschädigungen des Produk-
tes führen. Für aus unsachgemäßer Verwendung ent-
standene Schäden übernimmt der Hersteller keine
Haftung. Das Produkt ist nicht für den gewerblichen Ein-
satz bestimmt.
Teilebeschreibung
1Halter Scheinwerfer
2Reduziergummis
3Halteschraube Scheinwerferhalter
4Ein-/Aus-Schalter Scheinwerfer
5Akku-/Batterie-Kontrollleuchte Scheinwerfer
6Scheinwerfer
7Winkelverstellschraube Scheinwerfer
8Scheinwerferarretierung
9Halter Rücklicht
10 Rücklichtarretierung
11 Gummilasche Halter Rücklicht
12 Ein-/Aus-Schalter Rücklicht
13 Batterie-Kontrollleuchte Rücklicht
14 Rücklicht
15 Halteschraube Rücklichthalter
16 Batteriefachdeckel Rücklicht
17 USB-Kabel
18 Akku-Ladebuchse
Lieferumfang
1 Scheinwerfer
1 Rücklicht
1 Halter Scheinwerfer
1 Halter Rücklicht
2 Batterien AAA
Reduziergummis
1 USB-Kabel
1 Montage- und
Bedienungsanleitung
GB/IE/NI
DE/AT/CH
damage to fragile parts, e.g. switches, rechargeable
batteries, or made from glass. This warranty becomes
void if the device has been damaged or improperly
used or maintained. Proper use of the product requires
strictly observing all instructions for use. Purposes and
practices which the operating instructions warn of or
advise against must be avoided without fail. This prod-
uct is only intended for private, non-commercial use.
Any incorrect or improper use of the device, use of
force and changes not performed by our authorized
service branch will void the warranty.
Please follow the instructions below to ensure your
claim is processed quickly:
· Please have your receipt and the product number
ready as your proof of purchase.
· Please refer to the type plate or the cover sheet of
these instructions for the product number.
· In the event of malfunctions or other defects,
please first contact the following service depart-
ment by phone or e-mail.
· A product determined defective may then be
returned to the specified service address free of
charge, including the proof of purchase (receipt)
and information about the defect and when it
occurred.
Please note, the service department must be
notified before returning the product!
This and many other manuals, product videos and
software are available for download at
www.lidl-service.com.
GB
KLB GmbH
Diekbree 8
DE-48157 Münster, GERMANY
Tel: [phone]
E-Mail: [e-mail]
www.klb-service.eu
IE
KLB GmbH
Diekbree 8
DE-48157 Münster, GERMANY
Tel: [phone]
E-Mail: [e-mail]
www.klb-service.eu
NI
KLB GmbH
Diekbree 8
DE-48157 Münster, GERMANY
Tel: [phone]
E-Mail: [e-mail]
www.klb-service.eu
IAN 278494
KLB GMBH
Diekbree 8
DE-48157 Münster, GERMANY
Last Information Update · Stand
der Informationen: 10/2016
Ident.-No.: 14129102016-GB/IE/NI