CYBEX Eagle Leg Press 11040 User manual

Cybex Eagle®Leg Press
Medical Owner’s Manual
Strength Systems
Part Number 11040-888-4
www.cybexinternational.com

Cybex Eagle®Leg Press
Medical Owner’s Manual
Strength Systems
Cybex®and the Cybex logo are registered trademarks of Cybex International, Inc.
Eagle®and its mark are registered trademarks of Cybex International, Inc.
DISCLAIMER: Cybex International, Inc., makes no representations or warranties regarding the contents of this manual. We reserve the right to
revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such
revisions or changes.
© Copyright 2010, Cybex International, Inc. All rights reserved.
Printed in the United States of America.
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX [phone]
www.cybexinternational.com • [email protected] • May 2010

1 Safety
Safety ......................... 1-1
Safety Guidelines and Practices . . . . 1-2
Warning/Caution Decals .......... 1-3
Regular Maintenance Activities..... 1-6
Using Proper Form . . . . . . . . . . . . . . 1-6
2 Exercises
Intended Use . . . . . . . . . . . . . . . . . . 2-1
Instructions . . . . . . . . . . . . . . . . . . 2-2
3 Customer Service
Contacting Service .............. 3-1
4 Maintenance
Daily Procedures ................ 4-1
Weekly Procedures .............. 4-2
Yearly Procedures ............... 4-4
Environment. . . . . . . . . . . . . . . . . . . 4-5
Storage . . . . . . . . . . . . . . . . . . . . . . 4-5
Table of Contents
Page i

1-1
Safety
This product complies with the European Medica Directive 93/42/EEC.
Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
It is the responsibility of the facility owner and/or owner of the equipment to instruct users on proper operation of the
equipment and review all labels.
WARNING: Serious injury could occur if these safety precautions are not observed:
User Safety Precautions
• Follow advice of medical staff prior to beginning an exercise program.
• If a user has special needs (such as medical rehabilitation or disability) it is essential that the owner (person
with legal responsiblity) conducts a specic risk assessment to determine safe use and if necessary trained
staff are available to supervise the activity.
• Injuries to health may result from incorrect or excessive training.
• Read and understand warning labels and user manual prior to exercising. Obtain instruction prior to use.
• Keep body and clothing free from and clear of all moving parts.
• Inspect machine prior to use. DO NOT use if it appears damaged or inoperable.
• DO NOT attempt to x a broken or jammed machine. Notify oor staff.
• Use this machine only for the intended use. DO NOT modify the machine.
• Be sure that the weight pin is completely inserted. Use only the pin provided by the manufacturer. If unsure,
seek assistance.
• Never pin the weights in an elevated position. DO NOT use the machine if found in this condition. Seek
assistance from oor staff.
• The intended use is not for children. Keep all children (12 and under) away. Teenagers (13 and over) must
be supervised.
• DO NOT use if guards are missing or damaged.
• DO NOT use dumbbells or other incremental weights, except those provided by the manufacturer.
• Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed or
damaged.
• DO NOT remove any labeling from equipment. Replace any damaged labels
• Stop exercising if you feel faith, dizzy or experience pain at any time while exercising and consult your
physician.
1 - Safety

1-2
Facility Safety Precautions
• Read the Owner’s Manual carefully before assembling, servicing or using the equipment.
• Securely anchor each machine to the oor using the anchor holes provided in each machine.
NOTE: Cybex is not responsible for the actual anchoring of equipment. Consult with a professional contractor.
NOTE: Use fasteners having a minimum of 2,200 newtons tensile capacity (3/8” grade 2 bolts or better).
NOTE: If legs/frame does not contact surface, DO NOT pull down with anchors. Shim any
leg or frame not in contact with surface using at washers.
• Make sure that each machine is set up and operated on a solid level surface. Do not install equipment on an
uneven surface.
• Make sure that all users are properly trained on how to use the equipment and proper supervision based on individual
indiciation is provided.
• Make sure there is enough room for safe access and operation of the equipment. NOTE: At least one meter around
machine when in exercise position.
• Perform mandatory safety inspections. Perform regular maintenance checks on the equipment. Also pay close atten-
tion to all areas most susceptible to wear, including (but not limited to) cables, pulleys, belts and grips.
• Immediately replace worn or damaged components. If unable to immediately replace worn or damaged components
then remove from service until the repair is made.
• Use only Cybex supplied components to maintain/repair the equipment.
• Keep a repair log of all maintenance activities.
• Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed or
damaged.
NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular maintenance is performed.
NOTE: Check range of movement of patient carefully before using equipment. Select resistance according to the
individual indication. If you are unsure then start at lowest level. Perform exercise using smooth controlled
movements.
Safety Guidelines And Practices
Cybex recommends that all training equipment be used in a supervised area. It is recommended that the equipment be
located in an access controlled area. Control is the responsibility of the owner. The extent of control is at the discretion of
the owner.
It is the responsibility of the purchaser/user of Cybex products to read and understand the owner’s manual, and warning
labels; as well as instruct all individuals, whether end users or supervising personnel, on proper usage of the equipment.
PROPER USAGE:
Use machine only as described in the manual. Failing to follow proper instructions may result in injury.
Do Not Lean Against or Pull On the framework, weight stack, or any component, whether machine is at rest or in use.
Inappropriate or improper use may result in injury to users or third parties (bystanders).
Do not use machine if it is not located on a solid level surface or is improperly installed.
Provide an adequate safety perimeter between the machine, walls and other equipment to ensure that the facility has the
proper clearance for usage and training.

1-3
SECURING EQUIPMENT:
The machine has holes in the feet, which allow for ease in anchoring to the oor. Cybex strongly recommends that, to
eliminate rocking, tipping or falling over due to incorrect usage and misuse, equipment be secured to a solid, level surface.
1. The solid, level surface should not deviate more than 1/8” over a 10’ distance or as dened and required by local
building and architectural codes.
2. Anchoring of equipment must be completed by a qualied licensed contractor.
3. Anchoring holes are provided on the feet of the frame. All anchoring locations must be used when anchoring the
equipment to the oor.
4. Due to the wide variation of ooring on which machines may be anchored or installed, verify anchoring method and
anchoring fasteners with a qualied and licensed contractor.
5. A minimum pull out force of 220 lbs/100 kgs is required for each anchor position..
6. Do not use machine until it is properly anchored.
MAINTENANCE:
Preventative maintenance allows proper equipment operation and reduces the risk of injury. Perform the maintenance
requirements as specied in the manual.
STANDARD COMPLIANCE:
Cybex products meet or exceed applicable ASTM and EN Standards.
Warning/Caution Decals
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Caution decals indicate a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury.
The warning and caution decals are shown on the following page. The diagrams following the decals show where each
decal is located.

1-4
125
1:1
OWATONNA
MFG. APPR.
TECH. PUBS. APPR. DATE
DATE
REV.
DWG. NO.
SCALE
SIZE
CHECKED BY
DWG. BY
TITLE:
FINISH:
MATERIAL:
B
SHEET
OF
1 1
EXCEPT AS NOTED
GENERAL
TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015
ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR
PARALLEL SHALL BE
SO WITHIN ± 1°
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
SURFACE FINISH
INDICATED PER
ANSI B46.1-1985
GENERAL
MACHINING
DIMENSIONS
IN INCHES
DATE
DATE
REMOVE CARBURIZATION
AND SCALE FROM LASER
AND PLASMA CUT EDGES
B
WARNING DECAL, ENGLISH
4605-381-4
EML 3/26/2007
NOTE: See Engineering Drawing 4506-381-X for specifications.
ALL MATERIAL MUST COMPLY TO
EUROPEAN UNION DIRECTIVE
2002/95/EC RoHS (RESTRICTION
OF HAZARDOUS SUBSTANCES)
4605-381-4 B
WARNING
SERIOUS INJURY COULD OCCUR IF THESE PRECAUTIONS ARE NOT OBSERVED
2. Read and understand warning labels and user manual prior to exercising. Obtain instruction prior to use.
1. Obtain a medical exam prior to beginning an exercise program.
3. Keep body and clothing free from and clear of all moving parts.
4. Inspect machine prior to use. DO NOT use if it appears damaged or inoperable.
5. DO NOT attempt to fix a broken or jammed machine. Notify floor staff.
6. Use the machine only for the intended use. DO NOT modify the machine. 7. Be sure that the weight pin is completely inserted. Use only the pin provided by the manufacturer. If unsure seek assistance.
8. Never pin the weights in an elevated position. DO NOT use the machine if found in this condition. Seek assistance from floor staff.
9. Children must not be allowed near this machine. Teenagers must be supervised.
10. DO NOT use if guards are missing or damaged. 11. DO NOT use dumbbells or other incremental weights, except those provided by the manufacturer. 12. Inspect all cables and belts and connections prior to use. DO NOT use if any components are worn, frayed, or damaged. 13. DO NOT REMOVE THIS LABEL. REPLACE IF DAMAGED.
2.25
R .19 4 PLACES
PART NUMBER WITH REVISION DESIGNATION 7 PT ARIAL
12 PT ARIAL FONT
R .25 4 PLACES
INSET .06 WHITE
SAFETY ORANGE PMS 152 BLACK TRIANGLE W/ ORANGE EXCLAMATION POINT, BLACK LETTERS 23 PT ARIAL BOLD FONT
8.00
8.25 PT ARIAL FONT
WHITE BACKGROUND BLACK LETTERS
A
Personal injury may occur.
CAUTION
4000Y316-4 A
2.50
1.50
R .19
4 PLACES
PART NUMBER
6 PT ARIAL BOLD
WHITE BACKGROUND WITH
BLACK 11.5 PT ARIAL BOLD TEXT
SAFETY YELLOW PMS 108
BACKGROUND. BLACK TRIANGLE
W/ YELLOW EXCLAMATION POINT,
BLACK LETTERS 26 PT ARIAL
BOLD FONT
INSET .06
WHITE
Keep away from moving
parts to avoid injury.
DECAL, CAUTION ENGLISH
4000Y316-4
JKW 8/28/06
A
8/28/06
BB
125
1:1
OWATONNA
MFG. APPR.
TECH. PUBS. APPR. DATE
DATE
REV.
DWG. NO.
SCALE
SIZE
CHECKED BY
DWG. BY
TITLE:
FINISH:
MATERIAL:
B
SHEET
OF
1 1
EXCEPT AS NOTED
GENERAL
TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015
ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR
PARALLEL SHALL BE
SO WITHIN ± 1°
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
SURFACE FINISH
INDICATED PER
ANSI B46.1-1985
GENERAL
MACHINING
DIMENSIONS
IN INCHES
DATE
DATE
THIS NOTE REFERS TO ALL PLASTIC PARTS
AND ASSEMBLIES CONTAINING PLASTICS.
RAW MATERIAL AND COMPONENTS ON
SUB-ASSEMBLIES AND ASSEMBLIES MUST
COMPLY WITH EUROPEAN DIRECTIVE
RoHS 2002/95/EC.
REMOVE CARBURIZATION
AND SCALE FROM LASER
AND PLASMA CUT EDGES
NOTE: See Engineering Drawing 4000Y316-X for specifications.
Personal injury may occur.
CAUTION
4000Y316-4 A
Keep away from moving
parts to avoid injury.
125
1:1
OWATONNA
MFG. APPR.
TECH. PUBS. APPR. DATE
DATE
REV.
DWG. NO.
SCALE
SIZE
CHECKED BY
DWG. BY
TITLE:
FINISH:
MATERIAL:
B
SHEET
OF
1 1
EXCEPT AS NOTED
GENERAL
TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015
ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR
PARALLEL SHALL BE
SO WITHIN ± 1°
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
SURFACE FINISH
INDICATED PER
ANSI B46.1-1985
GENERAL
MACHINING
DIMENSIONS
IN INCHES
DATE
DATE
REMOVE CARBURIZATION
AND SCALE FROM LASER
AND PLASMA CUT EDGES
DECAL, CAUTION ENGLISH
8500-026-4 A
JKW 8/31/06 BB 12-13-06
NOTE: See Engineering Drawing 8500-025-X for specifications
2.00 R .19
4 PLACES
2.875
PART NUMBER
8 PT ARIAL BOLD
WHITE BACKGROUND WITH
BLACK 9.5 PT ARIAL BOLD TEXT
SAFETY YELLOW MUNSELL 5Y8/12
BACKGROUND. BLACK TRIANGLE
W/ YELLOW EXCLAMATION POINT,
BLACK LETTERS 21 PT ARIAL
BOLD FONT
INSET .06
WHITE
CAUTION
Keep away from moving
parts. Failure to do so could
result in personal injury.
8500-026-4 A
CAUTION
ALL MATERIAL MUST COMPLY TO
EUROPEAN UNION DIRECTIVE
2002/95/EC RoHS (RESTRICTION
OF HAZARDOUS SUBSTANCES)
B
D
JKW 8/16/2006 BB 10-18-06
125
1:1
OWATONNA
MFG. APPR.
TECH. PUBS. APPR. DATE
DATE
REV.
DWG. NO.
SCALE
SIZE
CHECKED BY
DWG. BY
TITLE:
FINISH:
MATERIAL:
B
SHEET
OF
1 1
EXCEPT AS NOTED
GENERAL
TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015
ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR
PARALLEL SHALL BE
SO WITHIN ± 1°
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
SURFACE FINISH
INDICATED PER
ANSI B46.1-1985
GENERAL
MACHINING
DIMENSIONS
IN INCHES
DATE
DATE
REMOVE CARBURIZATION
AND SCALE FROM LASER
AND PLASMA CUT EDGES
CAUTION DECAL ENGLISH
8500-025-4 A
NOTE: See Engineering Drawing 8500-025-X for specifications
1.75
1.75
R .19
4 PLACES
PART NUMBER
6 PT ARIAL BOLD
WHITE BACKGROUND WITH
BLACK 10 PT ARIAL BOLD TEXT.
SAFETY YELLOW PMS 108
BACKGROUND. BLACK TRIANGLE
W/ YELLOW EXCLAMATION POINT,
BLACK LETTERS 18 PT ARIAL BOLD
TEXT.
INSET .06
WHITE
8500-025-4 A
Failure to correctly
adjust could result in
personal injury.
Always fully engage
the detent pin before
use to avoid injury.
CAUTION
ALL MATERIAL MUST COMPLY TO
EUROPEAN UNION DIRECTIVE
2002/95/EC RoHS (RESTRICTION
OF HAZARDOUS SUBSTANCES)
C
JKW/BG 1/06/09 BB 4/24/09
125
1:1
OWATONNA
MFG. APPR.
TECH. PUBS. APPR. DATE
DATE
REV.
DWG. NO.
SCALE
SIZE
CHECKED BY
DWG. BY
TITLE:
FINISH:
MATERIAL:
B
SHEET
OF
1 1
EXCEPT AS NOTED
GENERAL
TOLERANCES:
2 DECIMALS ± .03
3 DECIMALS ± .015
ANGLES ± 1°
FEATURES SHOWN
PERPENDICULAR OR
PARALLEL SHALL BE
SO WITHIN ± 1°
REMOVE ALL BURRS
BREAK SHARP EDGES
.005/.010 R
SURFACE FINISH
INDICATED PER
ANSI B46.1-1985
GENERAL
MACHINING
DIMENSIONS
IN INCHES
DATE
DATE
THIS NOTE REFERS TO ALL PLASTIC PARTS
AND ASSEMBLIES CONTAINING PLASTICS.
RAW MATERIAL AND COMPONENTS ON
SUB-ASSEMBLIES AND ASSEMBLIES MUST
COMPLY WITH EUROPEAN DIRECTIVE
RoHS 2002/95/EC.
REMOVE CARBURIZATION
AND SCALE FROM LASER
AND PLASMA CUT EDGES
CAUTION DECAL ENGLISH
8500-028-4 A
NOTE: See Engineering Drawing 8500-028-X
4.00
1.75
R .19
4 PLACES
INSET .06
WHITE
PART NUMBER
8 PT ARIAL BOLD
WHITE BACKGROUND WITH
BLACK 10 PT ARIAL BOLD TEXT
Back cushion may drop when knob is pulled. Support
back cushion while adjusting.
SAFETY YELLOW PMS 108
BACKGROUND. BLACK TRIANGLE
W/YELLOW EXCLAMATION POINT,
BLACK LETTERS 24 PT. ARIAL BOLD TEXT.
CAUTION
Be sure detent pin is fully engaged before use. Return
back cushion to lowest position when not in use.
Failure to do so could result in personal injury.
8500-028-4 A
Specs Master Artwork
BB 4/24/09
E

1-5
Leg Press - 11040
ITEM NO. QTY. PART NUMBER DESCRIPTION
111 4 HT572512
TAP SC NO. 10-24 X .50 PN HD PHIL
110 4 HN575100 LOCKNUT .190-No 10-24
109111040-769 EAGLE PLAQUE
108112040-357 PIN, DETENT
1074JC620415
BHSCS .250-20 X .75
106211000-384 BLOCK, STOP
105211040-568
CLAMP BLOCK INSERT
1044JS347400 LOCKWASHER, INT TOOTH .375
103111040-566 DECAL, SEAT ADJUSTING
1022WW150003 WHEEL, 4.00 DIA.
1011PU060201 BUMPER
100 A/R PR400202
GRIP 1.38 OD X .96 ID
99 A/R PR250203 STRIP, FOAM .12 X .25 X ROLL
98 2 PR069400 BUMPER, RECESS
97 2 PR060005 BUMPER, WEIGHT
96 2 PP090208
INSERT, PLASTIC 1.75 DIA. RIBBED
95 1 PP090202 INSERT, PLASTIC 1.50 x 3.00 x 11 GA
94 2 JD343331 S BOLT .500 X 3.50 .375-16
93 6 JC700420 BHSCS .375-16 X 1.25
92 4 JC780417 BHSCS .500-13 X 1.00
91 16 JC700412 BHSCS .375-16 X .50
90 2 JC660412 BHSCS .312-18 X .50
89 2 JC620422 BHSCS .250-20 x 1.50
88 2 JC620412 BHSCS .250-20 X .50
87 8 HY740000 SET SCREW
86 2 HX-60184
BALL STUD, .312 - 18 UNC x 10 mm
85 23 HT542514
PN HD PHIL SC # 8 X .625 BLK
84 4 HT102214 PHIL, HEX, WASHER HD, TYPE 23, 10-24
83 2 HS407100 WASHER, SPRING .650 ID x .790 OD x .062 THK
82 4 HS387300 LOCKWASHER EXT. TOOTH .500
81 18 HS347600 WASHER, SAE .375
80 21 HN704901 LOCKNUT, .375-16 NYLON
79 2 HN-60065 NUT, HEX SELF- LOCKING .312-18 BLK ZINC
78 15 HF540200 GROMMET, NYLON
77 2 HF449063
INSERT 3/4 X 1/4-20
76 4 HC700432 BHSCS .375-16 X 2.75
75 11 HC700430 BHSCS .375-16 X 2.50
74 2 HC700428 BHSCS .375-16 X 2.25
73 4 HC700416 BHSCS .375-16 X .875
72 4 HC700415 BHSCS .375-16 X .75
71 2 HC620414 BHSCS .250-20 X .625
ITEM NO. QTY. PART NUMBER DESCRIPTION
70 1 GP000212 PULLEY ASSEMBLY-3.50
69 4 GP000209 PULLEY ASSEMBLY-3.50
68 A/R GB000202
BELT .95 WIDE
67 4 FS110200 SEAL, LINEAR BEARING
66 6 FB130207 BRG FLG 17mm X 19mm X 25mm
65 4 FB110200 BRG, LINEAR 1.50
64 10 FB030232 BEARING, RADIAL 17 mm EXTENDED RACE
63 1 CM000211 DECAL, PATENT PENDING
62 2 BS070201 COM SPRING .56 x .66 1.50 LG
61 4 BR030214 RETAINING RING, .625 DIA
60 2 br030212 RETAINING RING, 1.575 INTERNAL
59 2 BR030210 RETAINING RING, 17mm
58 4 BR030203 RETAINING RING
57 29100-315
CLIP, DAMPNER SAFETY
56 19100-314 CYLINDER, DAMPNER
55 1 8500-028 DECAL, CAUTION
54 2 8500-026 DECAL, CAUTION
53 1 8500-025 DECAL, CAUTION
52 151198
WARRANTY BOOKLET (NOT SHOWN)
51 1 4605-511INSERT,PLASTIC 5.94
50 1 4605-322 PIN, DETENT
49 2 4505-331
BUMPER, 1.50 DIA
48 44000Y316 DECAL, CAUTION
47 1 4605-381 WARNING LABEL
46 1 3900-441
DECAL, CYBEX INTERNATIONAL
45 5 11090-392 FOOT COVER
44 2 11090-376
RING, HANDLE GRIP
43 2 11090-374 END CAP
42 2 11090-369 SHAFT, PIVOT
41 2 11080-337 SHAFT PIVOT
40 2 11050-375
PIVOT PIN
39 1 11040-999 EAGLE LEG PRESS INSTALLATION INSTR.
38 1 11040-610-4 PLACARD, EAGLE LEG PRESS
37 1 11040-563 SHIELD
36 1 11040-562 NON-SLIP
35 1 11040-561
DECAL, WEIGHT PLATE (310 - 490)
34 1 11040-560 DECAL, WEIGHT PLATE (10 - 290)
33 2 11040-557 P/SPACER
32 2 11040-554 GLIDE
31 1 11040-553 HANDLE SHAFT
30 1 11040-551 DECAL, ADJUSTING
29 2 11040-531
WT ROD .625 DIA X 64.50
28 1 11040-530 SHAFT, PIVOT
27 1 11040-529 SHAFT, PIVOT
26 2 11040-499 P/CHANNEL
25 1 11040-761
PANEL, SHROUD BACK
24 2 11040-763 PANEL, SHROUD FRONT
23 2 11040-777 TRAY, BOTTOM
22 2 11040-776 CHASSIS
21 1 11040-768 COVER, TOP
20 1 11040-770 COVER, TOP
19 2 11040-753
EXT INC WT CHANNEL
18 2 11040-755 EXTRUDED GUARD
17 2 11040-752
EXT INC WT CHANNEL
16 2 11040-440 KNOB
15 2 11040-344 SHAFT
14 1 11040-321 P/ADJUSTING ARM
13 1 11040-301
CLAMP BLOCK INSERT
12 2 11040-225 COATED BEARING HOUSING
11 1 11040-227 P/ADJUSTING BAR
10 1 11040-222
W/OUTER ADJUSTING TUBE
9111040-220 W/FRAME
8111040-219W/PIVOT
7111040-218W/CAM
6111040-215W/PIVOT
5111040-213W/FRAME
4111040-206W/CUSHION PLATE
3111040-205W/SEAT
2111040-203W/LINKAGE
1111040-202W/FOOT PLATE
D
B
B
A
B
D
C
E
A. Warning Label...................4605-381-4
B. Caution Decal ...................4000Y316-4
C. Caution Decal ...................8500-025-4
D. Caution Decal ...................8500-026-4
E. Caution Decal................... 8500-028-4
DESCRIPTION PART NO.

1-6
Regular Maintenance Activities
Preventative maintenance activities must be performed to maintain normal operation of your equipment.
Keeping a log sheet of all maintenance actions will assist you in staying current with all preventative
maintenance activities. The preventative maintenance actions are described in detail in Chapter 4.
Briey, they include:
Daily
1. Clean upholstery.
Weekly
1. Inspect all nuts and bolts for looseness. Tighten as required.
2. Inspect all cables and belts for damage or wear (see Chapter 4). If a cable or belt is worn
or damaged, immediately discontinue use until cable or belt has been replaced.
3. Check for worn handles, worn snap links, and worn warning labeling. Replace all worn parts
immediately.
4. Inspect for loose or worn grips. Replace all worn grips immediately.
5. Inspect weight stacks for proper alignment and operation. Correct all improper alignment
and operation issues immediately.
6. Lubricate guide rods using automotive engine oil only.
Yearly
1. Replace all cables and belts at least annually.
Using Proper Form
Before working out, read and understand the exercises located on the placard and in Chapter 2.

2-1
2 - Exercise
Intended Use
This equipment is suitable for treatment of patients
with illness or injuries and for prevention. This
equipment does not possess any measurement
functions.
This equipment is only intended to be operated for use
under the supervision of a physician, physiotherapist
who has the requisite training and instruction.
The use of this equipment is the responsibility of the
physician or trained medical expert.
NOTE: Do not turn knob when weight stack is elevated.
NOTE: All adjustment points on the machine have yellow handles or knobs.
Quadriceps, Gluteus Maximus
Hamstings
MUSCLES USED
START FINISH
NOTE: Motion Developed: Hip Extension, Knee Extension

2-2
Instructions
Set Up
1. Adjust back to desired angle.
2. Adjust foot plate to desired start position of about 90 degrees at the knee.
3. Position feet on foot plate shoulder width apart and toes pointed slightly outward.
Movement
1. Press shoulders and back into back pad by extending legs. NOTE. Do not hyperextend knees.
Indications:
This machine is used for muscle training or physical rehabilitation and preventive health training only.
Equipment may only be used under supervision of an authorized trainer.
A patient needs to be capable of a full motion range.
The machine is not intended for any exercises other than the ones shown in the short instruction decal on the
machine.
Contraindications:
The following conditions must be cleared by a physician beforehand: fractures, recent operations, severe
osteoporosis with less than 80% bone density, acute herniated disc with surgical indication, tumors and severe
circulatory or vascular illnesses and pulmonary functional disruptions, asthma, severe diabetes, pregnancy shortly
before delivery, detached retina.
Equipment without motion limiters may only be used by patients capable of full range of motion. The equipment is not
sterile and should not be used by patients with contagious diseases or open wounds.
If weakness, dizziness or pain occurs during training, stop the training and consult your physician.
Un-controlled or forced training can lead to pain/physical overloading. Only adjust the settings/weight intensity/number
of repetitions after talking with your trainer.
Training may only be carried out after a prior instruction session by a qualied person.

3-1
3 - Customer Service
Contacting Service
SCHWEIZ
Leuenberger Medizintechnik AG
Industriestr. 19
CH-8304 Wallisellen
Tel.: [phone]
Fax: [phone]
Chemin du Croset 9 B
CH-1024 Ecublens
Tél.: [phone]
Fax: [phone]
[email protected]
DEUTSCHLAND
LMT Deutschland AG
Stuttgarter Strasse 57
D-74321 Bietigheim-Bissingen
Tel.: [phone]
Fax: [phone]
[email protected]
ÖSTERREICH
LMT CYBEX GmbH
Anton Hanakgasse 5
A-2103 Langenzersdorf
Tel.: [phone]
Fax: [phone]
[email protected]

3-2

4-1
All preventive maintenance activities must be performed on a regular basis. Performing
routine preventive maintenance actions can aid in providing safe, trouble-free operation of all Cybex
Strength Systems equipment.
NOTE: Cybex is not responsible for performing regular inspection and maintenance actions
for your machines. Instruct all personnel in equipment inspection and maintenance
actions and also in accident reporting/recording. Cybex phone representatives are
available to answer any questions or concerns that you may have.
Chapter 4 - Maintenance
Daily Procedures
NOTE: All inspections and
repairs must be
performed by trained
service personnel only.
CAUTION: Use only Cybex certied replacement
parts when servicing. Failure to do so
could result in personal injury.
1. Upholstery - Wipe down all upholstery using water based disinfection solution.
2. Frames - Wipe down all frames using a mild solution of warm water and car wash soap. Be sure to dry
thoroughly. AVOID acid or chlorine based cleaners and also cleaners containing abrasives as these could
scratch or damage the equipment.
3. Chrome - Clean chrome tubes, rst using chrome polish and then using a car wax seal. Neutral cleaners with
a pH between 5.5 and 8.5 are recommended. Be sure to dry thoroughly. AVOID acid or chlorine based cleaners
and also cleaners containing abrasives as these could scratch or damage the equipment.
4. Guidelines for cleaning front panel:
• Use clean soft cloths or sponges for application of cleaners and again for washing and rinsing.
• Follow up the application with warm water rinse.
• Don’t use abrasives or high alkaline cleaners.
• Don’t leave cleaners on for long periods, wash immediately.
• Don’t apply cleaners in direct sunlight or at elevated temperatures.
• Don’t use scrapers, squeegees or razors.
• Don’t clean with gasoline.

4-2
1. Check all nuts and bolts for looseness. Tighten as required.
2. Inspect all belts (entire length) for any non-uniformity and wear.
Immediately replace belt if any of the following conditions are present:
Weekly Procedures

4-3
3. Some machines use cables in addition to belts. Inspect all cables for wear or damage and proper
tension. When inspecting cables, run your fingers on the cable, paying particular attention to bends
in the cable and attachment points.
Replace all worn cables immediately. The following conditions may indicate a worn
cable:
• A tear or crack in the cable sheath that exposes the cable. See Figure 1.
• A kink in the cable. See Figure 2.
• A curled sheath. See Figure 3.
• “Necking”, a stretched cable sheath. See Figure 4.
Figure 1
Figure 2
Figure 3
Figure 4

4-4
1. Replace all belts and cables at least annually.
Yearly Procedures
4. Inspect bars and handles for wear, paying particular attention to tab area connecting
points.
Replace all worn handles immediately.
5. Inspect snap links for proper latching (indicates wear).
Replace all worn snap links immediately.
6. Inspect for loose or worn grips.
Replace all loose or worn grips immediately.
7. Inspect all labeling for readability. This includes instructional placards, warning and caution decals.
Replace all worn labeling immediately.
8. Inspect all weight stacks for proper alignment and operation.
Correct all improper alignment and operation issues immediately.
9. Wipe Weight Stack Guide Rods clean over entire length. Lubricate with a light coat of medium
weight automotive engine oil.