Crosswater Belgravia US-BL002 User manual

Installation Instructions
27-7/8"
7"
3-1/8"
1/2” NPSM
Tape
measure
Safety
glasses
Set
square
Pencil Spirit
level
Silicone
sealant
Tools required
DimensionsIntroduction
The floor-standing legs have been fully inspected throughout the
production process and only leaves our factory after a 15-step QC
process.
Carefully remove the floor-standing legs from the box and check that
all parts have been supplied.
Before beginning installation, please check for any damage that may
have occurred during transport. Note: Damage claims cannot be
made during or after installation.
Improper installation shall result in loss of warranty in case of damage
caused by impacts or rubbing against rough surfaces.
Prior to installing the floor-standing legs prepare a connection of water
inlet/outlet.
The customer may choose the type and location of the faucet,
installation instructions should be supplied by the faucet manufacturer.
IMPORTANT: Please read these instructions carefully before
beginning and retain for future reference.
We do not accept responsibility for any problems that may occur
through incorrect installation.
Belgravia Floor-standing Pillar Legs
US-BL002
Installation notes
The installation must comply with all plumbing codes including local
codes and be installed by a licensed plumbing contractor.
Anti-scald protection is the responsibility of the installer and
according to applicable codes.
Install US-AA002ROUGH first using the instructions provided with
it.
IMPORTANT! Before installing a new faucet it is essential that the
supply pipes are thoroughly flushed in order to remove any remaining
debris, solder or other impurities. Failure to carry out this simple
procedure can cause problems or damage to the working of the
faucet. Installing shut-off valves on incoming supply lines is
recommended for ease of maintenance.
Turn off the main water supply before connecting to any existing
pipework or doing any maintenance.
WARNING! Please check for any hidden pipes and cables, electric
or otherwise, before drilling holes in a wall or floor.

11/
2
” - 15/
8
”
Pre-installed US-AA002ROUGH
Floor
GASKET
x2
SET SCREW
x4
COLLAR
x2
TUBE
x2
SUPPORT
x2
STEEL BRAIDED
HOSE
x2
COLLAR FIXING
SCREWS
x6
SUPPORT
SCREWS
x8
US-AA002ROUGH
Installation
lShut off the water heating system then, with the main water supply
turned o, open the lowest hot and cold faucets and allow to drain
until supply pipes are empty.
lIdentify all components before fitting.
lBefore installing the floor-standing legs, it is necessary to install the
US-AA002ROUGH first. Follow the instructions supplied with it,
making sure the distance between floor and the bottom of the
rough is between 1-1/2” and 1-5/8”.
lInstall the floor-standing legs as per the detailed instructions that
follow.
lOnce the floor-standing legs are installed, connect the chosen
faucet.
ATTENTION:Check all new connections for leaks.
lTurn on the main water supply, close all faucets except for the new
installed faucet and as the system refills, check for leaks.
lOnce satisfied there are no leaks, switch on the heating system.
Parts list

HEIGHT ADJUSTEMT
SCREWS
FIXING SCREWS
Installation
lInstall the supports onto the rough. Line up the fixing screws and
ensure the small screw hole is facing the front, as shown opposite.
lThere are 4 height adjustment screws located in the support. Use
these to set the desired height of the support.
lSecure with the fixing bolts.
lConnect the steel braided hose onto the rough outlets.
lInstall the collar using the fixing screws supplied.
lSlide the steel braided hose through the tube.
lSlide the gasket onto the leg of the mixer.
lConnect the hose onto the leg of the mixer.
lPull the tube up tight against the gasket, then secure with the set
screw through the gasket.

Issue date: 15092019
Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.
For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757
Toll free number: 844-XWATER-1 (844-992-8371) tel: [phone] fax: [phone]
www.crosswaterlondon.com
email: [e-mail]
Rinse away any traces of soap and gently dry with a clean, soft
cloth after each use. Rinse completely with water and dry any
overspray. This will maintain the finish and avoid water spotting.
To remove mineral deposits, use a 50/50 solution of white vinegar
and water. Do not allow the solution to soak on the product.
Simichrome Polish® contains a protective film to enhance
maintenance and is helpful in preventing water spot buildup.
Follow instructions to ensure optimum results.
Never use an abrasive material such as a brush or scouring pad to
clean the surface. The use of abrasive cleaners, cleansers or
disinfectants will alter the surface finish and void the warranty.
Do not allow certain materials such as toothpaste, cologne,
shaving cream, nail polish remover, vinegar, wine, drain and glass
cleaners to remain on the surface. Prolonged contact will alter
surface finishes and void the warranty.
We DO NOT recommend using any household cleaners as
many can cause damage to the finish.
Please see the website for care instructions for specific finishes.
 Cleaning Instructions
Installation
lPush the tube fully down onto the collar, as shown
opposite.
lSecure with the set screw through the collar.