Cycle Country 25-3130 User manual

1701 38TH AVE W
PO BOX 257
SPENCER, IA 51301
PHONE: [phone]
FAX: [phone]
SERVICE: 800-841-2222
E-MAIL: [e-mail]
www.cyclecountry.com
WINCH
MOUNT KIT
For POLARIS ATVs
OWNER’S MANUAL
MODEL NUMBER: 25-3130
CUSTOMER MUST RECEIVE A COPY OF THIS
OWNER’S MANUAL AT TIME OF SALE
© 2005 Cycle Country Accessories Corp.
Rev. 2
1/16/07 MAN0210

1
6
4
2
5
7
3
Model Number 25-3130
Parts List
Please Note: The Roller Hawse, Cable Clamp, and Cable
Stop are included with the winch.
2
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 CYC3888 Plate, Winch Mount
2 2 CYC3890 Bracket, Winch Mount Weld
3 1 CYC3889 Roller Hawse Mount Plate
4 6 PUR1202 Carriage Bolt 5/16" x 3/4"
5 8 PUR1275 Locknut 5/16" Nylock Clear Zinc
6 4 PUR1142 Bolt 3/8" x 1-1/4"
7 2 PUR1189 Carriage Bolt 5/16" x 1" Clear Zinc
2

THIS WINCH MOUNTING KIT CAN BE USED TO
MOUNT EITHER A CYCLE COUNTRY 1500/2500 WINCH
OR A WARN 2000/2500 WINCH TO YOUR ATV.
All directions referring to right and left are when the rider is sitting on the machine.
Please Note: The roller hawse, cable clamp, cable stop and hardware are included with
the winch.
MODEL NUMBER: 25-3130
WINCH MOUNT INSTALLATION INSTRUCTIONS
1. Align the three holes in the winch mount bracket weldments (Item 2) with the three
holes on the inside of the bumper and secure with the 5/16” x 3/4” carriage bolts and
nylock nuts provided.
2. Place the winch mount plate (Item 1) on top of the winch mount bracket weldments
and secure with the 3/8” x 1-1/4” bolts provided. (See picture above.)
3. Go to instructions for your winch.
4. Assemble the roller hawse mount assembly to the roller hawse mount plate using the
3/8” x 1-1/4” bolts provided. Attach your winch as instructed below.
3

CYCLE COUNTRY 1500 WINCH
INSTALLATION INSTRUCTIONS
•Position the winch in place on top of the winch mount plate, aligning the square holes
of the winch mount plate with the holes on the winch. Be sure that when the winch is
mounted to the ATV, the winch motor is on the LEFT side of the machine.
•Slide the roller hawse mount plate under the winch and align the center set of slotted
holes with the square holes of the winch mount plate and the winch holes and secure
from the underside with two 5/16” x 1” carriage bolts and secure with 5/16” nylock
nuts.
•Go to roller hawse instructions.
4

CYCLE COUNTRY 2500 WINCH
INSTALLATION INSTRUCTIONS
•Position the winch in place on top of the winch mount plate, aligning the four outer
holes of the winch mount plate with the holes on the winch. Be sure that when the
winch is mounted to the ATV, the winch motor is on the RIGHT side of the machine.
•Slide the roller hawse mount plate under the winch and align with the four holes of
the winch mount plate and the winch holes and secure from the underside with four
bolts provided with the winch. The roller hawse mount plate provided with the winch
will not be used.
•Go to roller hawse instructions.
5

WARN 2000/2500 WINCH
INSTALLATION INSTRUCTIONS
•Position the winch in place on top of the winch mount plate, aligning the four outer
holes of the winch mount plate with the holes on the winch. Be sure that when the
winch is mounted to the ATV, the winch motor is on the RIGHT side of the machine.
•Slide the roller hawse mount plate under the winch and align with the four holes of
the winch mount plate and the winch holes and secure from the underside with four
bolts provided with the winch. The roller hawse mount plate provided with the winch
will not be used.
•Go to roller hawse instructions.
6

Roller Hawse Mounting Instructions
Remove one of the long rollers and the two side rollers and feed the winch cable through
the roller hawse. Reinstall the rollers and be sure rollers move freely.
Attach the roller hawse to the roller hawse mount plate using the 3/8” x 1” bolts and
nylock nuts provided with the winch. Tighten all hardware.
See Winch Wiring Instructions supplied with the Winch for proper installation.
7

CAUTION
BE AWARE OF THE CABLE STOP CONTACTING THE ROLLER
HAWSE WHEN THE CABLE IS WOUND IN.
FAILURE TO RELEASE THE SWITCH MAY CAUSE DAMAGE T
O
WINCH PARTS OR TO THE ATV.
When using the Winch to raise and lower a Cycle Country Plow, a
Cable Stop must be installed.
Hook the Winch Cable to the CYC0345 (U608) (item #4 on your 15-0001 push tube
kit) through the slotted hole. Carefully raise the blade until the top of the push tube
are no closer than 1” anywhere on the ATV. Place the Cable Stop onto the Winch
Cable up against the Winch Hawse. Secure the Cable Stop to the Winch Cable using
the Cable Clamp Assembly as shown in the pictures below.
8

ONE YEAR LIMITED WARRANTY
For the period of one year from the purchase date Cycle Country Accessories
Corporation will replace for the original purchaser, free of charge, any part or parts, when
found, upon examination by Cycle Country Accessories Corporation, to be defective in
material, workmanship, or both.
All transportation cost incurred by the purchaser in submitting the material to
Cycle Country Accessories Corporation for replacement under this warranty must be
borne by the purchaser. If Cycle Country Accessories Corporation determines that the
p
roduct must be returned to the factory for credit please call 1-800-841-2222 for an RMA
number and shipping instructions.
The warranty does not apply to parts that have been damaged by accident,
alteration, abuse, improper lubrication, normal wear, or other causes beyond Cycle
Country Accessories Corporation’s control. Products such as engines, electric motors,
and actuators may carry an original manufacturer’s warranty. Please call Cycle Country
Accessories Corporation for information.
1701 38TH AVE W
PO BOX 257
SPENCER, IA 51301
PHONE: [phone]
FAX: [phone]
SERVICE: 800-841-2222
E-MAIL: [e-mail]
www.cyclecountry.com
9

10
Cycle Country Accessories Corporation has been a world-renowned manufacturer of quality
ATV products since 1981 and we hope you will enjoy your new Cycle Country accessory.
We’re the Industry Snow Blade leader:
48”, 54”, 60” & 72” Bear Force Straight Blades 52” & 60” State Plows
72” ‘V’ Force Plow System “New” A.R.M. 52” Plow available in Poly or Steel Blade
If a winch is what you must have, then you’ve come to the right place:
1500lb and 2500lb Winches
We also have an extensive line of winch mounts for both Cycle Country and Warn winches
If you need to haul more gear on your quad, check out our baskets:
Front Basket Rear Basket Rear Drop Basket
All Purpose Basket “New” Poly Rear Drop Basket
If you need to mow the trail before you go riding one of these will help:
Our 54” finish cut Quick Silver 54 can be mounted in front or towed behind your ATV
The 48” Rough Cut will handle your toughest mowing jobs
The Rough Cut 44 provides an economical way to handle all your mowing needs
If you are into deer hunting and want to make a food plot, you will love our 3 Point
Hitch & Implements:
Rear Blade Moldboard Plow Furrower Rake
Cultivator Disk Harrow
If you have a landscaping or gardening project, check out our “Work Ready” Tow
Behind Implements:
Universal Tow Frame Cultivator Rake Rear Blade
Disc Disk Harrow
And many more accessories to help you Work Hard and Play Hard:
For more information call us at 1-800-841-2222, or on the web at www.cyclecountry.com